Hoy justamente me dio esta falla en mi moto, gracias por tu aporte... Ya tengo una idea de como debera reparar la moto el mecánico... Saludos
@SkateSpace2012
2 жыл бұрын
High temp sealant did not work for me, luckily I could order the original gasket from the Benelli dealer . Lucky for you the sensor was still oke.
@extrudervadim
2 жыл бұрын
This repairing was done in May 2021. I've already run more than 5000 km and everything is OK with crankshaft sensor and engine in general. But you right, the original gasket better.
@user-mc5xz5vr6e
2 жыл бұрын
Била такая же проблема лечил точно также
@extrudervadim
2 жыл бұрын
Коренная причина - дубеющий пластик наружного кембрика. По хорошему, лучше нижнюю часть или весь заменить на силиконовый. Он остаётся эластичным при 200 градусах и не стареет так сильно
@MRsickcat84
3 ай бұрын
I noticed after repair, the bike still gives P0031 error and won't start. What you need to do is reset the ECU after repair, because the code still stored for every electronic error. How to do it is the same as other Delphi motorcycle.
@extrudervadim
3 ай бұрын
Usually ECU reset by disconnect negative pole of battery for few hours
@MRsickcat84
Жыл бұрын
Hi, i just got P0031 error. Do you know the difference between front and rear cylinder Oxygen sensor? There is two types of oxygen sensors mentioned in error code tables and its confusing which part it refered to
@extrudervadim
Жыл бұрын
Our scooters use, of course, one Oxygen sensor. As i remember, front one. I've already changed it in my scooter. When it's cold - engine works perfectly. But in 30thy minutes sensor heating up and loose a signal. As I know, it's frequently error.
@MRsickcat84
Жыл бұрын
@@extrudervadim the error shows when cold hence it can not start. Okay it looks like the only O2 sensor is the one on the exhaust. I will try to examine it
@MRsickcat84
2 жыл бұрын
Hi. We have so many instances of burnt coil in here. Any ideas why?
@extrudervadim
2 жыл бұрын
Actually, never heard about this issue in Ukraine. Maybe Benelli made some costs imprudent and use chipper supplier for coil?
@MRsickcat84
2 жыл бұрын
@@extrudervadim we are also suspect this. Also being in tropical climate probably one disadvantage to owners
@MRsickcat84
2 жыл бұрын
@@extrudervadim we suspect it either
@user-sy3xk7wd7w
Жыл бұрын
My silverblade 250 bike shuts off because the rpms are between 2000 and 1000 this started when a new stator was installed
@extrudervadim
Жыл бұрын
Not clear an issue. Does engine start to work up to 2000 rpm and then shuts off or even can not start because of rpm are low?
@user-sy3xk7wd7w
Жыл бұрын
La moto enciende normal pero en los semaforos las rpm caen tengo que estar acelerando para que no se pare
@extrudervadim
Жыл бұрын
Are you sure, that rootcause is new stator? Looks like some issue with fuel system
hello need your help please have error code P0118 thought it was the temperature sensor unfortunately the error is still there what could it not be the thermostat?
@extrudervadim
2 жыл бұрын
Error P0118 means broken of wire to temperature sensor. Did you measure the real temperature of cooling liquid? Should be not more, then 90 C
@martescuovidiu87
2 жыл бұрын
@@extrudervadim thanks for quick reply If I let it run while it is stationary, it comes to about 83 degrees according to my measuring device. Then the display shows 2 dashes in the temperature display. After about 1 minute, the fan switches on and goes back to one dash FI always lights up red I have already replaced the temperature sensor which is screwed into the engine without success
@martescuovidiu87
2 жыл бұрын
@@extrudervadim wie kann ich messen die 3 Pins A,B,C wie viel Volt müssen die haben bei Zündung an ?oder bei laufender Motor
@martescuovidiu87
2 жыл бұрын
soory said the fan comes on at 73 degrees and off at about 65
@extrudervadim
2 жыл бұрын
@@martescuovidiu87 I think, I've got you issue. Your scooter works absolutely normal. Temperature is OK, indicator on dashboard also works as usual on our scooters. Problem on red flashing FI indicator - it's a residual phenomenon. There is two solutions. One: disconnect your battery for few hours, better days. Second solution: just ignore this error, in one month it's dissappear automatically
@asrulmargaluyu4368
Жыл бұрын
Rpm motor SilverBlade saya tidak stabil.. cara memperbaiki nya bagaimana Salam kenal dari Indonesia
@asrulmargaluyu4368
Жыл бұрын
Apakah anda punya kontak WhatsApp?
@extrudervadim
Жыл бұрын
First you should found the root cause, then thinking how to solve the problem 😉. Do you have any error from ECU?
@extrudervadim
Жыл бұрын
Let's keep discussion in KZitem
@asrulmargaluyu4368
Жыл бұрын
Lampu FI tidak menunjukkan permasalahan, Mesin menyala namun RPM tidak stabil
@extrudervadim
Жыл бұрын
Difficult to say exactly. You should check fuel pump (filter of it), injector, air leak, sensors on intake duct...
Пікірлер: 38