Do you know if there is a way to connect an ELRS module too? I guess Spektrum would have to make a firmware update? I don't find any info about this
@bangdfpv3270
Жыл бұрын
I am pretty sure it will not support E LRS. The reason is, you need to setup the protocol to Crossfire protocol to communicate with the transmitter(Tracer). But i haven't seen ELRS model in the setting. Check out for any updates.
@RubyS.1
Жыл бұрын
I'll try it and let you know. Supposedly it works if your transmitter speaks crsf.
@jean-micheldupont1150
Жыл бұрын
@@RubyS.1 Thanks, I'm very interested in your findings.
@RubyS.1
Жыл бұрын
@@jean-micheldupont1150 elrs is a no go. But since spektrum is using the crsf protocol and not ppm or pwm the TBS nano worked just fine didn't have to configure anything just worked. Few people on discord said that elrs was working on thier spektrum with the newest spektrum update which supports crsf V2 but I couldn't find anything.
@jean-micheldupont1150
Жыл бұрын
@@RubyS.1 Thanks! I think I will buy a crossfire module then.
@MG-ki3vm
3 жыл бұрын
Id like to do this. Can you tell me how you got on with range and also programming the Tracer. Do you activate it in the menu the same way you would the full size Crossfire? Thanks for the vid.
@bangdfpv3270
3 жыл бұрын
Thanks MG! For the progamming goes the same with Crossfire. Inhibit "Spektrum RF" and activate "Crossfire V2" (it should be V2 if you have the latest firmware of your DX9) I flew my quad yesterday, but one thing for sure, it definitely out range my omnis, inwhich my previous SPM4651t wasn't capable of... so now VAS crosshire extreme on its way. I will make a separate video as soon as I receive it!
@bangdfpv3270
3 жыл бұрын
@Nathan Castets Hello! My version is 2.01 by the way. For the crossfire protocol I didn't touch anything, only requested for version updated to the distributor here in Korea.
@amauulau3574
3 жыл бұрын
@@bangdfpv3270 please share for v2..just install module but no function every channel after success binding n updating module n rx..tq
@bangdfpv3270
3 жыл бұрын
@@amauulau3574 did you set the betaflight configuration protocol to Serial(SPEKSAT, SBUS, SUMD) & CRSF(Crossfire)? I tried CRSF V1 in my DX9 but seemed to work
@amauulau3574
3 жыл бұрын
@@bangdfpv3270 i convert nano rx to pwm,,for plane..
@jmlon993
2 жыл бұрын
you cant run any lua scripts though, so no tx settings changes or smart audio
@bangdfpv3270
2 жыл бұрын
Your right. DX9 not capable for open TX. So I configure vtx smartaudio settings via OSD.
@RemcosFPV
3 жыл бұрын
Will this work with dx6?
@bangdfpv3270
3 жыл бұрын
Unfortunately, I find it low possiblity with TBS Tracer due to below reasons. 1. DX9 was built more opened for future enhancing from the first. The soldering pad "J16" was made for those reasons.. but not sure for DX6 2. To use it this way you need to change the protocol setting to "Crossfire" in the DX9 setting but I am not sure if DX6 is capable of that function.
@RemcosFPV
3 жыл бұрын
@@bangdfpv3270 I may open up my dx6 and see if it has that pad for it
@bangdfpv3270
3 жыл бұрын
@@RemcosFPV great and also check if you can change the protocol as well to "Crossfire". Refer to below video from 06:30 kzitem.info/news/bejne/tot9yHiLgIt1oKA
Пікірлер: 20