Hello support xiaomi FIMI. you have to think that mainly here in Brazil and also in India there are thousands of consumers of your products, I particularly like it a lot, we know that it is not intentional but even so it ends up being unfair to all its consumers who bought a mi drone and continue to acquire where it has stock, because the mi drone despite being older and less advanced than the FIMI x8, it is stronger in climatic situations like wind and has a wonderful and superior stability, please do not abandon the mi drone and consumers who in turn are desperate to think that they will be unable to use it for some time due to lack of battery. please rethink the situation and start manufacturing again, you have the capacity and I believe in creating an update with functions on the mi drone, Brazil strongly hopes for this, consequently it would leverage new sales because we all know of the great quality of the 4K mi drone.
@vagos2511
6 жыл бұрын
Please, add a description!
@tottiroma6059
3 жыл бұрын
Отдать деньги за это чудо, а потом мудохаться с ним при каждом взлёте, это не дрон а недоразумение. Зачем мне столько времени тратить на изучение подобной информации, хочется просто нажать кнопку и полететь, зря потраченные деньги считаю
@Pauldarkfly
6 жыл бұрын
Warning: to use this procedure you must first receive a special FC firmware from FIMI. It does not allow you to fly but allows you to do the calibration (useful for accelerometer error). After calibration ok, to return to fly, FIMI must send the previous Fc Firmware updated on the MI Drone app Recived from FIMI: Six direction calibration guidance 1 Please find a corner with 90 degrees angle for calibration. 2 Put the drone horizontally, turn on the aircraft power and connect to app, do not touch the drone after power on. 3 When the GPS stars on app is 12, put the aircraft upright and lean it on the wall. The drone enters the next direction calibration, and do not touch the aircraft during the calibration. 4 When the GPS stars add one each time, rotate the aircraft 90 degree clockwise and keep it lean on the wall for calibration. Do not touch the aircraft during calibration 5 After you finished the calibration of four directions, the GPS stars is 16, and at this time, make the motor face down, put the back of the aircraft to the ground to do the last direction calibration. 6 When the GPS stars is 21, turn over the aircraft and put it on the ground, the drone will immediately enter the level calibration and do not touch the aircraft 7 When the GPS stars become 21 again, turn off the power and send me email. I will send you a new normal firmware. Do not power on when waiting for firmware.
@step4725
6 жыл бұрын
Paolo good morning, i have a problem with this calibration. I have received a fimi firmware. Installed it correctly and when i turn on the drone with your procedure, it not take nothing. No satellite. I see on the app "gps none", poor precision of gps signal and the lights underneath the drone are flashing. then after 10 minutes the app writes "could take off" but the GPS does not detect any satellite anyway. you can help me in some way. it's as if the internal gps module is dead
@Jackerss74
6 жыл бұрын
im in the same condition. I eceived a 1069 FC Firmware from Mr. Kuang and now i see GPS NONE. I did not wait for ten minute...
@silbernersurfer8264
6 жыл бұрын
May you please tell us whatfor this calibration is? I mean, what is the sense/purpose of this calibration?
@Jackerss74
6 жыл бұрын
o already sold the droe. Adios
@shahnifez
6 жыл бұрын
Can you make video on how to get rid of squeaky noise all mi drones make. i guess every owner of mi drone is pestered by this noise. Thanks
@midrone4349
5 жыл бұрын
all drones makes such sound - more or less. Its the torque change when motors sync to balance the drone. But - are You hovering over Your head only ? go fly a long trip buddy, and ya dont hear that.
@CuriousCatFPV
6 жыл бұрын
We need step by step description.... how did the drone switch on when you inserted the battery ? What do the GPS count numbers mean ?
@kinderkarolkinder
6 жыл бұрын
Radovan Dvorský why should I do this? What is the sense of this calibration?
@EdinelsonBarbosa
6 жыл бұрын
ao meu ver um vídeo feito desta forma não tem nenhuma utilidade, pois não tem nenhuma explicação. to my view a video made this way has no use, because it has no explanation.
@Lugalensi
11 ай бұрын
Hello support xiaomi FIMI, I apologize for my English, I used google translate. I received the first firmware, but to do the 6-sided calibration, does it have to be installed or not? That is, you do the 6-sided calibration work first and then update the firmware (the first one assigned, not the second one after calibration) or Do I first update the firmware on the Mi Drone app and then do the 6-side calibration? I ask because in the video and in the email from FIMI it is not clear what needs to be done first! Thank you
@PSDFILMWORLD
5 жыл бұрын
I bought a mi drone 4k when I was frying the drone the battery was automatically damage And I tried to reset the battery now the drone is showing that the battery has been damage it can't fly anymore, What's the solution to this problem
@rizalhikmatullah3302
6 жыл бұрын
Can you make a video, how to fix gimbal n servo status N/A ?
@scorpawer
3 жыл бұрын
so please tell me what i do with two mi drone machines? without battery because they had problems. I acquired trusting in your quality, but I can't use them without a battery, what do I do? can't I throw it in the trash? nor sell the 2 drones because who would buy a drone that will not fly for lack of battery? At a minimum, it is necessary for consumers to continue using their products. people who bought the mi drone 4K battery precision to continue using it have the common sense to keep battery manufacturing. so that we can buy
@Jackerss74
6 жыл бұрын
i see, during my calibration, drones's led are flashing, slowly, but they doind that. in this video leds are always on.
@jimngugk4741
6 жыл бұрын
Do we really need to do like this when it is first time setup ? or just do It outside the field ?
@VnukovskyiAleksey
4 жыл бұрын
на русском))). если ваш дрон перестал летать и пишет "бедный сигнал GPS" 1) пишем письмо пишем письмо на support.fimi, где указываем номер вашего аккаунта и описываем проблему "poor sigal gps". 2) дожидаемся письмо на ваш e-mail от поддержки компании fimi где вам пишут что на ваш аккаунт направили 6ти осевую калибровку. 3) проводим данную калибровку как на видео. обратите внимание что в конце данного видеодром нужно поставить на рельсы и дождаться пока в телефоне опять появится 21 спутник. после этого выключаем дрон и пишем в поддержку о том что провели в данную калибровку. 4) дожидаемся письмо из поддержки где вам напишут что на ваш аккаунт направили новую прошивку. 5) включаем дрон, через телефон загружается новая прошивка, дрон долго пикает/пиликает. перезагружаем дрон и радуемся! **важно- телефон подключаем по кабелю и важно чтобы на нём был интернет!!! техподдержка может отвечать на ваши письма в рабочие дни примерно на 2й-3й день.
@nevidimuy
3 жыл бұрын
3) В пункте написано что поставить на рельсы нужно. Что вы имели ввиду под этим?
@ahmedvasi-avmphotography8865
5 жыл бұрын
when will u launch mi drone in india
@PaulWingfield
6 жыл бұрын
这看起来非常有用。请给英文翻译。 Zhè kàn qǐlái fēicháng yǒuyòng. Qǐng gěi yīngwén fānyì. This looks very useful. Please give English translation.
@Dan2Mx
6 жыл бұрын
Can you tell me how solved the error of acelerometer and poor gps signal? Thanks
@amirmochtar328
4 жыл бұрын
if i want to re-calibrate again what should i do ? because i turn it on again after step 7.
@Ryan-pg2rw
Жыл бұрын
Hey, I did same. Can you guide me, what did you do? How did you fix it?
@spdrone1412
6 жыл бұрын
"battery damaged cannot be used anymore" How to solve this problem?
@ella-drondecielos1366
6 жыл бұрын
Yo no me e enterado de nada,,,,,ni de qué,,ni de cuando,,,,ni de cómo ni porque?
@technicalgaming4214
4 жыл бұрын
Hi bro haw many you have mi drone please reply
@YuriSerg
2 жыл бұрын
support@fimi.com
@leonardoararas
3 жыл бұрын
ja estou a mais de 4 horas fazendo e refazendo esse procedimento, agora cheguei na ultima etapa onde meu gps não sai do 16, cansei de tentar resolver, esse suporte inútil, estou estudando uns dias e tudo aponta por uma falha na IMU do aparelho vou fazer a troca da peça para tentar resolver esse problema
@macrjh
10 ай бұрын
Como resolveu?
@gabrielneumann6176
10 күн бұрын
Deu certo? O meu está assim, fiquei um tempão tentando resolver e não foi
@va1io
4 жыл бұрын
after you ask for assignment for 6 sides calibration firmware - MAKE SURE YOU LOGIN WITH THE SAME ACCOUNT THAT YOU PROVIDED TO FIMI SUPPORT. ACCOUNT ID is not equal to the email ! if you have provided account id you have to log in with account id in the fimi app!
@dimitargg1
6 жыл бұрын
I have a question Where to buy this IMU Module??? Please advice PLEASE!!!
i would like to HOW enter (in the app) in Six Position Calibration?
@rohitpatelharda9872
4 жыл бұрын
how to connect servo motor to mi drone
@s.bstudio9552
5 жыл бұрын
Sir please tall me on problem only green light open
6 жыл бұрын
I have a gimbal 4k and it does not work right, I have not figured out how to fix it yet. I did the following steps: I fixed the gimbal on the stick and then It does not stabilize and makes two small cracks Also does not turn on the fan The bat led will turn red I tried to stabilize the gimbal with two clicks on the button. It moves, but it does not stabilize. In addition the LED turns blue and then red. The following message appears on the phone: "gimbal stalled protection, please double click mode button or restart gimbal". I did downgrade and did not get it, then I upgraded to 1077 and it also did not work. Even without stabilizing, I can see the image, record videos and take pictures.
@RsproteinPlanet
5 жыл бұрын
Sir, 4k se neeche wala option select kro, And situations 50 se 60 k beech me rakho white balance set krlo Fir dekho full hd video bnega, 4k toh dji me bhi nahi chlta
@Masslenders
5 жыл бұрын
I need more information: The technical support tells me that it has uploaded the firmware to my MI account, but now how do I upload it and install it on the drone? Moreover Do I need the MI DRONE app? do I have to connect my cell phone?
@phamvanviet
6 жыл бұрын
Đang bị gãy chân chán
@thomas3824
6 жыл бұрын
please someone knows the fimi support email ? thank you
@bapu1100
6 жыл бұрын
kuangjinfang@fimi.com
@ИгорьКудрявцев-ъ6х
5 жыл бұрын
Спасибо ! Информация очень помогла!
@bosuxredsux5127
6 жыл бұрын
benefits?
@nevidimuy
3 жыл бұрын
*Надеюсь что поможет! И мой дрон сможет нормально летать* 😌
@manuelnavarro136
6 жыл бұрын
Pongan los pasos porq no se entiende que se tiene que hacer
@metintezcan7951
3 жыл бұрын
For eberybody who asks what is the purpose of this calibration? Should i do this? It is an issue solution and if you request support from Fimi they will sent you a special firmware which is only for this specific calibration process. After calibration you need to request original firmware back for your account again from Fimi. Otherwise this firmware will not allow you to fly. For my case the issue was drone always have warning “low gps precision, cannot take off” even there is 17 setalite connected. Sometimes it was able to fly and once it takes off everything was ok. So i request support also. And now i will try to calibrate hoping for issue to be solved. Wish me luck. :)
@Ryan-pg2rw
Жыл бұрын
Was it solved??
@cyclone71
2 жыл бұрын
send mail fmi , and send this video tutorial for me xiaomi mi drone 4k and no work , not signal gps is in red
@cyclone71
2 жыл бұрын
the GPS stars 21 ,I turned it off and on again and now the gps signal is at 9 it does not go up anymore
@metintezcan7951
3 жыл бұрын
i performed this calibration. And now it is even worse. İ cannot fly.
@dathewborlyngdoh4681
2 жыл бұрын
Me too.... did you solve the problem?
@metintezcan7951
2 жыл бұрын
@@dathewborlyngdoh4681 Nope. I wısh I had never tried that.
@dathewborlyngdoh4681
2 жыл бұрын
@@metintezcan7951 in my case.. i ask from the support team for the previous firmware (before 6 side calibration) now i can fly the drone but camera is still not working.
@YuriSerg
2 жыл бұрын
@@dathewborlyngdoh4681 Check your SD card (they call it TF, you probably have a note on screen ""NO TF")
@vijaysamrat2190
6 жыл бұрын
my mi drone not recording videos and display gimble not detected but flying and show the video in mobile in tha place of camera show N/A
@Jackerss74
6 жыл бұрын
beause your imu module is damage: it.aliexpress.com/item/Feiyu-SPG-SPG-Live-SPG-Plus-MG-Lite-MG-V2-G5-stabilizer-Bluetooth-remote-control/32827690765.html?spm=a2g0y.search0104.3.65.69d74ecbNaaPgm&ws_ab_test=searchweb0_0,searchweb201602_1_10152_10151_10065_10344_10068_10342_10325_10546_10343_10340_10548_10341_10696_10084_10083_10618_5723411_10304_10307_10820_10843_10059_100031_10103_10624_10623_10622_10621_10620,searchweb201603_6,ppcSwitch_5&algo_expid=d3785a18-4614-4eb9-9306-5357d553d4d9-9&algo_pvid=d3785a18-4614-4eb9-9306-5357d553d4d9&priceBeautifyAB=0
Пікірлер: 63