Good but keep in mind new welders some places don’t allow whipping due to “ not consistent enough penetration “😢😢
@migstickwelder1992
11 ай бұрын
true, its all about where do u work or learn, and what quality of weld they need ‘A ‘B or ‘C
@fredramos9206
11 ай бұрын
This technique works well for me on plate 1/4" and thinner on the penetrating respect!,....Regards from S, TX.
@jdmac150
11 ай бұрын
True. I’d get in trouble where I work if they caught me whipping.
@douwetendam5097
11 ай бұрын
I been thinkin about that, lets say you lay your root as a straight bead, no movement once however, and the rest on top using the whip n pause, wouldnt you get all the penetration you need? Since its high amp spray welding i dont see fusion being a problem 🤔
@crzy2c
8 ай бұрын
Thank you was thinking the same thing
@stewartgani9390
Жыл бұрын
Ahh..., the good ol' push and pull tecnique, nice 👍👍
@philipmullett6216
4 ай бұрын
Unnecessary.
@bournelucid
2 ай бұрын
Whip
@Revok7272
Ай бұрын
Penetration can be better like this if you know what you doing
@giftdcam8472
25 күн бұрын
@@philipmullett6216idk most want stack dimes not caulk lines so hence the whip😂😂 it looks better
@jsmith8617
5 ай бұрын
That welder sounds perfect for multi passes!!! I set my welder up through sound!!!
@kolumbus1984
4 ай бұрын
Sound like stainless to me.
@v0id852
7 ай бұрын
Slightly too fast you can tell by the ridge in the middle. Other than that looks like some nice arc transfer
@domanikbutler2060
5 ай бұрын
nope
@swampypolitics9574
4 ай бұрын
Yup too high travel.speed, but its still good@domanikbutler2060
@_hector__
4 ай бұрын
@@domanikbutler2060 yes, too high of a travel speed
@allaroundnation6572
6 ай бұрын
Too high of wire speed is causing that spatter and the push and pull technique probably means not enough penetration but the bead looks clean so nice job
@matijaslat2100
3 ай бұрын
not enought wire , not too much what you on about?
@dewayne2189
3 ай бұрын
And something else i do is turn that heat up more to about 25.6 and 300 wire speed and it will lay in there flat and wont have that kinda crown look
@dannybailes3948
11 ай бұрын
They can weld but don’t expect any explanation. This is called fishing for compliments
@fredramos9206
Жыл бұрын
This my technique as well, I call it rattlesnake stringer, best looking ripples!, ....Good job! Thanks for posting., ... Regards from S.TX.
@migstickwelder1992
Жыл бұрын
thank you mate 😃
@fredramos9206
Жыл бұрын
@@migstickwelder1992 Please make it known,..(Rattlesnake Stringer)..... Regards!
@crow2967
Жыл бұрын
@@Crash.7434you’re not ‘supposed’ to do anything there’s multiple techniques. Just cause you were taught one way doesn’t make the other techniques wrong. If you really knew how to weld you’d probably know this
@Undoubtedgrape
Жыл бұрын
@@Crash.7434I use this technique for flux core everyday and always pass UT tests
@nalley6815
Жыл бұрын
@@Crash.7434did you even watch the video? He whipped it, he didn’t just drag it
@VypaGaming
Жыл бұрын
Only do this technique if u know it will blow through the metal. The more back and fourth or looping or some other motion u do apart from the straight pull/push motion, the weld will penetrate less. I guess if u guys really wanna do this, weld on a higher setting so that u can still get good penetration.
@stinkymcstinkerton1854
6 ай бұрын
That makes sense.
@robertblackshear8963
5 ай бұрын
Definitely, this is how I do incerts on ships and it works perfectly on dual shield fluxcore 045/052 wire. I don't know what the hell some of these guys are talking about. All welders don't use the same techniques lol. If you are a first class welder you can weld however you want and get good results. It's easy just read that puddle. I passed all my bend tests whipping especially up and down as I travel along. Shipyards don't care how you weld a joint as long as it's welded properly. If you hate whipping you just hate whipping. I'm glad I never worked on a job that requires me to use a mandatory technique. I probably would have turned it down knowing me because I certainly know my shit with that gun or a stick.
@ButtcheekOnaStick
10 ай бұрын
Love the LOOOONG puddle and inconsistency. Really sells it.
@CrystalLakeLegacy
3 ай бұрын
Ive never understood why ppl think to use a “forward, back and pause” method for short arc mig🤷🏻♂️ that will get u screwed a lot of time in any kind of test(bend or x-ray)…….. I was taught the “forward then pause” method to make sure you are always putting filler metal onto base metal and not running the chance of having cold lap in front of you after you’ve jumped backward……. Forward, back then pause works great for 6010 stick especially on some open root welds but not so much on short arc not filler welds
@kyledelange7055
Жыл бұрын
Spray, nice.
@Markon32191
9 ай бұрын
It's puls Spray have different sounds
@DreamFactories
7 ай бұрын
Spray sounds like you’re blowing blowing air out your mouth
@Ausblack
5 ай бұрын
Watch me whip, watch me fail a weld test
@robertblackshear8963
5 ай бұрын
No bro, I always slightly whip everything. As long as you can read that puddle you pass.
@poweroflistening4184
5 ай бұрын
Your slowwwww that shit has been debunked
@codyshubin1073
4 ай бұрын
That’s wild because I passed all my tests with a whip. I have never done a straight weld with no whip
@Ausblack
4 ай бұрын
You guys never heard of a joke
@user-ck9yo9ek8o
22 күн бұрын
@robertblackshear8963 your welding on top of slag 😂😂
@user-re4ye3df2l
7 ай бұрын
Nice
@antoniomontecillo8739
Ай бұрын
Muy bien aplicada la jente no habla mucho de esta soladura por que no se usa mucho en los trabajos ya la aplique solo para soldar postes de luz
@connormarek1028
10 ай бұрын
I love Spray Arc MIG. I was taught to use a straight push in class, but that stitch makes a great looking bead ;)
@2ItalloSantos
8 ай бұрын
Também estou aprendendo em linha reta
@MrDilley777
17 күн бұрын
I noticed how thick the metal was of the vertical peace and thought the method being used wouldn't achieve enough penatration for any serious load on it😮😊😊
@bgs4896
4 ай бұрын
Nice job keep it up
@jorgecostasilva5033
5 ай бұрын
Que obra de Arte !!! Parabéns
@kylepintor5830
3 ай бұрын
That line down the middle and pointy beads is indicative of running a lil too hot from what i was taught. But nice width. That spray sounds cherry
@Cerkfreeman5451
Жыл бұрын
How years did the guy that adjusted his machine weld?
@WithSherm
Жыл бұрын
It’s called herringbone. It looks pretty good not to much porosity
@jshshshhsjakahdvsh7661
Жыл бұрын
Never heard someone call it that ever in my life
@VypaGaming
6 ай бұрын
Is this an 18mm multirun? Niceee
@dilyandimitrovgoshev3440
4 ай бұрын
Bien...pero te falta mejorar la terminacion...tanto como el comienzo..porque probablemente la prueba de ultrasonido daria fallo al principio y al final..un saludo 👋
@JS-oy6nn
2 күн бұрын
We’re bragging about the easiest welding process there is.
@WeldingCraftsWorld
5 ай бұрын
Nice🎉
@Marcelo20004d
3 ай бұрын
Essa soldar é muito top😮
@lokeshsahu9964
8 ай бұрын
Main bhi co2 weldar hoo
@ScaleBreakerFishing
5 ай бұрын
Really nice
@greg3184
Күн бұрын
Witam ,takie spawanie jest nie zgodne ze sztuka spawalnicza i wprowadza duzo ciepla do spawanego elemetu co nie jest korzystne na odksztalcenia i naprwzenia materialu
@billyrife5809
7 ай бұрын
For y’all who don’t know this method is called spray arc you can whip it where it’s so hot , gotta have least 28-30 volts with 0.45 wire and a argon gas with least 80% or higher for example 80/20 85/15 90/10 95/5
@nathanjohnson3676
6 ай бұрын
That's hot as hell 28-30 Makes sense considering how thick the metal is I guess that would give you good Heat Penetration Thanks for the info 👍
@WooEeePaczeq
5 ай бұрын
The feed is really fast but is it spray? This one sounds *ZzzZzzZzzz* while my machine goes *Sssssssssssssshhhhh* whine spraying. Anyways Big amps and voltage is my kink btw xD
@dedon03
5 ай бұрын
Us old heads know what it is and we also know that that weld will not pass inspection because the machine ain’t set right bad technique and it’s spray like you say. Their is not need to work the puddle.
@dedon03
5 ай бұрын
@@WooEeePaczeq Lincoln’s make that sound. But you are right there wire speed is too high. It’s suppose to sound just like something being sprayed as well.
@billyrife5809
5 ай бұрын
@@dedon03 spray you can whip it and it’ll pass inspection, now dual sheild there’s no manipulation whats so ever
@lovneeshjain409
2 ай бұрын
Can you share the MIG machine setting for this good n clean welding?
@user-lf4iv5fe1d
7 ай бұрын
Назад отвёл и чуть верх, красивей получается
@michaeldvorak5556
11 ай бұрын
It sounds like spray transfer. But, they have the electrode in the weld puddle, which isn't spray transfer. So, what is it? Did some research. It appears to be gas-shielded flux-core (dual shielded) arc welding. Definitely not globular or spray transfer.
@januarylong1107
10 ай бұрын
It is MAG spray arc
@michaeldvorak5556
10 ай бұрын
@januarylong1107 you usually hear the terms MIG or MAG when referring to short-circuit arc welding. Some just say MIG, but with the addition of CO2, which is not a Nobel (non-reactive, inert) gas, they prefer using MAG. As far as spray, no. It's not a spray transfer method.
@OneTequilaTwoTequila
3 ай бұрын
Penetration has left the chat, but as long as it looks like a weld, then it must be good, right?
@bbgame9419
2 ай бұрын
Линия у меня тоже на швах бывает частенько))
@putchagiripj143
8 ай бұрын
Nice bro 👌
@migstickwelder1992
8 ай бұрын
Thanks 🔥
@bambamsilva4557
7 ай бұрын
Top
@drewwallace9219
6 ай бұрын
Better pattern mate you won't get sharp Vs. Whip to front of puddle and cut back into puddle and up. Will get stack of dimes style :) love you
@joekerr168
Жыл бұрын
Very nice chevrons.
@arjunanil2416
Жыл бұрын
Wire speed and voltage ?
@tjbajacustoms8195
11 ай бұрын
tambien quisiera saber
@f.e.oeeorch581
10 ай бұрын
Spray transfer can start at 23-24 volts up to the max the machine can do for 24 volts you can run 550ish on the wire also I think you need up to 80 percent of your gas to be argon and the rest c02
@tippytay8359
Жыл бұрын
I love whippin that puddle like there’s no tom haha used to do circles/weave mig but nah whippin dat hoe is king reminds me of 6010 , whip forward to dig then come back to fill
@Rashevoin78
7 ай бұрын
Во четко ровно , молодец !❤
@user-jn3qd1ob9l
7 ай бұрын
Льёт как молодой, шикарно 👍
@johnchambers1380
5 ай бұрын
Whips on single pass can result in low throat if youre not careful.
@putchagiripj143
8 ай бұрын
Super bro
@migstickwelder1992
8 ай бұрын
Thank you
@ChinoGuey
6 ай бұрын
I’m welding flux core now but damn I miss MIG
@kaelenwhite3609
5 ай бұрын
What are your settings at? I do production mig weld and I weld at 550amps 25.5 volts for most parts.
@MLDIYSH
5 ай бұрын
🤩 what welder do you use? Miller 800? That’s nuts.
@kaelenwhite3609
5 ай бұрын
@@MLDIYSH a Lincoln 550
@MLDIYSH
5 ай бұрын
@@kaelenwhite3609nice. I’m to assume dual shield FCAW?
@kaelenwhite3609
5 ай бұрын
@@MLDIYSH Yes'ir!
@williambailey7825
4 ай бұрын
Firstvtime hearing the correct amperage and wire speed inbthese videos. The buzzing sound is what you want
@user-yo3fn7rv5w
4 ай бұрын
Сварка в импульсе
@jeffbarker3001
5 ай бұрын
Pulse I’m guessing L 59 wire C25 gas? It looks like the root is being done on a lap joint. And the final product is a T joint. Aaaaand he’s riding on the puddle too much I think.
@Transformers1983jd
3 ай бұрын
That would be GMAW-P people. The sound alone gives it away. Bet they are using 90/10 mix.
@stnicholas678
3 ай бұрын
It does sound and look like Spray Transfer, which gives the V look. If that's the case that operator would be using something close to 95/5, with the 5 percent being oxygen.
@Fnhx5ff
5 ай бұрын
Покажи сварочный аппарат
@migstickwelder1992
5 ай бұрын
Ewm phoenix pulse 350
@Laughing_Central638
11 ай бұрын
Love it 😀 😍 ❤️
@filipgrgic8498
6 ай бұрын
Lack of Fusion
@sparkythawelder
Жыл бұрын
I miss that sound
@hooznxt04
14 күн бұрын
Pulse welding
@Shroomytoodope
Ай бұрын
What is volts and wire feed speed please
@SugarKingObi
2 ай бұрын
Nobody talks about mig .
@ryantheoutdoorsmen2536
9 ай бұрын
Looks like my boy is flying, probably slow down a bit. But very consistent, rock on🤙
@hesselbleeker6353
9 ай бұрын
Too fast indeed
@robertblackshear8963
5 ай бұрын
@@hesselbleeker6353Yep just a little.
@migmagelektro
Жыл бұрын
nice
@davidcisneros7621
7 ай бұрын
Whats the machine you're using?
@migstickwelder1992
7 ай бұрын
Ewm phoenix pulse 350
@davidcisneros7621
7 ай бұрын
@@migstickwelder1992 thanks .✌️
@thethicccmint1153
7 ай бұрын
I was told this has more penetration than just dragging it tho it has a higher chance to get poricety
@jimk724
5 ай бұрын
Spray transfer
@user-ce4wg5vq4c
Жыл бұрын
No.bạn chỉ đắp lên 1 số lớp sắt.không tan chảy
@angiemiranda949
2 ай бұрын
Why don't you saw us how to mig 1.5mm tubular😅
@02-Dmitry_21.
5 ай бұрын
Заварил, но подрез оставил.
@danthek5man919
6 ай бұрын
Is that short circuit mig or spray transfer mig?
@agronballhysa9995
Ай бұрын
z20 multipas😊
@dedon03
5 ай бұрын
That right there my friend is a fail. That line going down the middle off the weld face is an indicator you need to work on your technique.
@Adrian-becerra
3 ай бұрын
What kind of wire welding is this?
@migstickwelder1992
3 ай бұрын
Solid wire
@PierreFerraro-ev1ey
Ай бұрын
c'est un MIG /MAG avec un arc pulsé c'est pour ça qu'il y a ce bruit
@bobd.fletcherjr4912
10 ай бұрын
👍👍👍👍👍👍👍👍👍
@paulinorodriguez2180
3 ай бұрын
Dicen que el otro vato pega mes fuerte😂😂😂😂😂😂😂
@m3lon407
5 ай бұрын
All of the end was flat, the edge gonna be lower than the other edge, no way this pass visual check because the edge does not have the same height
@DesertTuna
5 ай бұрын
Beautiful
@Maolat19
9 ай бұрын
what settings of the welding machine?
@markvincentsalandanan5970
4 ай бұрын
What is the amphere and volts measure this?
@kcsmlyngs4975
8 сағат бұрын
Don’t be shy show it from the side now
@user-hg4jw5gv4t
6 ай бұрын
45°
@anakrantauindonesia1470
2 ай бұрын
Keren..
@jamesoneill3445
5 ай бұрын
Wire a bit long
@safwanagha3913
Ай бұрын
رائع
@user-mu7uj5ti1k
5 ай бұрын
left hand welder?
@ejpatrick1950
4 ай бұрын
Whats that line in it mean again?
@WelderFrance
8 ай бұрын
Love it but do more moove so you Will have some Nice fish scale
@migstickwelder1992
8 ай бұрын
Yea , buth when i weld on high amps and not cleaned material i go smaller movement
@AutodidactEngineer
10 ай бұрын
In my area they don't allow mig for materials thicker than 5mm
@robertblackshear8963
5 ай бұрын
And they shouldn't because it's pretty but it will crack like a son of a pitch under extreme stress but dual shielded fluxcore and inner shield fluxcore or stick(7018) can do that thing and withstand stresses. Mig does have its place with thinner material though.
@davidleon770
4 ай бұрын
What are your settings
@JapakUrbanic
4 ай бұрын
How big is the current?
@cameronnicholson1980
4 ай бұрын
Just started welding but my company doesnt allow the forbidden wiggle.
@migstickwelder1992
4 ай бұрын
If u weld for magnet ot rengen test this tipe of welding make lots of problems haha , buth this is classic construction and They ask for B quality welding 😃
@jacktv8487
7 ай бұрын
ampere dan volt berapa ?
@user-om7no8pz6e
5 ай бұрын
Don’t pull back push and hold push and hold
@treyw6882
11 ай бұрын
Sounds like pulse spray almost
@r2dadizubz
7 ай бұрын
Because it is
@sammy6100
3 ай бұрын
Is that a pulse welder ?
@migstickwelder1992
3 ай бұрын
Yes
@sammy6100
3 ай бұрын
Thought so could tell by the sound. Top videos pal
@mtalha786t
11 ай бұрын
👍👍👍👍
@josepacheco9479
5 ай бұрын
“This is not a test, this is fun”
@Dillinfraser-jz6if
Жыл бұрын
Hmm make sure that throat of weld stays good.
@avrgazngamer3661
6 ай бұрын
Bros mig sounds like my grinder 😂
@bonjour145
2 күн бұрын
Trop de fil à mon goût ,trop de vitesses moin de penetration ... sinnon très belle soudure. Amis soudeur 😊
@nosaerjaoi1470
26 күн бұрын
wtf ? since when we weld like this ? push and pull is for welders that cant hold the damn hot glue gun strainght and smooth and can see the undercuts on the top
Пікірлер: 289