Thank you very much Sir for your efforts firstly and for sharing and teaching us with this useful information about PLC
@plcgoods
2 жыл бұрын
It's my pleasure glad to have you in the channel!
@framos9991
Жыл бұрын
Useful information/ Thanks!
@plcgoods
Жыл бұрын
Glad it was helpful!
@weerapongsuanto8921
3 жыл бұрын
I like yours
@plcgoods
3 жыл бұрын
And I like your visiting the specialized on PLC channel and having you as my subscriber!
@Lucky.Red0708
3 жыл бұрын
Amazing GOOD JOB
@plcgoods
3 жыл бұрын
Hey glad you liked it!
@lyaeusv3828
3 жыл бұрын
Subscribed !
@plcgoods
3 жыл бұрын
Thanks for joining our channel, and find its content interesting!
@gilbertdevera3339
2 жыл бұрын
do you have tutorial about Servo or Robot programming sir by the way thank you for this tutorial
@plcgoods
2 жыл бұрын
Thanks for checking the channel out, right now i do not have any tutorial regarding the Servo or Robot programming subjects!
@nsralsham9511
3 жыл бұрын
where is the video which you have designed the HMI for controlling the PID project? , thanks
@plcgoods
3 жыл бұрын
In the description it says "Basics of on/off controllers - Effects of deadBand and set point settings of on/off controllers -PID controllers"
@piyushjangid5219
2 жыл бұрын
sir i have a level transmitter and i want to use this as a sensor in my esr and the ai is a current type(4-20am) so how i can do this please help i mean in range set etc.
@plcgoodsteam8934
2 жыл бұрын
Hi there, In this video I've explained the program that can modify the input analog range (Time 6:50 to 7:00). Also this video ( kzitem.info/news/bejne/zWOPm2ptq2Nnhno ) can help you in details, to learn how analog inputs can be read or sent.
@plcgoods
2 жыл бұрын
Thanks for checking out the channel!
@mohdnauman5012
2 жыл бұрын
I am putting the same PID parameters as yours....but my fill is just giving 0 or 10 output not any value between them
@plcgoods
2 жыл бұрын
Well! what can I say beside the fact that you and me know the software does not discriminate against the programmers, please watch the videos more carefully before asking me what the problem of your work might be
@mohdnauman5012
2 жыл бұрын
@@plcgoods 😂😂I was making a blunder...sorry
@nyanphyoaung5661
3 жыл бұрын
why you test with 1500 and change to 1200, and can't fine IW34 in factory io
@plcgoodsmentor9223
3 жыл бұрын
Hello, First, I tried to simulate PID using 1200 CPU, but it seems there is a bug inside TIA Portal software. Because TIA won't simulate the PID correctly, when a virtual 1200 CPU is used as the controller (see the video. Time 10:26). So, I used a 1500 CPU to solve this problem. Pay attention, the PID instruction will work correctly, if you use real 1200 or 1500 CPUs.
@plcgoodsmentor9223
3 жыл бұрын
Note that, You can modify PLC addresses inside Factory I O. Go to File-> Drivers-> Configuration, and then modify I/O Config and Also I/O Points
@plcgoods
3 жыл бұрын
all right?
@nyanphyoaung5661
3 жыл бұрын
twist the example
@plcgoods
3 жыл бұрын
?:)
@AhmedMohamed-SCADA
3 жыл бұрын
how can i convert this system to T.F to help me to make tuning on matlab ?
@plcgoodsmentor9223
3 жыл бұрын
What's T.F?
@plcgoods
3 жыл бұрын
Could You Please Clarify…?
@nabilmarsel8792
3 жыл бұрын
@@plcgoods he meant Transfer function.
@mrhamidou9871
2 жыл бұрын
Hi Can you give us the total program in 'Main' ? and thank you for the videos.
@plcgoods
2 жыл бұрын
Hi there, The program inside the Main block is very short. You can use the video, the time between 6:50 and 7:00, to write the program. Note that the "Norm" and "Scale" instruction were explained in the previous videos. If you have another problem, please write it here.
Пікірлер: 32