This is very poor job of re-sleeving a cylinder head, the actual process is very different bcz it involves heating the cylinder and shrinking the sleeve with cold it takes a precise amount of calculation and almost ration of heat and cold for re sleeving cylinder and perform effectively.
@ramshadr6927
2 жыл бұрын
Absolutely
@vnsworkshop9961
2 жыл бұрын
Nooooooo You must warm the cilynder and male the sleeve col. Than it will go inside with free play to align. In just 5 second than you align the port.. Why this people don t sue the head...
@tscooter8103
2 жыл бұрын
OMG No! No! that sleeve is so loose it will not be able to dissipate its heat to the cylinder for cooling, and the worst is that sleeve will "Walk" and push out the head gasket. please nobody do this its a hack butcher job. great installation information can be had from either LA Sleeve or my boys at Advanced sleeve around the corner.
@rahulgumber3718
4 жыл бұрын
Nice work
@javithu6
3 жыл бұрын
சூப்பர் bro
@Srivishnutejas
2 жыл бұрын
Thank you 💛
@muthumuthu3426
3 жыл бұрын
Super
@szymoozz
3 жыл бұрын
Ahh the good old swing press
@ashishpatpingua4015
4 жыл бұрын
Ekdum badiya bro 👌👌👍
@desmondlloyd7568
3 жыл бұрын
Wrong method.fitment also loose
@outdoorbikingbrothers5223
3 жыл бұрын
Where is this shop?
@darklence8784
4 жыл бұрын
എന്ത് തേങ്ങാ ആണ് ചെയ്യുന്നേ ഇങ്ങനെ ആണോ sleeve ചെയ്യുന്നേ. അപ്പോൾ കുറെ കാലം കിടക്കും.
@vickysvlog3830
4 жыл бұрын
Evolavu Aachi bro How much cost bro
@cselvaraj3128
2 жыл бұрын
Bro Yamaha RX100 bike la sleved and unsleved yaepadi kandu pudikaradhu konjam busy. Very urgent.
@srisundar7890
2 жыл бұрын
Bore ulla porting pannirukanu pakanum bro
@rashmiranjansahoo7822
2 жыл бұрын
Once sleev is last over size what's next Can i use that block or not
@gaurakshak_saurav
Жыл бұрын
not
@manojkumardme4526
8 ай бұрын
Price
@vintage.vibees
2 жыл бұрын
Suzuki shaolin cyinder port pannuma ?
@srisundar7890
2 жыл бұрын
No sir sleeve not available ...
@neerajmalhotra9585
3 жыл бұрын
Bhaiya apna shop ka address batao
@Creatives-World
4 жыл бұрын
Sleeve installation kay baad kesi performance hoti hy RX115 ys 135 ki. Kuch loog kehtay hein 2stroke mein sleeve successful nahi rehti pick aur power mein faraq aajata hy. Aur piston bhi seize hota hy
@rishigovekar1419
3 жыл бұрын
Port matching ho toh kuch problem nahi hoti hai
@urvish6649
2 жыл бұрын
@@rishigovekar1419 right
@boymarbs8860
4 ай бұрын
@@rishigovekar1419yes a 💯 right
@akibkumbari3790
4 жыл бұрын
Tell us what's standard size and sleeve size
@Deepakgs-bu6mx
3 жыл бұрын
0.25 mm bro
@akibkumbari3790
3 жыл бұрын
@@Deepakgs-bu6mx if in micrometre it says 50.23mm then till what size ull do honing
@Deepakgs-bu6mx
3 жыл бұрын
@@akibkumbari3790 the next size will be 0.75
@akibkumbari3790
3 жыл бұрын
@@Deepakgs-bu6mx bhai agar 50 mm ka block size hai n oversize piston 0.25mm ka hai to aap isko kitta boring n honing karoge
@Deepakgs-bu6mx
3 жыл бұрын
@@akibkumbari3790 bhai standard size hai 0.25 agar honing karoge toh next piston size apko market mai 0.50 hoga
@ailumallannakolupula4397
3 жыл бұрын
Yamaha new bike 2002 chahiye kallu
@sahilpatil7418
Жыл бұрын
How much it does cost
@surajliferocks
11 ай бұрын
Sleev cost 1500
@boymarbs8860
4 ай бұрын
@@surajliferocks I want to put new sleeve on my 5speed block It will be alright?
@mananchaudhary1326
4 жыл бұрын
Bro can you tell me what is the procedure of removing an old sleeve
@danieldzvonik9164
3 жыл бұрын
heat it up in a oven and carefully tap it out with a block of wood
@rsjeyaram3030
2 жыл бұрын
bro ethu avlo price bro sollunga en bike ku change pannanum
@srisundar7890
2 жыл бұрын
3800
@Abhi_kahar_1627
2 жыл бұрын
Successful hota hai kya ye sleeve rx135 mei
@vikasmishra8150
2 жыл бұрын
Ha bhai sahi tarike se hoga to acha kam karta hai...original jaisa to nahi lekin dum hota hai
Пікірлер: 63