Solo Levelling resin dagger
Difficulty:
★★★★☆
You will need:
- Foam for base
- Flexi-paint or Hexflex (lots of layers of pva glue could also work)
- Silicone
- Cardboard
- Clear tape
- Resin
- Disposable cups
- Sticks for stirring, lolly pop sticks work well
- Dyes in your preferred colours, here I used orange and red
- Sanding paper minimum
- Mouse sander &/or dremel maximum
- Clear nail varnish or Clear coat spray
- Paints
- Super glue
- PVA board (can also use foam)
- Worbla
- Hotglue
- Heat gun or lighter
Exhausted yet? DW a lot can be swapped out.
◦•●◉✿ ᔕᑭOᑎᔕOᖇ ✿◉●•◦
It's me. I'm the sponsor.
I make a spicy shark dating sim and soon a genshin impact one, check it out here:
dorian.app.lin...
◦•●◉✿ ᔕᑭOᑎᔕOᖇ ✿◉●•◦
How to text version:
1) Draw out the pattern for the blade shape you want, include the handle and the shape at the bottom of the handle. leave out the hilt for now.
2) Make it out of foam, cut out a few layers if thin, then stack them. Carve/sand to shape.
⭐️Keep in mind, whatever the foam piece looks like when going into the silicone, is what the resin will look like the other side. Get it to the shape you want first.
3) Once you are happy with your base, cover it in something that smooths it out. Like flexi-paint, hex-flex, pva glue etc.
⭐️ Now you have your base, let's move on to silicone
4) Cover a flat base in clear tape, can be cardboard still but you want something portable and sturdy.
5) Hot glue your base down to this.
6) Wrap card higher than you want the silicone to be in tape and build up a house around the shape of your base. Use hotglue to fill in all the gaps around the edge.
⚠️ Try to make sure there are no leaks. Seal every gap in hot glue
7) Mix your silicone according to the instructions and stir a lot
8) Pour slowly into the cardboard house, covering your base by at least an inch or two in height. more doesn't hurt incase of leaks
9) Check regularly to be sure there isnt any leaks. If there is, do you best to patch it up with ducttape or something. Your goal is to slow it enough that once it starts to set, it stops.
10) Once set, leave another 24 hours just to be safe then we can peal the cardboard off and the base.
11) Carefully cut around the top to tidy it up and cautiously remove your base foam prop. If you need to do slits go ahead.
🌟You now have a silicone mould!🌟
12) Time to mix up the resin according to the instructions.
⚠️Make sure you're in a well ventilated area with proper PPE⚠️
13) I made 2 cups, one orange, one red, pouring them slowly around the same time.
14) Run heat over the top to remove some air bubbles
15) Let set. Leave for a day or 2 longer than being solid as it will still be flexible for a while
16) Carefully remove the resin blade.
🌟You got the resin base!
17) Now it's time to sand it! This is what gives it a gorgeous finish
18) Keep in mind not to make it too sharp, especially if you want it as a con prop- make it blunt af if you do
19) Once sanded, wet sand, working your way up to the highest grit you have.
20) Clear coat spray it or clear nail varnish it, along those lines. This fixes the "fogginess"
21) Use pva board or foam to make the hilt and use worbla to fill in gaps or foam clay or just more foam. loads of ways to do this. Heat helps shape it around your blade.
22) Put masking tape or paper over the blade and draw out the pattern you want on the blade and cut this out of thin pvc board or foam, paint black and super glue on OR pain directly onto the blade
23) paint the hilt and pummel
24) Wrap preferred fabric around the handle
25) Tada!!
🌟⭐️🌟⭐️🌟⭐️🌟⭐️🌟
This was a hard video to put together as so much footage was broken. But i didnt want to not put anything out.
Негізгі бет Solo Leveling: How I Upgraded the Knight Killer Dagger - Tutorial
Пікірлер: 5