This was very useful, thanks for sharing and the detailed talk through. I'm a beginner with this stuff and look forward to more of your excellent videos.
@anissoulhaci2653
3 жыл бұрын
Thanks ! Mate
@ConsertandoTudo
Жыл бұрын
i don't know if you are still with this oscilloscope, or about your conditions, but I just bought this oscilloscope: Dso2512g in Ali Express, and it just works fine. Not so expensive, 80usd.Great video!
@philipgiacalone5605
Жыл бұрын
Thanks for sharing your project. How did you get a sine wave output? I am only able to get the si5351 to output square waves.
@ElbaSatGuy
3 жыл бұрын
Good, informative video. Thanks for sharing it and the code sample. The device specification claims a square wave output across its range. The sine appearance might be due to scope bandwidth; do you see CLK0/1 both square wave at audio frequencies?
@anissoulhaci2653
2 жыл бұрын
Sorry for late well . Its not about the oscilloscope bandwidth .its about synthesizing signals on higher frequency
@FantaBH
7 ай бұрын
I am surprised you got only 780 subs, did not check full channel contain to see if u upload regularly but according to this video I watched you deserve much more .
@anissoulhaci2653
7 ай бұрын
Thank you so much brother i really appreciate , i will be back ASAP!
@marco_di
11 ай бұрын
Do you also have a solution for how to protect sensitive electronics from high-frequency ignitions of TIG welding machines?
@F_Tim1961
3 жыл бұрын
Essentially if this code can be fitted into the Nano that sits in the AT-20 or other generic radios you have a signal if Sinufied that can run the Rick Campbell SSB Phasing exciter from ARRL archives that I have detailed elsewhere on this board. I am suspicious about the OP CLK0 being a Sine wave but this is easily fixed via either of the two ccts I have detailed The GND gate FET schematic is of course more frequency sensitive to movement away from the design point . 73,s TEFidler Nouvelle Zelande.
@Linas_LY2H
2 жыл бұрын
Thanks for an interesting and useful info! I've just been looking for the Arduino sketch information for my Si module which I found in my junk-box. I am planning to use it to improve my old crystal controlled transceiver. Subscribed! 73! Linas LY2H
@anissoulhaci2653
2 жыл бұрын
Enjoy man ! 73s
@godsowncalicut1438
2 жыл бұрын
Sir pls reply
@mohammedmosta8801
3 жыл бұрын
Thanks for the information, we are waiting for new video 98
@bmsfx
Жыл бұрын
whats the maximum frequency output power? i need something that can do 8khz and 33khz at around 10W output power (or more) for making my own cable and fault locator
@avcimustafa7052
Жыл бұрын
thanks.
@effectivecode6140
2 жыл бұрын
how can we make sdr of freq 1ghz? do you know anything about it?
@F_Tim1961
3 жыл бұрын
Hold that thought Aniss.. I will send you a schematic to take a low level TTL signal and get three watts RF out of it on twenty metres. Essentially with minor tweeks what you show plus the existing chassis can be a three or four band CW QRP or even 10W transmitter for the work involved in making up a simple PCB and also adding a keyer cct and software to the Nano in the AT-20 or whatever brand of radio is used. TE Fidler
@claudioi2ndt313
3 жыл бұрын
just a question: why clock 0 looks like a "sinus" while clock 1 seems to be a square wave?
@F_Tim1961
3 жыл бұрын
It's a mystery to me as well.. all those CLK0, 1 etc outputs are supposed to be the same. I can't see why it should be anything but a Square wave. TE Fidler
@anissoulhaci2653
3 жыл бұрын
When it outputing higher frequency it goes more into sinusoidal because its digitizing ( higher resolution rate) more than lower frequencies
@radiorider8249
3 жыл бұрын
Congrats ! Very nice and useful video. Thanks. 73 Denis F6CRP
@anissoulhaci2653
3 жыл бұрын
Thanks !
@abderrahmanebkt6042
3 жыл бұрын
Nice video mate 98
@anissoulhaci2653
3 жыл бұрын
Thank you mazouna
@godsowncalicut1438
2 жыл бұрын
Can we sweep frequency from 10mhz to 50 mhz and return
@anissoulhaci2653
2 жыл бұрын
Yes there is a sketch inside the si5351 library
@earthisgoodforeveryone
2 жыл бұрын
How You connected the output to sdr ? pls reply very important now 🙄🙄
@anissoulhaci2653
2 жыл бұрын
The both i and q signals are connected to stereo line in I ---->L Q ---->R (OR SWAP IT) GND ----> GND
@earthisgoodforeveryone
2 жыл бұрын
Plz connect a display and a clickable potentiometer with it 🥺 plz make a dds vfo full
Пікірлер: 30