can you do a video on start to finish on connecting a 4 channel amp. thanks
@brandonblount8184
8 жыл бұрын
The string inside is used to cut the outer jacket so that you can pull the inside wires out. Think of it like wire loom, the string can create a split in the outer jacket and then you can slide the wires out and cut away the jacket
@Trapperjohn1000
8 жыл бұрын
This channel is easily in top 5 of you tube car audio.
@CarAudioFabrication
8 жыл бұрын
Appreciate the kind words, thank you!
@elbertlee5485
8 жыл бұрын
Trappe
@erikramirez2572
7 жыл бұрын
CarAudioFabrication i have a question i bought a new single din stereo for my project but its not sending a equal sound to the mids and subwoofers so im getting more bass than voice what could be the problem ad what can i get to fix it thanks in advance !!!
@seanmichael2777
3 жыл бұрын
@@erikramirez2572 what amp are you using ? Is it a 4 ch , 5 ch ? Or does your radio have 2 pre-outs and are you using a Y-adapter for the RCA’s ?
@GirthBrooks775
6 жыл бұрын
Love the channel! Two people got close to what the string is for. If you want to see an example, watch someone terminate cat5 cable. Use a blade to strip the outter jacket, then with the string, split more outter jacket, then cut off everything past where you stripped with the blade. This makes extra sure that you didn't knick any of the inside wires and get ingress or egress.
@superronron
8 жыл бұрын
I use speedwire. It is awesome for like you said signal from a factory source to a processor. I have also used it for bypassing factory amps when replacing the headunit. I have been doing the heat shrink on the end and it is the icing on the cake. Great video!!
@xaytana
8 жыл бұрын
Just for normal speakers, and depending on the length of the run, you could probably just cut the outer insulation and use each pair for the speakers. Saves on costs of buying extra speaker wire when you already have a spool of it, and keeps the install color coded if you're doing a complete install down to the individual wires. Also if you need a larger gauge, for whatever reason, use two sets, which if this is 18 gauge, that'd be about 15 gauge, which is just barely enough if you were powering a speaker at 474w@4ohm at 20 feet with a db loss of .27, 18 is barely enough for 118w@4ohm at 20 feet with a db loss of .53, going by the 300 kcmil per amp, assuming the calculations are based on copper. Both have a power loss, 18awg is ~4w and 15awg is ~29w, due to resistances in the wire, although it would be slightly higher due to other resistances in the circuit.
@MrSpanky473
8 жыл бұрын
I have it running from my mid/high amp, back to my factory harness...works just fine.
@Stevejihad
8 жыл бұрын
Lots of uses of "9 wire" aka speedwire. I've used it to relocate a hvac control panel as well as many times in 4ch and processor installations. Very handy stuff!
@CarAudioFabrication
8 жыл бұрын
Another great use. Thanks for posting
@doitrightthefirsttime8952
Жыл бұрын
Is this stinger wire big enough to handle a Rockford fosgate t600-4??
@bryancoxttu
8 жыл бұрын
I did a build in a 2013 F150 with Sony "premium" sound. I used 9 wire to tap the signal from the factory amp under the center console and route it to the back wall to my DSP. This product is very very useful. Especially in an age where in the premium vehicles we are dealing with factory processors that do much more than just amplify sound.
@davidgorby814
8 жыл бұрын
Love speed wire, been using it since 2008.
@CarAudioFabrication
8 жыл бұрын
Good man. :)
@kendrickray7827
8 жыл бұрын
mark can you do a video on wiring head units to preamp to amplifiers.... I would like to visually see where each rca cable need to go installing
@gregchamberlin5954
3 жыл бұрын
I wish I had known about this product when I installed my power fold power telescoping mirrors on my excursion! I twisted my wires into a nice loom, but this would have been a lot easier
@alphaboltz
8 жыл бұрын
there is 4,5,6 and 7 conductor wire, it's used in trailers so if you don't need 9 wires you can use that and it's inexpensive.
@ajbrown2013
4 жыл бұрын
Hey mark I got a mini van I use for work it’s kind of a Frankenstein Mobil at this point! So far I have done all new mechanical stuff under the hood suspension all of it axels u name it! Took the dash out seats all the plastic crap not putting it back in making fiberglass everything. I have a 5 channel amp and a mono amp I have 3 sets of 6x9 and a set of supper tweeters and a set of 12”s I have removed all factory switches and made my own windows mirrors hvac buttons installed a 10” WiFi radio 2 12.9” I pads and one 10” I pad... I have installed 2 50” light bars and four led spot lights. I have a huge winch I need to put on emergency flashers. Thanks to all these videos you make and others for giving us the pro tips of installing all this stuff
@Troy_Audi0
8 жыл бұрын
I do think they have a 5 conductor as well if you do not need the 9, I use it for Signal or harness extensions, Also nice for basic Xover install you can use the Signal in to correspond with the correct location (L/F = Wht/ R/F = Gry) I use 16/2 or 16/4 Home wire for my speakers runs. Great Video Marc! Thumb is Smashed!
@timd1897
8 жыл бұрын
ive been looking for this type of wire of the longest time! never knew the name
@208miuwu
8 жыл бұрын
The shop I had move my AC controls in my Tahoe to a custom built console back in 2010. That stuff is amazing and professional looking too.
@pariahzero
8 жыл бұрын
I'd suggest an ideal cat-5 insulation knife. You can adjust it so it cuts almost all of the insulation, but doesn't nick the signal wires. It's much more repeatable (and idiot proof) than trying to do it with a set of cable cutters or knife.
@CarAudioFabrication
8 жыл бұрын
I'll have to check that out.
@DJMoPhiya
7 жыл бұрын
They are also great for factory amplifier bypass fixes.
@PANTYEATR1
8 жыл бұрын
are there any RF noise issues with having 9 wires so close together???
@letsgoracing78
2 жыл бұрын
So I'm planning on going from the cars stock wire harness down to the 4ch amps under my seats. I do have a aftermarket harness plug so obviously it wouldn't be hardwired in. And I'll just cap all the speaker wires coming off the new deck going in the car.
@shawng7902
6 жыл бұрын
Found it funny you liked the sound of unwrapping that plastic, for me it's the sound of pulling wire especially speaker wire. Don't know why. I always loved the sound it makes when it hits something. I think it's the fresh new install feeling.
@danielradasanu928
3 жыл бұрын
I don't understand one thing , the one with 9 cables ( 8 for 4 speakers ) and the blue for remote has to be connected on remote on the aftermarket player? or all the wires connected to the harness???
@BigSunday512
6 жыл бұрын
I used to use this type of wire back in my lowrider days! Used to connect the switch box to your hydraulic pumps. :)
@sjared309
8 жыл бұрын
we're can I get some speed wire from for good deal
@korg47237
8 жыл бұрын
Another big use is a factory amp bypass where it had a digital input from the factory radio.
@CarAudioFabrication
8 жыл бұрын
Very true
@mytubesteakout
Жыл бұрын
If you're running a power wire next to speaker wire, such as the blue turn on next to the speaker wires, wouldn't that potentially introduce noise?
@EvenTheDogAgrees
7 жыл бұрын
Ooh, nine-tailed whips on roll, cutable to size. This shall go far in certain scenes... ;)
@junjunlecaroz5393
4 ай бұрын
Hi Mark, just a quick question for you, can i used this speed wire for dsp amp output? 2 way active front? thanks.
@ilovetoyotatrucks
8 жыл бұрын
it is the same awg as your factory speaker wire it's absolutely great to use when adding a 4ch & replacement coaxl's (I ran jBL off of scoeshe Brand OFC 9 wire & it sounded great) however as I went to components I upgraded entirely all the way from amp to speaker 12awg fosgate & my 2nd set I was comparing & used monster cable 12awg however I'm liking the fosgate as its cleaner & easier to run the Monster Cable 12awg is not made anymore & it's too thick under the carpet ect tucking was a pain, easier with fosgate although both are PC-OFC
@DapimpBDSD
6 жыл бұрын
this wire reminds me of prepping cat5/6 jumpers/lines
@jeremiahbright706
8 жыл бұрын
Canare star quad is good for 4 conductor runs too(or making RCA cables)
@lctachell
8 жыл бұрын
Great video. Learning alot. Also just want to give you a heads up, when you were filming close up to product/hands, the white counter top is white washing out the video. Might have to adjust your white balance of camera or dont use the counter top
@majik895
Жыл бұрын
What would you use instead of speed wire to hook up the speaker wire to your 4-channel amp? My installer used it to send a signal from the head unit to the Focal AP-4340 which I believe is 75W per channel. I have noticed that the amp should be producing much more sound than it is. Thanks for reading!
@v8soarer1991
7 жыл бұрын
Geat videos. Do an awesome job of explaining different areas of car audio industry. Reminds me of 7 and 5 core trailer wiring
@jessiegonzalez8571
8 жыл бұрын
Its great for installing hydraulic suspension systems.....
@MobWithGuns
8 жыл бұрын
So in essence it's just a roll of recolor-coded cat5 cable ?
@CarAudioFabrication
8 жыл бұрын
CAT5 is usually 24 awg which is very small.
@jmcguire708
8 жыл бұрын
much much thicker, cat5 carries signals, wouldn't work for amplified sound.
@jlane7731
Жыл бұрын
I’m at HVAC technician. Is there anyway I can use regular 18 gauge thermostat wire to power my speakers or at least get a signal to my sub?
@bradpitt1263
2 жыл бұрын
Do I connect the speed wire to the radio or to the harness or both
@carlitot5388
4 жыл бұрын
Is the sound gonna be different with the speed wire ! Or go with thicker gauge! I’ve a Rockford fosgate punch amplifier 4 channel! 400 watts! Alpine 5/12 and alpine 6x9s! Pioneer super tweeters! I would like to use the speed wire!
@paulpopp1999
3 жыл бұрын
You think this 9wire would be ok to connect to a JL300/4 slash series amp run up to my head unit to power my 6x9s?
@1HotLegendLS
6 жыл бұрын
For only 4 conductor I use 4-flat trailer light wire.
@cott1494
3 жыл бұрын
Hey, I just got the SONY XAV-AX7000 with the high output. would it be necessary to rewire my speakers?
@Forevermct1
8 жыл бұрын
Already use it and it is great!
@Sleepy731
4 жыл бұрын
Would this be ok to run from sub to factory door speaker wire omg behind stereo? Running 4 infinity reference 6x9s. Thanks in advance
@qcfire65
5 жыл бұрын
What wattage can the speed wire be used for? I’m going to have Audiobahn 50x4 on a set of Audiobahn 6.5 components.
@nightmaremunoz8384
8 жыл бұрын
ive been watching since you only had a few videos and i learned how to build the boxs from you too i was wondering if youll do a video on speaker wire gauges and there different benefits. i have a single jl w6 v3 but i got it before i started building boxes the guy used what i think is 16 awg twisted together for some reason? on my other boxes i built i use either 14 or 12 gauge does it matter at all?
@chatobalencian1504
4 жыл бұрын
Hey brother I been following all your videos I'm going to be doing a big install and can't decide to use speed cable to run from behind deck to my 1200.6 phoenix gold amp or should I run some stinger 12 gauge
@irepbigi
8 жыл бұрын
I use it for hydraulics & bags
@bestmoll3714
8 жыл бұрын
thanks for all your insight....much appreciated
@aaronvizcaino9207
7 жыл бұрын
hey Mark if I'm using 12 feet long 9 conducted wire how many watts would be the most the i should used for? because I got 600w 4 channel kenwood excelon amp or u recommend just 2 us speaker wire
@GnosisMan50
4 жыл бұрын
I just bought some of this stuff...crap! It's 1/2" in diameter. I need to install about 16 feet of it. I also need to layout my 4 gauge power cable which is about 3/8" diameter. Why can't they make these wires flat? It would really help getting it underneath the carpet so that it doesn't bulge.
@koakahipedro8662
4 жыл бұрын
Just tuck it under the trim?
@HumbolSkitso
8 жыл бұрын
What do you mean grab the signal for a dsp? You're going to use that in place of RCA cables?
@CarAudioFabrication
8 жыл бұрын
Tap into stock head unit speaker wires for signal. Factory radio on this vehicle.
@Moneys169
4 жыл бұрын
Mark. What are your thoughts on this wire now with say the JL audio vx800
@karanvirsupple772
5 жыл бұрын
Do you think the blue wire on this if used as amp turn remote turn on can create interference with speakers?
@CarAudioFabrication
5 жыл бұрын
No
@Filthy_PhilDance
7 жыл бұрын
Would this be good to run rocker switches with?
@kobezcarz4558
4 жыл бұрын
I have my trunk done. Amp rack.. I've ran speed wire to my dash... I dont have much room to solder. . Does anyone know where to order proper harnesses for this purpose? ? If not I'll struggle wiring to the factory harness.. please help. Get channel mark.
@kobezcarz4558
4 жыл бұрын
Also. This speedwire is from my dsp
@riadlassel1696
4 жыл бұрын
good job bro you're really amazing good luck I'm a fan.
@johnnyarroyo5697
4 жыл бұрын
Purchased speed wire for an install using it on a 4 channel amp only running from harness behind the radio to amp instead of running wires all over the car is it safe?
@johnnyarroyo5697
4 жыл бұрын
Thanks in advance
@Bhpyatte
5 жыл бұрын
Would you recommend using the speed wire for tweeters that run 80 watts rms?
@paulcampbell8696
4 жыл бұрын
Definitely.
@Quanie156
7 жыл бұрын
thanks alot
@j249007
7 жыл бұрын
I was recommended this wire to rewire my amp to the aftermarket 6.5 audiopipes to cut signal interference. Would this carry enough power to the speakers? 250w each
@Habib.544
4 жыл бұрын
Can use ethernet cable instead of this cable ?
@alex-ur3vp
2 жыл бұрын
yup
@vgullotta
8 жыл бұрын
MOAR Jeep build plox!!! =D
@meanpaintandbody
7 жыл бұрын
How much amps can it handle per wire?
@SrgBlackburn
7 жыл бұрын
8 gauge should hold about 10amps MAX!
@DEXMER1
7 жыл бұрын
Can I use speedwire for a 4 channel amp hifonics running kappa infinity speakers?
@firebirdude2
7 жыл бұрын
Of course man.
@Colopathe
7 жыл бұрын
Daniel Mendoza Depends on the amps/power of your amp
@orlandoc5219
8 жыл бұрын
hey Mark, i really need help on this... can you do a video on installing an aftermarket system into new modern vehicle with an integrated screen head unit with controls on a steering wheel. what i want to do is to install two after market amps one for the mids and high and one for the sub. the vehicle is the mercedes benz cla 2017 with the harman kardan factory upgrade.
@thedivinehammerswoodworks1895
8 жыл бұрын
that system is all fiber optic, from the head unit to the amplifiers, changing out that stuff without messing up the rest of the car other integrated systems is best left to professional installers.
@orlandoc5219
8 жыл бұрын
is it possible to do though?
@orlandoc5219
8 жыл бұрын
were did you get the information on the that? of the fiber optic?
@thedivinehammerswoodworks1895
8 жыл бұрын
+Orlando c I am a mechanic, I work on Mercedes all the time.
@shelbyhoneysuckle1080
8 жыл бұрын
Two ways to do this. Grab the already amplified signal output at the factory amps, or gut the entire system and use a different source for audio and rewire the entire audio system. In my professional opinion, I wouldn't touch it.
@Quanie156
7 жыл бұрын
can this wire be used for speakON connectors?
@DJMoPhiya
7 жыл бұрын
Yes depending on how much power you are planning to use for that cable. Speakon cables tend to have a higher gauge wire than those in the quick wire. If this is for a pro-audio (stage and event sound) there are equivalent solutions just for that when you can buy it by the foot.
@Quanie156
7 жыл бұрын
Juan Romero, Jr. I want to use it for car audio. 4ch amp like 600watts rms
@DJMoPhiya
7 жыл бұрын
I would not recommend using speed wire as speaker wire. It would be more work to splice and split the loom in order to run pairs to each door, pillar or deck each speaker is located. I would recommend typical paired speaker wire. Reason two you are looking at approx. 150w per channel over an unknown distance. The gauge may be too small in this case as explained by CAF.
@TASTYTREATSPLS
8 жыл бұрын
Woo!
@LetThatBassDr0p
8 жыл бұрын
Try sitting in a 165db and then a 166db van and tell me you can't distinguish a 1db loss/gain. Lol. If you did want to try that out, come to Slamology next year! That's where I heard those, and tons of others!
@CarAudioFabrication
8 жыл бұрын
Feeling is different than hearing. You would never use this to wire subwoofers anyhow.
@LetThatBassDr0p
8 жыл бұрын
Oh most definitely. I was just givin' ya shit! lol.
@Fox9582
7 жыл бұрын
I didn't noticed till now... You're actually recording those videos in the kitchen hahaha... Your wife truly loves you 😅😂
@froshouseable
8 жыл бұрын
should have 10. reference ground.
@MiahDougie1
8 жыл бұрын
CAT 9
@youdig839
8 жыл бұрын
9 wire, awesome for gm.. my caddy has the harness n the trunk, dumb shit
@RdwalmR
6 жыл бұрын
so its just a cable
@n-e-u-t-r-a-l_-2039
7 жыл бұрын
I hate when people say you can't hear the difference.. Yes you really can,
@GnosisMan50
4 жыл бұрын
it's too freaking thick!! It was a nightmare getting this cable underneath the carpet in my car without bulging and without trimming my car trim to compensate. Don't they make this stuff FLAT!?
@CarAudioFabrication
4 жыл бұрын
Flat would be more of a pain, flat ia great for home audio where runs are simple, but good luck in car audio with all the bends the qire needs to take, you can't articulate flat wire for car audio applications
@AlienRiff
5 жыл бұрын
Can you use speedwire to make an interconnect set of rca’s from the headunit to the amps? I ran it to a line high end line level converter but I want to do away the converter and do away with the factory head unit but don’t wanna re run new rca’s.
Пікірлер: 112