Pretty impressive. Some very nice engineering (brains) behind those designs. Especially considering it's a "over the counter - commercial" product. Somebody was really thinking. Good job!
@rickytyson8778
3 жыл бұрын
Instablaster.
@t.j2881
5 жыл бұрын
I have a pro series manifold on my H22 and it's been a fucking nightmare... The fuel rail studs would shear off in the manifold while driving and rail pressure would start pushing fuel past the injectors.. Left me on the side of the road more than I'd like to admit. It turned into a regular occurrence. They'd shear off, I'd tap them out, get new studs & spacers, install them, they'd shear again in a matter of weeks. I even started adding 2 zip-ties to hold the rail down every time I'd replace the studs and spacers because I knew they just break again.. the zip ties would atleast keep the rail in place long enough to get me home and stop a potential fuel leak. Eventually I ditched the studs for grade 8 Allen bolts, I thought I had it fixed and figured i didnt need the zip ties anymore. I was wrong. The last time it happened my car actually caught fire on the side of the road at 3 am, cell phone was dead, closest house was a good 10 minutes walk.. luckily I managed to put out the fire under the hood by smothering it with my sweater, pushed my car backwards then put out the second fire burning underneath the car. No damage to the car other than a slightly crispy harness. After that I decided enough was enough, I took the manifold off and brought it to a local machine shop. They made some spacers out of aluminum, drilled and tapped them out for a much larger Allen bolt and welded them to the manifold. No problems since. Only downside to this is I can now only use injectors that are the same height as obd1/obd2 honda injectors since I dont have the option of using a shorter spacer, no big deal really... After all this I really do think it's a big fuck up on skunk2's design of this particular manifold. For some reason they decided to tap the hole for the rail studs on the very edge of the mounting base, when you install the studs then put the spacers over the stud, the spacer hangs off the back of mounting base. Its offset from the base. Even the machine shop who I had fix it pointed this out as a major shear point. If you own a pro series manifold for an H22 take a look and you'll see what I mean. I've looked at their B and K series manifolds and they dont have this problem, stud holes are right in the center of the mounting base, as they should be. Its almost like they didnt bother to fix the design after it was put into production or they never even bothered to look. I emailed skunk2 to inform them of the issues I was having, I even sent links to hondatech pages of people having similar issues with this manifold. Eventually they just started ignoring my emails, big surprise..
@WilbertRamos777
8 жыл бұрын
I have the street ultra wit a 70mm skunk2 pro TB & skunk2 stage 2 cams on a fully built b18c1 & so far it works 100%
@hondapowereg6002
8 жыл бұрын
+Wilbert Ramos hey did you put the thermal casket on it or did you put a stock one??
@WilbertRamos777
8 жыл бұрын
hondapower eg no I bought the thermal gasket better stock is to thin
@jamesnewton8164
3 жыл бұрын
Wish you made the ultra series for the h22a
@AllMotorGarage907
4 жыл бұрын
How you gonna say often imitated when that manifold is literally an imitation of the factory CTR/ITR manifold 🤔
@averyalexander2303
4 жыл бұрын
True. LOL
@Itr-tv7kt
4 жыл бұрын
i wanna buy one of these manifold.. im thinking the ultra street... would you say that's a good choice for my setup? it is n/a.. some aggressive cams and slightly higher compression ratio than stock. its making around 220 whp. im going to keep it n/a for now and what size throttle body is good for n/a ?? thanks
@henryrosado1549
3 жыл бұрын
What is the flow difference between a ultra street and the race manifold?
@beethao5578
10 жыл бұрын
u guys should make a new pro series manifold detachable itb that u can separates it . for example if u like the whole thing u can just leave it on or want more power take the other half off so it will be itb to make more power
@beethao5578
10 жыл бұрын
for the d16 civic
@bigpimpin9124
4 жыл бұрын
Do u have anything for 9th gen Honda Accord please let me know?
@kdotktimetopurge8549
7 жыл бұрын
some one said on pro skunk 2 to use that on b18c4 u have to block off pipes to run it
@SeptemberSeptumis
7 ай бұрын
Good question. Is the base model. CARB legal?
@pebblez_
6 жыл бұрын
Did he said "all motor"? I want dat 1
@melody3741
7 жыл бұрын
why dont u just cast them already ported?
@pacific7775
5 жыл бұрын
Not everyone needs em ported ..
@averyalexander2303
4 жыл бұрын
As someone else said not everyone needs them ported and larger runners could be detrimental depending on the setup. They could polish the runners after casting though, that wouldn't hurt.
@hondas8447
9 жыл бұрын
Is the skunk2 intake manifold the first one you talk about , is it loud as the stock one or much louder ? Including alpha 70min throttle body . I'm planing to buy one
@johnellanderson8704
8 жыл бұрын
would the ulrra series manifold fit my 02 rsx ??
@leroyjenkins1725
9 жыл бұрын
if I bought a Pro Series manifold when I have to get new injectors
@zsakosbimbo4383
8 жыл бұрын
So my question is if i go for 300hp with b20 on the bottom and b18 head is it enough to use ultra race Street intake manifold or should I have to use the ultra race intake manifold system??
@damitriedamitrie6690
7 жыл бұрын
Hmmmm I think the blox itr rep was pretty nice
@xxconnxiong5303
6 жыл бұрын
Do you have a skunk2 ultra intake for a h series
@13ANDR3W
10 жыл бұрын
go over the skunk2 camshafts
@cheeseburguhgaming9581
Жыл бұрын
Will the ultra street manifold work on a Stock b18ls or stop b20 head?
@Jaysmaccin
10 жыл бұрын
Suspension next !
@danielrios290
3 жыл бұрын
Does a d16a6 motor fit a skunk 2 manifold pro series
@kdotktimetopurge8549
8 жыл бұрын
hi do u have any vid of put them on the the b18 lumps and do u have to run the catch can on the gsr in let
@patrickjohnson9629
7 жыл бұрын
Which is better for low end torque?
@truefirebbq9444
9 жыл бұрын
Very cool.
@massoncordero963
7 жыл бұрын
Im thinking about getting the ultra street racing intack manifold and was wondering if it will fit my acura tsx 07 with the k24a2 motor
@vandettabuilds6641
5 жыл бұрын
Do you make a manifold for the 2.7 Porsche 944 NA ?
@k1ngswift
9 жыл бұрын
Will an 1998 Acura Integra Intake Manifold fit a 1998 Honda CRV
@numberpirate
8 жыл бұрын
+Swiftness_ Assuming it is a B18A or B18B yes it will. A GSR B18C1 will not fit as they have different bolt patterns and the B18A&B and B20B&Z do not have dual path intake runners.
@victorargueta4560
7 жыл бұрын
Will the race manifold still have a port for the idle valve? Or no?
@PedroRodriguez-fz3nd
5 жыл бұрын
Would the Ultra series race manifold be good for an all motor build?
@illestk24civic
8 жыл бұрын
Counting in millimeters, this is America!!!
@electricfeel9501
8 жыл бұрын
In america mm is still used. Tools are in mm. MM is used in engineering too...
@DevasionX
7 жыл бұрын
Metric is superior
@hectorae86
7 жыл бұрын
Dear Skunk2.... please make Toyota stuff.
@dryheat3633
7 жыл бұрын
hectorae86 buy a civic
@Itr-tv7kt
4 жыл бұрын
buy a honda :D
@nepzski
2 жыл бұрын
will you guys ever sell turbos?
@pabloguerrero7752
10 жыл бұрын
Will there be one made to fit Ls /b20 none vtec ?
@toddmalone1980
9 жыл бұрын
Is one in production for the FRS/BRZ twins? If not get on it lol...... if so when would it be released? My Skunk headers and power box intake are lonely......
@luiszayas15
4 жыл бұрын
Can I used it on a non vtec b18 head
@dimitriseals4389
6 жыл бұрын
Acura/Honda only?
@MrRiddimmonkey
10 жыл бұрын
Which one can I use on my K20z2?
@moggel6
10 жыл бұрын
Could you do this for the d series
@channingkelso7339
10 жыл бұрын
they only have the first one they showed, I own a y8 and its pretty pointless to have one unless its built and boosted.
@MexhomieXlll
9 жыл бұрын
Channing Kelso its not pointless. Gain is gain
@MexhomieXlll
9 жыл бұрын
Channing Kelso plus you wouldnt use a pre series mani for a turbo y8 you would get the ultra or race series manifolds.
@channingkelso7339
9 жыл бұрын
when the product is 250$ or more and you only gain 5hp.... a gain isn't a gain. they don't make them for the d series.....
@keenanwalker1313
7 жыл бұрын
Channing Kelso doesn't mean they won't work for d series engines bruh. Also it's not just about an HP number it's about shifting the power band and making more usable power where u need it . Throwing out numbers like a"5hp gain" is bullshit depends on the build ... JS
@LuisF777
4 жыл бұрын
Is the ultra street fit k24z7 ?
@adeelhassan4652
8 жыл бұрын
How much HP and torque (at Max) a pro Manifold can add to a D16 engine??
@MElekiaZ
7 жыл бұрын
3-7hp
@pedromurillo3654
7 жыл бұрын
Adeel Hassan ujj
@ramennoodleshaawty
6 жыл бұрын
Go hunt for a b series engine at a junkyard for 200 bucks
@vi_EviL_iv
7 жыл бұрын
Im confused, you say in your video that the pro series its CARB legal #307-05-0325 but I've been told its not. Part #307-05-0600 (street version) says its CARB legal. Both version fits the engine but Part# 307-05-0600 doesn't fit engine bay in the 2004-2008 Acura TSX. Please confirm.
@timm5970
5 жыл бұрын
Hes showing intake manifolds for a bseries and you are looking for an intake manifold for a k series
@ardhikagmv
7 жыл бұрын
i like this.# from lombok
@ortiz75
7 жыл бұрын
I have a Skunk2 Aplha 64mm throttle body, can I use it with the Ultra Street manifold?
@fish_on_gang1436
3 жыл бұрын
Min of 68mm is recommended
@pacific7775
5 жыл бұрын
You send me a seconds ultra street for my k20/k24 and i wont shut up about tellin the world how great skunk 2 is ...and ... il be your best friend .we got a deal ??
@adrianarteaga6275
7 жыл бұрын
can you use the ultra intake manifold without the top??
@nathaaab
7 жыл бұрын
No, but you can put Individual Throttle bodies instead
@Built_it_by-alex
9 жыл бұрын
do u guys have ITB's?
@averyalexander2303
7 жыл бұрын
Why get a spacer? Why does the amount of air it holds matter?
@sven7639
7 жыл бұрын
Because physics
@riteshnayak80
7 жыл бұрын
A DIY Computer Guy Increases plenum volume...which is a sort of buffer air pocket which will come handy especially in all motor application for better WOT response.
@1CFLOW3
10 жыл бұрын
Can these work with a k24z7?? 2013 si sedan?????
@channingkelso7339
10 жыл бұрын
they make them for all the k's
@trumpetplyrmatt
7 жыл бұрын
BOOSTED_FB6 yes you need the PRL Motorsports adapter..kinda like using the RBC manifold
@panteraismetalful
8 жыл бұрын
That kseries pro manifold is complete shit and i have the pics to prove it. Numerous dyno testings over the years of sub rbc manifold performance. Thanks for finally putting out something that works, 4P will perfect it
@zero-fg1012
3 жыл бұрын
Got this on and the car wouldnt start
@randysd4211
7 жыл бұрын
do u guys sell manifolds on ebay? or amazon?
@randysd4211
7 жыл бұрын
or Amazon?
@hubbardhurlston5926
2 жыл бұрын
Ok I don't really understand thats why I watch the video
@REXVTEC
8 жыл бұрын
the ultra series is nice to b16?or b18 NA?
@chrsst916
10 жыл бұрын
Wheres the F23 manifold? Oh wait yall make next to nothing for accords, thats right
@jacobalbarez6153
9 жыл бұрын
Lol that sucks.
@kdotktimetopurge8549
8 жыл бұрын
hi do u have any vid of put them on the the b18 lumps and do u have to run the catch can on the gsr in let
Пікірлер: 89