Thanks for this straight forward build. I'll be keeping this design in mind. .....for both applications of heat and foundry!
@ridwanepribadeeh1997
Жыл бұрын
ALLAAHU AKBAR. SALAM FROM MUSLIM BROTHER IN JAKARTA INDONESIA.
@johnzillner1596
2 жыл бұрын
Without a doubt, the best laid out and executed design of any waste oil furnace/forge/smelter on KZitem. The real clincher though has to be the homemade outriggers at all four wheels.
@dalemiller9444
2 жыл бұрын
Thanks, I did see someone build a similar burner. I couldn’t find screw jacks that would work, so it built my own.
@grassroots9304
Жыл бұрын
Yes, those stabilizers are a nice touch!
@johnkoury1116
Жыл бұрын
Absolutely awesome setup my friend. I have been researching these builds because I am getting ready to do a bunch of castings for parts that are for obsolete engines and equipment. Thank you for the awesome build.
@dalemiller9444
Жыл бұрын
Thanks, you won’t be disappointed with this setup.
@AnthonyCelata
Жыл бұрын
WOW.... Thats a real nice piece of equipment I didnt even hear that lid drag at all. I really want to know how you got that inside lining so perfect. looks like its was some kind of cement mix and you made a mold or something
@dalemiller9444
Жыл бұрын
Thanks, the liner is 3000 degree refractory. It looks and feels like concrete but it can withstand 3000 degrees f. I used a 5 gallon to get the inside form. Works great, I can melt copper, brass and iron with no problem.
@Eisenmann86
Жыл бұрын
Very good idea for fuel burner i like it, 👍👍👍 what is the highest temperature ? can you melt iron ?
@Eisenmann86
Жыл бұрын
check my furnace if you like kzitem.info/news/bejne/xINo0YWpZomqbIY
@73superglide62
2 жыл бұрын
Do you have part on part on the end that gas and oil sprays out of
@philmenzies2477
2 жыл бұрын
Nice job. Did you make the nozzle as well? It looks a bit like a Nudge burner 🤔
@dalemiller9444
2 жыл бұрын
No, the nozzle is a Hago Siphon Nozzle SN 609-8 (.75 GPM) with Hago Adapter, SN 609-56. I think I bought them on Amazon. I did make the spin vain.
@ibercombuss.l.quemadoresin5674
Жыл бұрын
Hello. I am interested to know if you can manufacture this burner in series?
@MaliksGarden
3 жыл бұрын
can we use this in a kiln
@kirkwerner1899
6 ай бұрын
did you make the fan/mixer ?
@NoOneButRonPaul
Жыл бұрын
What's the long red hose/pipe connected to? Compressed air?
@dalemiller9444
Жыл бұрын
Yes, it’s connected to my air compressor located in my shop.
@NoOneButRonPaul
Жыл бұрын
@@dalemiller9444 thank you.
@charles1759
Жыл бұрын
Where do you get fan on end of nozzle
@dalemiller9444
Жыл бұрын
Made it myself out of a large washer.
@charles1759
Жыл бұрын
@@dalemiller9444 what did you cut it with
@charles1759
Жыл бұрын
I have all the other parts but I have been stumped on how to make this. There is another video on here that shows the something like it but doesn't say where he got it. Maybe you could make a video on that
@dukedez1
5 жыл бұрын
That’s a lot of galvanized pipe Be careful with the fumes from that burner.
@dalemiller9444
5 жыл бұрын
Yes, galvanize fumes are hazard. The way this Burner is set up, only the tip get hot. All the heat is inside the foundry. Thanks for your concern.
@nnnnnnnnnick5557
3 жыл бұрын
With how hot thta thing is it'd burn off all that galvinized crud real fast
Пікірлер: 30