The part about installing the drain after the pan is installed when one has a concrete floor was very helpful. Thanks!
@DjShakaShawn
6 күн бұрын
Awesome video. I'm ready to do my renovation now. Thank you!
@ericfournier1500
2 жыл бұрын
Great job! You went in details on the part that nobody showed in my research so far.
@marval550
Жыл бұрын
I appreciate your video sir! I liked the close ups and trial & errors because I’m sure I’ll run into similar issues. You were very thorough :)
@kenhobbs9251
Жыл бұрын
Put it in wet mortar and it won’t squeak or have hollow spots
@mayma9642
2 жыл бұрын
Great job!!! Thanks for sharing your expertise and knowledge. This will help me out when I do my installation 👏👏👏
@clipperlawncare4770
Жыл бұрын
Awesome Job!!!!.... I have to install a shower pan for the first time and your video will certainly help with the install......Thanks so much for taking time to share your knowledge and experience with people like myself that have zero plumbing experience. Also, thanks all those that shared their comments and pointed out how the install could be improved. I am now a subscriber.
@trtlgrdl
2 жыл бұрын
This was great man, its the exact replacement i need to do. Thanks for taking the time. Subscribing.
@dommed2978
10 ай бұрын
Very good video Sr. but missing the part to remove the old tub! Anyways thanks so much for your effort!
@dreadfullradu4726
6 ай бұрын
Great video, very detailed and very informative. I understand now some things that i couldnt figure out. Thank you so much!!!
@wilfredoroque4977
3 ай бұрын
Your video was awesome, thank you. very much sir. I learned a lot from this video and yes, I'm doing a project just like the one you're doing now, hopefully. it'll workout for me. Thank you again, and God bless you.
@waynepatrick8124
2 жыл бұрын
Great video. Thanks for recording it!
@darrell7976
Жыл бұрын
Yes thank you very much you’re the only video showing in detail how to
@jonklause5130
2 жыл бұрын
Great video. I appreciate how you show detail And how sometimes we have to make adjustments. Thanks you.
@lakeman59
7 ай бұрын
You installed the rubber gasket upside down beveled side down
@johnpavich5222
8 ай бұрын
😊one bit of advice to prevent a lot of hair going down the drain go get a small stainless steel screen and put it under the final big square hole drain cover. It will save you a lot if grief. Also between those shims a good idea would be to put some pure silicon so that the shims are not taking up all the weight and it will be distributed evenly. Otherwise good job! I installed a small semi circle shower years ago and after about 7 or 8 yrs the threads became.e loose enough that the drain started to leak. I guess the constant use of the showers caused the threads to loosen. I think it would be a good idea to silicon the threads on the under side of the shower drain so they won't get loose over time . What do you think?😊
@briantfunkfunk3770
5 ай бұрын
word of advice for the DIYers out there. You should put a layer of cement under the pan about a half inch thick or so to really anchor this pan.
@bobvbk2802
6 ай бұрын
Perfec t as i have a concrete floor to .. Thanx for the great video.
@voice-of-reason5780
2 жыл бұрын
Great job! You're very handy.
@manuelgil6728
5 ай бұрын
Nice, i like the idea of the silicone around theead seal will last longer and not be exposed to water . Awesome.
@ateshnarayan9769
Жыл бұрын
Well presented I am learning from your work of teaching. God bless you forever
@moiseslopez4982
Жыл бұрын
great video showing all details needed to install shower pan
@bigabencoado3668
2 жыл бұрын
Great job!! Bom Trabalho ,aprendi muito . Thank you .
@tpformybunghole1974
2 жыл бұрын
Thanks for making video, I'm about to do my bathroom and I'm collecting info from various videos.
@wyattsdad8561
6 ай бұрын
Thank you for making this!
@Lockdown454
2 ай бұрын
Can you use dish soap to get that rubber bushing in easier, seems stabbing at it with a flathead could tear it.
@ryanbuck3789
5 ай бұрын
I’m sure there’s probably tons of comments but I’m not gonna read through them. The first couple didn’t mention it but did anybody else see your problem right away PVC glue on ABS pipe. Nah bro. Had me fool that first day. This was a video somebody knew what’s up.
@Jfff-ugfgh
2 жыл бұрын
Great job man.
@tramellcanady4914
Жыл бұрын
Why didn't you put mortar under the pan to hold it in place?
@leaguefixesyourmatches8259
9 ай бұрын
very nice installation. The tilers lied to me that you couldn't just replace the shower pan.
@robertpongallo4079
Жыл бұрын
Excellent video thank you for sharing
@genevie209
11 ай бұрын
Thank you sir for that nice video I learn a lot from it and please never mind the negative comments your doing just fine I’m fallowing you for sure
@BARUCH6223
2 жыл бұрын
Very nice sir Great job.
@mrsalsiviris
2 жыл бұрын
Very nice install!!
@user-tb9ih4fd2x
2 ай бұрын
HELP. question- black pipe came out of the shower pan. How could this happen? several plumbers say they would have to dig to fix etc but none clear on why or how this happened so can you explain how n why this happened? I had no leaks, nothing looks broken or cracked, the edges of the pipe were smooth after I cleaned off I saw the black rubber ring just like the one you set in so wth happened
@larainehaworth8215
2 жыл бұрын
What are the fasteners called you used to fasten to the studs
@DannyShaw3388
2 жыл бұрын
A job well done!
@SciaticaDrums
2 жыл бұрын
Is that a mobile home shower pan? 27x 54? No reinforcement under the pan? The underside looked pretty supportive.
@hugoascencio9665
2 жыл бұрын
What are those "little things that fit over the edge" called? cant seem to find them. thanks in advance.
@ecgwyo
2 жыл бұрын
You should have used ABS glue, not PVC glue, they are different for the different type of pipe.
@alvinrodriguez580
Жыл бұрын
Why would you not use PVC glue? That pipe he is replacing it with is not steel. It's PVC.
@ajsemtb
Жыл бұрын
@@alvinrodriguez580 It's not PVC, its ABS plastic. It's different and requires different glue.
@robinhall411
Жыл бұрын
They sell a transition cement to glue black to white pipe also.
@richardlopez9619
Жыл бұрын
Yes you are right about ABS glue for abs piping..
@williamreese2477
Жыл бұрын
He is using cement! Not the glue.go work stop hating
@rajvirgill5331
2 жыл бұрын
Very nice 👍🏻
@Denis-bo8ms
2 жыл бұрын
great video!
@G-Man10066
Жыл бұрын
Great work Sir you are very detail oriented! Thanks for sharing.
@limamantapachitas
Жыл бұрын
great video , but my question why not use of plumber's putty instead of silicone
@mikepellegrino514
2 ай бұрын
That silicon on the castle nut is not only unnecessary but looks bad through the grates. At least use clear. But worse than that is, you didn't use a mortar bed. That pan will move and flex and eventually crack.
@85Z28
8 ай бұрын
👍 good job..
@bkhoavo
Жыл бұрын
good job with leveling the floor
@shaundonovan2193
2 жыл бұрын
Nice install for sure
@willhopson8797
2 жыл бұрын
where do you buy the shower pan and what size is
@trutheye1
2 жыл бұрын
You should wrap any piping where it comes into contact with concrete. If you don’t, you risk breaking the pipe due to expansion and contraction.
@ryanbuck3789
5 ай бұрын
It’s to keep the lime from eating it over time. The1-2in of foam wrap around the outside is so after concretes poured you can then pull that foam wrap and you have a bit of wiggle room to like the p if it’s not perfect like coming up thru walls if it’s out a bit you can push it back in the wall
@kirstenvivian2104
5 ай бұрын
What are you going to do with the shims that you wedged underneath the shower pan?
@1902justchevy
Жыл бұрын
The shower pan I have says to put 1 to 2 inches of morter cement under it . The dude uses channel locks backwards.
@hrdrymr23iii64
2 жыл бұрын
is that pvc glue for abs pipe?
@briandazzo-du6sl
9 ай бұрын
How did u connect to the old drain ?
@ricwilmot1654
5 ай бұрын
Good video helped me do mine
@franciscojavierestrada7585
5 ай бұрын
I just ran into that problem between a 1 1/2 " pipe to a now "2 inch
@NinjaPatvstheworld
2 жыл бұрын
Merci!
@jerryskot1004
Жыл бұрын
PVC solvent on ABS pipe? You should have used YELLOW ABS solvent. Fingers crossed it holds.
@auctionmusic
Жыл бұрын
is your foundation under tension?
@MAGAMAN
Ай бұрын
NEVER hit two hammers together. Hardened metal is brittle and razor sharp shards can fly of injuring or even blinding you. Use a proper concrete chisel.
@Mario-xh6wy
2 жыл бұрын
Does the shower drain comes with everything, with the rubber or you buy stuff separately?
@lourainwater676
Жыл бұрын
Yes, both gaskets, the drain cover and the key to tighten it
@darleneb.1514
7 ай бұрын
Great video. Can you replace my tub with a shower?
@joefabre7699
5 ай бұрын
I would be concerned that you didnt use abs bonding agent. (Cement) always make sure your materials match
@BelloCruz
9 ай бұрын
👍
@richardlopez9619
Жыл бұрын
And your floor you should have put cement underneath your shower pan it will stop the cracking in your shower pan another tip and you need ABS glue for abs piping baby shower is going to crack if you don't put loose cement....
@abusabi11
2 жыл бұрын
You need to also either use foam or silicone as a bed for your pan. For future reference…
@farehamboy90
9 ай бұрын
Never use shims as this will cause the tray to crack overtime. Bed down the tray using mortar and this will ensure the whole tray is supported properly.
@janitojr1
2 жыл бұрын
Where's the links to parts 2, 3, &4?
@jerryskot1004
Жыл бұрын
11:51 thats not quite level. Not bashing, just observing. Likely out a quarter inch or less
@richardgrass1382
2 жыл бұрын
Oh my
@mariosifuentes5994
Жыл бұрын
If that drain ever get plugged wont be fun to try to put an auger down …
@angusblack9900
8 ай бұрын
Why put concrete in it
@kintectribe2219
2 жыл бұрын
You should do that better. It's interesting how your cousin's give you positive comments. Anyway thanks for the video.
@angusblack9900
8 ай бұрын
You didn't show how you moved the pipe to hit the hole
@deniseabu-arab1393
3 ай бұрын
Yes he did at the very beginning
@taylorschulz6522
2 жыл бұрын
That's ABS though, not pvc..
@Lugenfabrik
2 жыл бұрын
I think plumbers putty might have been a better option than the silicon?
@cdurch1
2 жыл бұрын
Maybe, maybe not... I've seen elsewhere that silicon is more appropriate to use on the more flex-prone shower pans. The reasoning was that the plumbers putty dries and eventually losses its flexibility over time. With a flexing floor, gaps can occur and these leads to leaks. The silicon is less prone to lose its flexibility over time. However, for nonflexing pans, putty is the preferred option.
@deputydan2226
2 жыл бұрын
Can't use plumber putty on acrylic.. I mean you could but it deteriorates it
@taylorschulz6522
2 жыл бұрын
Plumbers putty will dry out over time. You always want to use silicone on shower pans
@dooleyfan
Жыл бұрын
@@taylorschulz6522 you are exactly right. Sadly, I know this from experience!
@farehamboy90
9 ай бұрын
You are using your channel lock grips the wrong way
@evelynrojas2952
Жыл бұрын
he's using the wrong screw that screw is for dry wall and not for secure shower pan
@sklee1644
Жыл бұрын
Something is missing.
@leon7764
Жыл бұрын
32.30
@dunklechuck1188
2 жыл бұрын
Make your own pan…. Problem solved
@johnsmind
2 ай бұрын
BRO?? YOU JUST BYPASSED THE MOST IMPORTANT PART. Show how you put the pan on with the drain attached and then seal it. You just skipped to it being in. AND IF you DON'T put mortar under the pan it will crackle when you step on it if you're big. WTF. WASTE.
@ClaytonYatescarenthusiast
2 жыл бұрын
Wrong glue
@guillermoescobar1512
2 жыл бұрын
Old Profesional
@henryandino4653
3 ай бұрын
Falto la goma
@MAGAMAN
Ай бұрын
This guy fails through the entire video and people tell him he did a good job. lol Seriously, he fails at leveling the floor. Tells you it's level while you can hear it rocking back and forth. Uses shims which most manufacturers say not to use because it still isn't level. Doesn't use anything under the shower pan so it will constantly make noise when shower is used. Uses way too much caulking on the drain. Installs the shower brackets with drywall screws which will rust immediately. Smears caulking all over the inside of the drain which is completely unneeded and will be visible through the shower drain grate. 6 months and this whole thing is going to need to be torn out and replaced again. I'm really curious how he thinks he's going to waterproof that joint in the tiles when they are replaced.
@bkhoavo
Жыл бұрын
wrong glue. and i'm an amature diy-er
@evelynrojas2952
Жыл бұрын
what kind of job is that ? terrible finish
@vernonpipkin7975
Жыл бұрын
Gasket upside down
@kchilz32
Жыл бұрын
Beveled edge up.
@kchilz32
Жыл бұрын
kzitem.info/news/bejne/ppuOrn2GcJF_Z4o
@user-uf2cv3el9o
Жыл бұрын
channel locks backward
@thomasryan5681
Жыл бұрын
Backwards channel locks was definitely an inexperienced installer move. Plus no mortar under the pan. Fiberglass pans will get spongy.
Пікірлер: 111