I just watched this video sir,but my machine is Emel 20u33,I hope it's procedure is thesame sir,thanks
@belloafeez1911
6 ай бұрын
Please i need this type of machine,how can I get it I'm taking from Nigeria
@patanewshabari9777
3 жыл бұрын
I'm unable to do embroidery with my 20u machine
@jerrykovis5417
2 жыл бұрын
Is 40/2 Polyester okay to use on the 20U33? Read the manual and it says a 40 cotton is okay, but I've read / watched conflicting information. Thanks.
@milanaing3370
3 жыл бұрын
Good day . I used a translator, I apologize in advance if something goes wrong. My question is: can the sewing machine zinger 20U33 (green) embroider the same way as 20u33 Professional (blue)? thank you in advance.
@thuanpham2912
2 ай бұрын
Xỉn lỗi ông chẳng hay ông có bản cái máy này không và cho biết ông đang ở đâu..
@mariaaparecidagomesfernand4038
Жыл бұрын
Quero uma maquina dessa qual o vaĺor?
@egyaackah4769
2 жыл бұрын
What is the use of the knob on the left side of the machine right by the presser foot?
@deserayradziewicz1404
5 жыл бұрын
Can you do a video on threading and using a twin needle with the 20u33, please?
@jamessheehan2694
3 жыл бұрын
you can use two needles? good
@ssergeant9682
3 жыл бұрын
I have a blue one but I think it has the same model # 20-33? where can I get parts or a manual?
@milanaing3370
3 жыл бұрын
Good day . thanks for the lesson. Sorry for the mistakes if there are any, I translate by Google translator. please tell me, I cannot create a zigzag stitch on the Zinger 20u33, the loop is made only on the left side, the thread is not captured on the right side, and as a result I get a straight stitch, I have been suffering for a week now, I bought a machine through second hands thanks in advance
@AlexanderDyer
3 жыл бұрын
Sounds like timing.
@tadstephen8802
8 жыл бұрын
Alex could you make a video of how to set the timing of a 20u33?
@amarachinoelanwachukwu1071
4 жыл бұрын
Pls how do I make I thighter embroidery stich,what's the big notch on top left used for?
@ochukoerefamote3009
4 жыл бұрын
Hi, please help me, my 20U-33 length stiches is not very close...what do I do
@thuanpham2912
2 ай бұрын
Cái máy của tôi cũng giống như mấy của ông nhưng bây giờ đem chỉ dưới lên không được và may không ăn chỉ lam😢 ơn chỉ dùm tôi sửa lại cảm ơn Ông nhiều
@backyardcnc
7 жыл бұрын
Looking at a 20UX143 in minty condition however that version of the 20U lacks the needle position switch, I wonder if you think that is a major issue for general purpose sewing? love the videos! Gerald
@AlexanderDyer
7 жыл бұрын
I think the main use of a needle positioner is in the making of a button hole also the positioner will allow you to sew near the edge of an otherwise wide foot. Good luck in your decision, I hope my modest offering will help some.
@rcolborne4123
6 жыл бұрын
personally I love the needle position switch, great for piping, zippers. I find it just let me get a little closer and easier to keep piping tight. IMHO
@kayaqueen6982
5 жыл бұрын
did that machine have a knee foot lifter ?! if yes i read in their instruction book that you could change the operating of that knee pedal to control the width of stitches instead of foot pressure if so could you please make a video on how to do it please
@AlexanderDyer
5 жыл бұрын
Look at the bottom of the machine. There are two levers that the knee lift can actuate. Adjust your knee lift from one to the other.
@kayaqueen6982
5 жыл бұрын
wow thank you a lot i didn’t know that 👍🏻 i like your channel great work
@anetadziuba4775
8 жыл бұрын
what if i can't get zigzag working just wan to go in straight line ? can u help ? many thanks
@AlexanderDyer
8 жыл бұрын
My car won't run, what is wrong with it?
@beverlyjohnson8490
8 жыл бұрын
You have a great sense of humor. Thank you for this video. I bought the blue version of this machine 20 plus years ago to help out a friend. I need to use it more often. It is a very, very heavy machine. I love going fast. Now to learn how to wind the bobbin.
@rmcdaniel423
5 жыл бұрын
Just bought one of these last weekend. Tough basic machine, and versatile for all sorts of general purpose sewing. It's like my Singer 237 Fashion Mate, if it went to the gym and bulked up. Also this is my first clutch motor. Is it normally really stiff to turn the balance wheel by hand on a clutch machine? It takes what seems like an uncomfortable amount of force, but if I adjust the motor up to loosen the belt tension, it starts to slip at times. Is there some sort of trick to learning to live with the clutch motor or something? I cleaned and oiled it real good, so without the belt on it turns super easy.
@AlexanderDyer
5 жыл бұрын
slightly depress foot pedal to release the brake inside the clutch motor
@rmcdaniel423
Жыл бұрын
Three years later at this point, and this is the primary workhorse in my collection of machines. Very versatile. Love it!!
@level2456
4 жыл бұрын
Hello. Thanks for the video. Can i zig zag soft fabric with this machine? It doesn't seem to work for me 😕
@AlexanderDyer
4 жыл бұрын
Yes but it is a challenge and the machine may need some adjustments to perform well. Feed Dog height and profile should be checked and also foot pressure.
@evanigoncalves9
11 ай бұрын
Gostei preco da maqina
@paulmccomish7250
Жыл бұрын
Have a singer 20u but have been unable to rewind a bobbin I have followed video but still unable to rewind my. I am missing something please help,
@AlexanderDyer
Жыл бұрын
These bobbin winders have a rubber tire inside that only lasts a decade or so depending on use. It is very possible yours needs to be serviced. The top cover comes off and then you can see, remove, replace the tire.
@paulmccomish7250
Жыл бұрын
@@AlexanderDyer thank you.
@teariki58
5 жыл бұрын
What should I do to prevent the machine from getting stuck when a thread remains stuck in the bobbin? Thank you
@AlexanderDyer
5 жыл бұрын
Remove any stuck threads.
@rontailor6783
3 жыл бұрын
Спасибо за хороший обзор.👍👍👍
@waytoparadise8284
6 жыл бұрын
please can you help me how to fix my problem the needle doesn'tmove i think because of the bubbin it have a lot of thread ... or may be the bubin get blocked because of Something else can you please give us an idia how to fix this problem thank you in advance
@AlexanderDyer
6 жыл бұрын
Locking knob on the hand wheel.
@oliviarose6444
4 жыл бұрын
I just bought this machine and I am trying to set it up for free motion embroidery.....the thread keeps breaking ...I cant seem to get the tension correct for free motion... Any advice is appreciated
@AlexanderDyer
4 жыл бұрын
Lots of things can cause thread to break. Rotten thread, misaligned hook, improper threading, improperly set take up lever, operator error, the list goes on. Get good thread, change your needle and start over. Then if that doesn't work turn machine slowly by hand to find what and where the thread breaks.
@oliviarose6444
4 жыл бұрын
Alexander Dyer Thanks so much for taking the time to reply....I will heed your advice..
@oliviarose6444
4 жыл бұрын
I had the needle in backwards..the instruction manual said put the needle in with slot in front....that was the issue...should have had slot in back....duh
@AlexanderDyer
4 жыл бұрын
It happens, sometimes due to issues with the translation of instructions "slot" can get mixed up with "scarf". Glad you figured it out. Sometimes it feels like magic, right?
@ruthkayira1539
7 жыл бұрын
hi. please help me. i just got this machine and my belt is slightly los. how do i adjust it. thanks
@AlexanderDyer
7 жыл бұрын
The motor has an adjustment. Lengthen the adjustment to move the motor down away from the machine and the belt will tighten.
@kofiopoku-acheampong2731
6 жыл бұрын
I bought a new singer 20u but when i release my zig zag adjustment it doesn't snap back like how yours just did and i can hear it click.
@AlexanderDyer
6 жыл бұрын
I'm not sure.🤔
@kofiopoku-acheampong2731
6 жыл бұрын
Alexander Dyer oh ok, Ty
@elizabethfrancois2344
5 жыл бұрын
Hi where i am in trinidad am getting problems to get pressure foot( zipper) i have the green one
@sandrastrathie14
6 жыл бұрын
How do I go about changing the brushes
@AlexanderDyer
6 жыл бұрын
I am not sure I understand your question.
@malikalebbah2321
10 ай бұрын
Svp les explications en français
@zinazina8891
7 жыл бұрын
Je comment reparer zig zag sur singef portative
@evanigoncalves9
11 ай бұрын
Boa tarde
@gessilenedumba9664
6 жыл бұрын
Gostei 😍😍😍 Podia tanto fazer um video em português.
Пікірлер: 57