Emotions harm business. Emotions are not bad, but very dangerous.
@MrFrezeeTr
3 жыл бұрын
Tears dropping from my eyes while watching it :'(
@yanyanyan25
2 жыл бұрын
And soothing, calming and relaxing.
@electronicscaos
2 жыл бұрын
Everyone must agree that it is way better than that annoying beats in viral diy videos.
@vrushabhmaral7759
Жыл бұрын
If you really loves work , then Brain will release good dopamine 😊 good presentation 🎉
@popiyag
5 жыл бұрын
This method looks very easy. But practically it is not. Usually we happen to do this kind of work as a rework. There are many parts already installed nearby. Here there are no other parts, no pads connected to ground. The thermal pad of the chip was ignored. And the board appears to be a double sided (two copper layers) only. When it comes to a board of eight ten layers with heavy density of copper and several pads connects to ground , picture is completely different. We have to use a hot plate to preheat, under the cradle, which holds the board and place everything under the microscope. Then we have to perform the soldering as in the video, sometimes with the help of hot air gun. Everything should be done very carefully, taking care not to burn any connector or part because under the microscope we can see very limited area only. When we perform our duty very carefully, the worst thing is our employer used to bring his laptop to show us these type of videos and points us " See , how quickly the youtubers do this."!!!!!!!!!!!
@vasiavasin5180
5 жыл бұрын
вот и хуй-то!!!а автору похуй на это!......и это,я бы слал на хуй таких клиентов!!!
@NicolaiSyvertsen
5 жыл бұрын
For hobbyist projects you make sure to make PCB designs that make manual assembly easier. You don't use the smallest pitch ICs or 0603 passives etc. And chips like these are often soldered with solder paste and hot air.
@ManishKumarIITG
5 жыл бұрын
Next time your employer says so, ask him to hire the youtuber.
@aaliyahagwan
4 жыл бұрын
@@NicolaiSyvertsen Yes
@aaliyahagwan
4 жыл бұрын
@@ManishKumarIITG 😂😂😂
@RicardoOliveiraRGB
5 жыл бұрын
The tears that will drop from my eyes by watching this video will wreck all my soldering
@JoseGustavoAbreuMurta
3 жыл бұрын
I managed to weld a 0.5mm QFN 28. I learned with you. Perfect! Thank you very much!
@Virtu0city
6 жыл бұрын
Two o'clock, middle of the night and I’m watching some random dude soldering... Good night
@siriokds
3 жыл бұрын
The same, at 3am. Two years later in the middle of pandemia.
@zoraamethyst2147
3 жыл бұрын
3 am and us
@Davidocka
3 жыл бұрын
Same but in 2021
@freemasonry666
3 жыл бұрын
3:25 am
@alexm7056
4 жыл бұрын
This method only works well for a footprint designed for "handsoldering" with iron. That is why pads on breakout board are long enough so it is easier to get heat transfer with regular soldering iron tip.
@MeepMu
3 жыл бұрын
I've never seen something so beautiful in my life!
@hansfritz7827
4 жыл бұрын
Dont forget the power pad under the part, you need hot air to mangage to that :)
@klazzera
3 ай бұрын
it can also be achieved with soldering iron from below since there is thermal connection
@user-wh9um7bl4w
4 жыл бұрын
Damn... the music makes it soooo refreshing
@samuelgonzalez317
5 жыл бұрын
Dude, you make this look like art
@richardsilva-spokane3436
3 жыл бұрын
Excellent macro photography and editing. Perfect soldering technique 👍👍👍👍👍
@Pixell_Eletronica
4 жыл бұрын
Perfeito! Eh gratificante e relaxante ver um trabalho assim bem feito
@martinwashington3152
6 жыл бұрын
Thanks for making this video, I'm getting in to SMD/SMT boards myself and this video was very well presented and explained :) I'll subscribe :D
@briandelgado3726
4 жыл бұрын
Tut tut 6⁵⁵33 a eoyeruyuey3y3ygggegertgrte tree teddy toy tree
@janbalga7702
4 жыл бұрын
Very nice work. Great close-up.
@j.lietka9406
2 жыл бұрын
Still came out clean and perfect!
@e.w.2396
4 жыл бұрын
Simply the best !!! 👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻
@nikolaykalinin3395
5 жыл бұрын
Прекрасная пайка,очень аккуратно и с умом!
@weinickchan
6 жыл бұрын
i like your confidence anchoring the second spot without checking if there is any misalignment..
@elcomentador2408
6 жыл бұрын
Nice video, like the music.
@izzyblackout1090
6 жыл бұрын
epic skill. thank you for the tutorial
@serviciotecnicotab3115
Жыл бұрын
MUY BUENOS TUS VIDEOS GENIO NOS INSPIRA A TODOS LOS QUE HACEMOS ESTO SALUDOS DESDE ARGENTINA
@shost58
6 жыл бұрын
not good, need thermo fan for soldering central thermopad chip
@marciosouza5864
4 жыл бұрын
Muito bom seu trabalho, deixo aqui saudação do Brasil.
4 жыл бұрын
Very professional, excelent work
@nheng6913
2 жыл бұрын
Nice video, love the wave effect. It's so easy on boards without ground planes and on leaded solder though. And no thermal pad. Can be a living hell without preheater on bottom and proper temperatures/times.
@r3montickplay951
5 жыл бұрын
Great Job !!! Thanks for the cognitive Video =)
@fadifadi-4u
4 жыл бұрын
Beautifull work!!!
@branieffpulido
3 жыл бұрын
If there was a reaction of I love it on youtube I would put it ... that work so neat and perfect I loved it
@antunesmatias
6 жыл бұрын
Great job!!
@The.Ordinary.People
6 жыл бұрын
I think there is a big issue, no solder on the ground/central pad if it's necessary.
@mikaelkalki3171
3 жыл бұрын
This is such a beautiful video
@WhatAWondWorld
3 жыл бұрын
Красиво! Спасибо!
@LexBedneyDr80
5 жыл бұрын
Super sprawa szybko i dokladnie
@kynkai
6 жыл бұрын
this is so satisfying
@revenger9900
5 жыл бұрын
True😋
@bidz1947
5 жыл бұрын
Concur. Most therapeutic... N relaxing I find when replacing large SMD ICs.
@matthewpeterson5159
3 жыл бұрын
watching this makes me ask myself why I waited so long to get into SMD (as a hobbyist)
@tonyennis1787
3 жыл бұрын
Be prepared to practice for a long time.
@KaiDon1
5 жыл бұрын
I enjoy listening to the backgrond music.... very relax.
@Majidmohamod
5 жыл бұрын
Me too, you can find it here kzitem.info/news/bejne/0X1906ycimugdaQ
@luisradiotecnico307
6 жыл бұрын
gracias, esos detalles al soldar microchips no lo sabia...
@oskimac
5 жыл бұрын
the saddest qfn soldering video... :-(
@MarioMartinez-vl4wf
5 жыл бұрын
when said "unfortunately solder mask damaged..." plus the music, I almost cried
@berembah
4 жыл бұрын
They use the video plot in latest movie, really sad. The move title I think "You beautiful feet shower my lip"
@user-hx4ri4cs4x
Жыл бұрын
Отличная работа👍
@chinthakasandamal8283
4 жыл бұрын
Super smooth
@mohamadaldarwish6678
4 жыл бұрын
Professional 😍👍
@UedersonThec
6 жыл бұрын
Very good! Trabalho muito bom!
@MovilOne
4 жыл бұрын
Good! 👍
@SoorajGopakumar
6 жыл бұрын
That was nicely done!! What magnifier do you use?
@ok-eh7zm
10 ай бұрын
you make it look so easy
@elbakkali
3 жыл бұрын
Thanks for making this video super my friend
@ToDie4r
3 жыл бұрын
I like to use how air for this especially because most IC have middle large contact for ground or for heat dissipation and i like to solder that too.
@johnsim3722
6 жыл бұрын
The advantage you have here is the large pads to allow you to use a relatively large tip when soldering. It's sucking the solder up from the joint. Problem is that when you follow the manufacture's footprint guide you get minimal area. In production thankfully I'm using a stencil and a convection oven. But sometimes I do need to rework these devices and what I do isn't too dissimilar to this video. Using a large chisel tip iron, lots of flux (liquid rather than paste) and make a big blob of solder to be dragged along the side of the IC. Replacing these ICs you need hot air. What I've also found is that with ICs that have a large thermal pad you also need to add a heater underneath the board. Set it to 100 / 150C so that your hot air has less work to do. You'll do less damage, or none at all, this way! Replacing just carefully put down some solder paste, you don't need much, and then again back to the hot air. But they really are an absolute pain these packages!
@omarquispe4556
5 жыл бұрын
I u u
@cris101879
5 жыл бұрын
77ii
@Ozzy3333333
5 жыл бұрын
QFN are a breese, csp even easier, what is tough is the new 56 Gbaud packages.
@hugepines3990
4 жыл бұрын
@@Ozzy3333333 BGA1156 ;P
@Ozzy3333333
4 жыл бұрын
@@hugepines3990 We now have 60x60mm 3488 pad packages (80amps), these need everything correct to get them working. I still believe the 56 Gbaud are the hardest, everything needs to be perfect.
@inlasttonowhere4459
4 жыл бұрын
Thank you, cool skills
@HOLLYWOODlosANGELES
4 жыл бұрын
*C'est bien présenté, j'ai compris maintenant comment souder ce type de composants. Merci*
@user-dw9ep9fe6e
5 жыл бұрын
Просмотрев видео вспомнил ролик где чувак говорил это просто охуеный зум 🤣
@hightttech
4 жыл бұрын
Nice camerawork.
@sergeydanilin5204
5 жыл бұрын
Если так на печатке запаять - не сложно. Плюс брюхо не пропаяно. Я паяю так: аккуратно залуживаю посадочное место и чип. На чипе должны получиться бугорки на выводах. Совмещаю чип и посадочное место. Грею феном до момента посадки. Проверяю микроскопом правильность посадки.
@bond3751
5 жыл бұрын
Хорошая работа.
@UCanDo
3 жыл бұрын
Какой микроскоп вы используете?
@tarekfiliachi6350
5 жыл бұрын
NICE SOLDERING AND VIDEO.
@sophon1999
5 жыл бұрын
มาเป็น Fc sub ใหม่ครับ
@gettingamazing
4 жыл бұрын
Good and perfect skill ever,
@profissaoglobal2
4 ай бұрын
Really impressive
@rodrigodeoliveira4015
6 жыл бұрын
Excelente
@viptech5039
5 жыл бұрын
Clean work good
@DreamElectrical
6 жыл бұрын
Nice work
@oliverisailovic
5 жыл бұрын
Nice video and beautiful music :) Thanks!
@haziqhatta2411
5 жыл бұрын
Great Vid !
@redchili6349
6 жыл бұрын
amazing..
@bjl1000
6 жыл бұрын
for the central ground pad , I would put solder in the hole , from the bottom and heat the pad through the hole with my soldering iron.
@kamleshpanchal5391
2 жыл бұрын
very useful video - thanks
@user-pk7gp9cf3e
Жыл бұрын
У этой микросхемы должно ещё припаиваться пузо, поэтому - термофен. Нужно облудить все контакты до пайки. То, что ты показал - конечный этап для контроля посадки микросхемы.
@tforgo
6 жыл бұрын
Great footage quality. I would aprecheate voice over music. Explaining stuff, pros and cons. Etc.
@burntable
2 жыл бұрын
2:34 thanks for keeping it real!
@alireza98325
5 жыл бұрын
well done!
@klazzera
3 ай бұрын
what a great skill
@TuncayKandemir
5 жыл бұрын
nice job thank you
@gavincurtis
5 жыл бұрын
I see this particular package type causing a lot of cold solder failures in equipment we repair. Seems that the TQFP packages are better as their actual leads are more capable of dealing with thermal expansion?
@coldplayer6268
3 жыл бұрын
This is art
@jasonmorgan661
3 жыл бұрын
Theres that damb toothpic and same can of flux....😌 love it lol.😃
@TubeLightDiscover
4 жыл бұрын
I have same smd soldering process using iron box method simple and easy to use .
@mhwong1865
2 жыл бұрын
You forgot to solder the thermopad/GND Pad that located underneath the chip ,which may be very important for the performance of chip align with the specification.. when soldering QFN with thermopad . hot air soldering and drag soldering method shall be applied
@robin_dong
6 жыл бұрын
Use flux to fix the QFN-chip looks like a good idea. I will try this method later.
@masprassaja3818
5 жыл бұрын
So satisfying, next buy flux. :)
@papilyon
5 жыл бұрын
music so beautiful
@mattlanderclairzil7316
4 жыл бұрын
Goog work bro..
@AThreeDogNight
6 жыл бұрын
You make this look really easy although I know that it is not, especially with a soldering iron. You must have done this for quite a while now.
@michaelschecker2716
5 жыл бұрын
I solder QFN with hot air in 1/100 of the time. The best moment is when the QFN allign itself.
@peterjensen3162
4 жыл бұрын
Please show 🧐
@carrotspell
6 жыл бұрын
i am crying when i see what you do
@shifty2755
5 жыл бұрын
He's not THAT bad.
@ivsongold322
5 жыл бұрын
Top 10 o serviço 👍
@babumanikuttan2258
2 жыл бұрын
Nice video
@e-tech4781
3 жыл бұрын
good soldering
@mineown1861
5 жыл бұрын
Where did you get that metal siphon you had on top of the alcohol bottle ?
@ptaszor9779
5 жыл бұрын
Magnificent, dreadful and sad at the same time.
@EletroLaix
6 жыл бұрын
what camera do you use for filming?
@TheHtc3d
5 жыл бұрын
Чистая работа!)
@Luiselraro27
5 жыл бұрын
Es bellísimo......
@diadificil214
5 жыл бұрын
Esse cara é fera
@htd7814
4 жыл бұрын
Hello ! What kind of camera do you use to record videos? Verry clear image. Thank you
@RahulElectronicspoint
4 жыл бұрын
Nice video sir
@katsuyukihamamoto
5 жыл бұрын
最初の位置決めが一番大事ですね~
@kobtcom
4 жыл бұрын
the ground under chip is not solder. so effect to chip high temp. and unstable work
@TheBypasser
6 жыл бұрын
Neat, but not a QFN soldering you expect :) The "real" one is not much harder though, the main difference is you also have to tin the package terminals to get the same pillow shape as you got on the PCB pads. And better use a blowtorch with a catalytic nozzle as advised in some (can't recall which one exactly) repair note instead of hot air gun, makes things way easier as nothing gets blown off.
@dickdon2631
4 жыл бұрын
What a piece of work, Good! But can you show us your soldering iron brand and tin brand, work station brand, and Microscope, etc....
Пікірлер: 539