This fix improved my feed reliability a lot (talking about smoothing the edges). Thanks very much for the video. I have one further suggestion: I used emery boards instead of sandpaper. They are cheap and semi-rigid, making it easy to sand evenly.
@averyostrowsky8692
5 ай бұрын
Had issues myself with the first 3 range trips. Frustrated, I’ve Since educated myself on loading the magazine correctly and now it functions great. A uniform stack as you described, each round stacking left, right, left etc, is KEY! Tip, If you notice one round out of place, tip the mag upside down, pull back the tab to release pressure, give it a tiny shake and it sets the round back in its place and continue loading. If you stack it right, it’ll shoot right. Simple.
@redarmory
5 ай бұрын
You are correct about making sure the rounds are loaded into the magazine correctly. If not, it definitely will create malfunctions. Also noticed that these magazines swell when loaded fully. Thanks.
@PetervanderGoes
3 ай бұрын
First, thanks very much for offering a procedure to help alleviate thee mag issues. I tried your fix on 4 mags, and the feed reliability is much better. Between training myself to *carefully* load the mags to ensure proper alignment and applying your fix, I am actually starting to enjoy my P322. I have one further suggestion. Instead of sandpaper, I used emery boards which are semi rigid and make it easy to evenly smooth the edges.
@redarmory
3 ай бұрын
Thanks for adding a comment that might help others with similar mag issues.
@BlackwellVlogs
2 ай бұрын
I do agree that mags need to be sanded inside. Was thinking about it after seeing certain brands get stuck in the middle of the mag. Thank you for the confirmation!
@stevemccormick3968
2 ай бұрын
I have had a Sig P322 for about 10 weeks. It is used almost daily in training classes. Have fired more than 5000 rounds through it with zero problems. Anytime I buy new mags, for any gun, I clean them thoroughly before use. As for these mags they have run flawlessly since day one. I disagree with this video in that it is important to keep pressure on the round you are loading in order to avoid rim lock. The included load assist device does just that. I do agree that the stacking should be checked for alternating seating in the mag. If you cut off a coil you may experience malfunctions after extended use so be aware of that when choosing to do so. Otherwise this is a nicely done video instruction.
@redarmory
2 ай бұрын
Thanks for your input, I do agree with you about making sure to do what you said before doing any mods. This is a last resort, so do it at your own risk.
@Valorius
8 ай бұрын
These mags are definitely subpar. They should've been made out of steel.
@redarmory
8 ай бұрын
I agree, got one mag that when fully loaded it was hard to insert into the pistol. Hopefully the new P322 Comp will be better.
@Valorius
8 ай бұрын
@@redarmory 2 of mine, if I load more than 13 rounds, will not drop free from the handgun, which is obviously a mag swelling issue. My 25 will only work with 10rds. I think if they made these mags from steel, all issues would disappear. One thing is for sure; it is an *incredibly* accurate handgun. I uploaded a video shooting mine at 153yds offhand against a leaf.
@redarmory
8 ай бұрын
@@Valorius I will check out your video.
@PetervanderGoes
3 ай бұрын
@@Valorius Steel would be good, but not really necessary. If KelTek can make poly mags for their P17 pistol that hold 16 rounds and perform *reliably* (I own one, never had a feed issue). Sig should be able to provide decent mags for a gun that costs twice as much!
@jasonjaeger4042
Ай бұрын
Bought a P322 Comp and was very excited to shoot it. Went straight to my range and was pretty let down. The RomeoZero Elite RDO it came with is garbage, when you try to adjust it you turn say clockwise and the dot will raise. Then if you try to bring it back down a tiny bit the slightest twist moves the dot probably 15moa....FROM A SIXTEENTH OF A TURN LITERALLY. Same goes for your windage (left or right). So I got rid of that garbage rdo. Then the mag feed issue, the lack of parts available, the absence of a parts explosion, just not worth the $600 I paid for it. For that much $ for a 22 there should be NO problems at all. Meanwhile my Canik MC9 has had 9500rds thru it and not ONE malfunction and it's supposed to have a bunch of issues......not buying a sig ever again. Trigger is garbage too.
@redarmory
Ай бұрын
@jasonjaeger4042 I agree the red dot is not ideal, I'd prefer a lower price point and letting me pick the dot...or include the updated RomeoZero. I did not have any issues with zeroing the dot, but you are correct that the adjustment screws don't have feedback. For me, besides the occasional light strike and feeding issues before the mods, the pistol is actually fun to shoot now. Hope you get all the issues figured out.
@jasonjaeger4042
Ай бұрын
@redarmory got the mag issue sorted but shouldn't have to when ya pay that much for a .22. When it's running smooth it's great, but still disappointed with my purchase because of all the problems I had. Should have just bought a Ruger 10/22 rifle
@jasonjaeger4042
Ай бұрын
I just ordered some springs that are 1.0mm thick compared to the factory spring which is .6 or .7mm thick. To me it seems like there is not enough spring pressure, but I see you're thinking it is too much spring pressure. Just curious as to why you think that and if cutting the spring shorter helped? Will let you know in a few days if the 12mm x 1mm spring works better. Appreciate ya taking the time to make the vid. Pretty frustrating purchasing a gun and problems right from the start.
@redarmory
Ай бұрын
@jasonjaeger4042 One of the reasons I cut the springs was that when fully loaded, the mag body swelled, and mag would not drop free. After cutting the springs and making sure not to let the spring push up on the cartridge as I load each round, the mag dropped free from the pistol. I do not dismiss that following the factory instructions to make sure each cartridge is staggered helps, but that doesn't always correct malfunctions. I would like to hear back once you replace the springs. Thanks.
@jasonjaeger4042
Ай бұрын
@redarmory the springs should be here tomorrow (it says Sunday....but never got a delivery on a Sunday before). But will definitely let ya know!
@slicksmokegaming9857
24 күн бұрын
@@jasonjaeger4042how did it go?
@jasonjaeger4042
23 күн бұрын
@slicksmokegaming9857 the 1mm thick springs didn't do shit.....pretty pissed. Figured they'd be stronger but must be a shit metal and are pretty much the exact same tension as the factory ones. Back to the drawing board! 🤬
@slicksmokegaming9857
23 күн бұрын
@jasonjaeger4042 hmm I had heard on a forum that was a fix and gonna try myself. Would Def thing a stronger better spring would feed better but never know with rimfire I guess..
@petemitchell6788
9 ай бұрын
Only issue I had was not loading them correctly to begin with. Use the included loader and load it like any other mag. Do not pull the follower down enough to break contact with the round. The complete OPPOSITE of what this 🤡 is saying. Do NOT void your warranty and ruin your mags like this 🤡
@redarmory
9 ай бұрын
🤣🤣🤣 Thanks for your input.
@mlast3264
4 ай бұрын
Thank you
@Valorius
8 ай бұрын
Also, have a subscription from a fellow small gun tuber. We little channels gotta stick together. ;)
@redarmory
8 ай бұрын
Thanks, will do the same.
@Valorius
8 ай бұрын
@@redarmory Awesome. :) I have a Sig 322 playlist you might enjoy. have a great night!
@donwatkins9769
10 ай бұрын
I can't believe a quality company like Sig released such a poor quality firearm. If there was anyway I could return mine I would. I have other Sig firearms and love them but the P322 is a piece of junk in my world. I was at the range yesterday and never fired the Sig 22 once. It was embarrassing to have other shooters watching me as I unjammed two clips and never fired. I can't believe I am going to have to perform some gunsmithing on a new Sig to make it work!!!!
@redarmory
10 ай бұрын
I agree with you concerning the issues that many are having with the P322. So far with the modification to the mags and not letting the follower push back up while I am loading it, it's been fun to shoot. If you haven't already, reach out to Sig. Many have had good CS response from them.
@donwatkins9769
10 ай бұрын
Thanks so much for the QUICK reply. I guess I will call Sig of Monday and see what is involved with them hopefully correcting the issue. @@redarmory
@petemitchell6788
9 ай бұрын
They work fine as they come. This is a hacktuber
@redarmory
9 ай бұрын
@@petemitchell6788 🤣🤣🤣 Thanks for your input.
@donwatkins9769
9 ай бұрын
Sent to Sig and got back in less than a week. Excellent service. They said they did a few things and fired 50 rounds, and no issue. Can't wait to try.
@blenke1
2 ай бұрын
10 "Uhhs" in 20 seconds.
@Ricksterpt
8 ай бұрын
Terrible Gun...
@redarmory
8 ай бұрын
Sorry to hear that, It seems like a hit and miss when it comes to reliability. At first it was feeding issues and then light strikes but now it's been running fine. Hopefully with their new model P322 Comp soon to be release, they worked out all the bugs.
Пікірлер: 53