Great informative video Phill, just a quick question I have the gxff you obviously prefer the tri tec tips to the graco ones just wondering if they are better or if it’s a personal preference cheers
@ProfessionalPainterDecorator
3 жыл бұрын
No .. I do have a a couple of Graco green FF tips... And use them ... But I've found I've bought more Tritech tips and keep with those. The GXff came with a loft 210 tip, which I've used too. You may find you'd not really notice much different when spraying.
@rogerbell123
3 жыл бұрын
@@ProfessionalPainterDecorator thanks for that I tend to use the 210 tip which came with mine and been happy enough with it was just curious in case there was a better system thanks for the reply keep up the great work
@ProfessionalPainterDecorator
3 жыл бұрын
@@rogerbell123 big thing for me is tips wearing and also blocking up.. then having something to fall back on if I'm on a spray job.. you need a spare back up. ;) the 208 gold I used as a final coat gives a very nice 'mist' spray... but .06 and .08 do seem to block a bit more with the waterbased paints.. as really they are geared for thin stains and lacquers etc. But thin the paint enough you can get away with it ;)
@thomasjoyce9348
5 ай бұрын
do you have any videos on taping up then spraying the walls after the woodwork? (obviously with brush and roller its walls then woodwork) i do new builds/domestic would be interested at trying a new approach with my new graco ff
@ProfessionalPainterDecorator
5 ай бұрын
There's taping up videos from early on on the channel. But I'd be rolling the rolls not spraying. Unless the ceiling and walls were the same colour
@grislyflatlander9405
Жыл бұрын
My compliments to the most thorough, generous,genuine and spot on painting how to videos.Keep up the good work!
@ProfessionalPainterDecorator
Жыл бұрын
That's very kind of you to say. Please share and share and share... Spread the word :)
@stevecoppell8871
3 жыл бұрын
Your a good teacher. Thanks for the effort!!!
@ProfessionalPainterDecorator
3 жыл бұрын
Thank you 😊
@bettycaldwell9570
3 жыл бұрын
we should be careful the way we spend money, if you are not spending to get profits at the end, your gradually moving into poverty.
@ProfessionalPainterDecorator
3 жыл бұрын
We can all work for nothing 😉
@paulcampbell6316
4 ай бұрын
Fishnet stockings work best! 🙄
@ProfessionalPainterDecorator
4 ай бұрын
Yes they do... But I very rarely wear them these days.
@markmccarthy456
2 жыл бұрын
100 mesh
@paweljaniak8621
Жыл бұрын
Phil you are a true Gent! I just clicked subscribe after watching 2 of your videos and I am excited to watch more of them in the near future. I am a joiner/ cabinetmaker and have recently purchased the GXFF to spray my products and even my newly build house so your information to me is priceless right now. All the very best and keep up the great work brother 😉💪🏻 Pav
@ProfessionalPainterDecorator
Жыл бұрын
At last you found me, what kept you lol Glad it's helped. There's a few vids on setting up the gxff and cleaning out.. which is easy done with one decent bucket of water. The next vid you need to watch is the spray top sizes if you don't already know. The gxff is very versatile... As you see, I've used it on ceilings and walls.. Woodwork.. paneling and furniture.
@ajsbrushworksllc8348
Жыл бұрын
I'm in the US, grew up in the northeast, we called it woodwork, I live in Texas now and still call it that, man, people have no idea what that is. Lol.
@ProfessionalPainterDecorator
Жыл бұрын
Hi. Thanks for getting in touch. What took you to the US?
@ajsbrushworksllc8348
Жыл бұрын
@@ProfessionalPainterDecorator lol. I am American. Born and raised in the northeast.
@RobbieRegan-f7l
Жыл бұрын
Im that viewer your clearly addressing this information to. I run a painting business here in N.Ireland, its going very well thank god. Im sitting here deciding if and how will i jump into the spraying end of the business. I have 6 staff along with myself and im ready to invest. Phil Your videos and you as an advisor are very easy on the ear and understanding. Would you have an email or contact number i could contact you asking some further information? cheers fella... Keep up the good work
@ProfessionalPainterDecorator
Жыл бұрын
Thanks for sharing! Have you FB or Instagram? Most can DM me via those platforms. Speak soon
@Trickyhat1
Жыл бұрын
Nice to see David Brent has fallen on his feet
@eezy251able
2 жыл бұрын
These are great thanks! If you wasn't using the same colour on the walls I'm very intrigued on how you would finish the walls? As in would you spray them or Roller them?..
@ProfessionalPainterDecorator
2 жыл бұрын
Cut in and roll walls, is pretty easy to do. Also future touch ups can be done.
@eezy251able
2 жыл бұрын
@@ProfessionalPainterDecorator yeah I thought so. Wasn't sure whether you just sprayed the whole lot?
@ProfessionalPainterDecorator
2 жыл бұрын
@@eezy251able if all the same colour, you can do.
@benwilkinson5457
10 ай бұрын
Hi mate, how come you only use a 110 tip. This only gives you a 2" fan? Do you find a wider fan puts on too much paint creating runs?
@ProfessionalPainterDecorator
10 ай бұрын
a 110 does put a lot of paint on in one 'area' i uses 210 and 310, 308 etc as well. its good to have a few different tips to hand
@fiazkhalid3542
Жыл бұрын
Hey Phil, great informative video. What colour paint is that please and is that for the walls or woodwork
@ProfessionalPainterDecorator
Жыл бұрын
Hi. F&B Charlton Grey, from memory. Helmi 30 for woodwork... Optiva5 on ceilings and walls.
@richardloze5994
3 жыл бұрын
watched the vid again. so just ordered my hopper kit from sprayman with 310. 210 ,110 tip. they supply 100 mash is this the right one for the 110 tip. not sure if you said.
@ProfessionalPainterDecorator
3 жыл бұрын
On my Tritech gun. It's the red filter. Which I think is the fine one for .10 tips.
@carolinebridges8968
2 жыл бұрын
Could I spray an oak sideboard with Toms kit Phil?
@ProfessionalPainterDecorator
2 жыл бұрын
yes you can. :)
@christopherdonnelly4218
3 жыл бұрын
Hi Phil, I am just getting into spraying and have started a job 12 doors previously painted with gloss I have sanded them washed them down can I use dulux trade wood primer u/c on them first before I use everal aqua 40 ? I would appreciate your help or advice 👍
@ProfessionalPainterDecorator
3 жыл бұрын
Hi. Personally i don't like mixing and matching Undercoat brands with top coat brands. Keep with the same when it comes to the UC and top coat. Over previously painted gloss I'd go a nice coat of otex akva, then finish two coats of Everal Aqua 40... For build up you can always give it an extra coat of UC, or an extra top coat if you feel the need I wouldn't do Dulux UC then a Tikkurilla product. Keep me posted
@richardloze5994
3 жыл бұрын
Great video again. I'm just about to buy the hopper kit for my gx21 to start spraying woodwork . Gonna practice in my garage. Please keep the vids coming.
@ProfessionalPainterDecorator
3 жыл бұрын
What shall I do next?
@richardloze5994
3 жыл бұрын
@@ProfessionalPainterDecorator I would like to see how you mask of the woodwork to do the walls. Also no bleed trough on the tape so you have super sharp lines. Also how to spray bannisters one day. Thanks.
@ProfessionalPainterDecorator
3 жыл бұрын
@@richardloze5994 Ive those on Instagram. Are you following us on there? I'm on Instagram as @beckwithdecorators. Install the app to follow my photos and videos. instagram.com/invites/contact/?i=1vagmkpjunkd9&
@PaulJacksonOttawa
Жыл бұрын
Ahh Phil These tips and what you share are priceless. I can't tell you how often I use the stuff you've taught me in your videos. What you say at 33:10 really important. Thank you Phil. Please keep em coming
@ProfessionalPainterDecorator
Жыл бұрын
Great to hear! Many thanks. Share Share and share ;)
@gerardmcparland8643
3 жыл бұрын
Another Fantastic informative video! From the Legend Phil Beckwith. Gonna dip my toe in the water and buy a tri-tech 190 just to get me started. Would you have any advice on my choice Phil?
@ProfessionalPainterDecorator
3 жыл бұрын
Three words. Budget budget budget.... What's your budget. The 190 will start you off and will be a good little machine... Think what you want to be doing with it... And will you start wanting to use it more and more? You will!!
@hakimvlogs6579
5 ай бұрын
I can’t open my filter thing for my erbauer sprayer Can you show me how
@ProfessionalPainterDecorator
5 ай бұрын
In the gun? You may need a spanner on it if it's tight
@peterhalstead7281
5 ай бұрын
Just get on with it
@t-rocket6381
7 ай бұрын
I like the sponge tip…..thanks
@ProfessionalPainterDecorator
7 ай бұрын
You’re welcome 😊
@cristi95vcl
2 жыл бұрын
Hey Phil , what sprayer/type do you recommend for wood-work use ? Thanks
@ProfessionalPainterDecorator
2 жыл бұрын
Hi. I use both my HVLP and airless. Both have their own advantages. Hvlp can spray smaller amounts, more control. Airless.. with a hopper kit.. can spray your woodwork/trim paints with ease. Use the smaller FF tips like I talk about. I've the QT5 hvlp with a remote pot. Also a Graco GXff and a Graco 495st Max II. It's down to budget and how often you'd be using it.
@ibanezrg470
2 жыл бұрын
Painting large and small areas for years and the amount of times i thought to myself this would be so much easier with a sprayer.
@ProfessionalPainterDecorator
2 жыл бұрын
it has it's time and place. ;)
@Onionpeto
Жыл бұрын
I like what you say about raising the perception of painting & decorating, keep it up !
@ProfessionalPainterDecorator
Жыл бұрын
Thank you! Will do!
@barrybostock3737
4 ай бұрын
Hi Phil, got me hooked on the spraying idea! Suggestion on a intemediate setup, woodwork initially then moving to ceilings and walls? Graco? Wagner? I even watched the erbauer video? Any help on this front would be great. Wanting to up my game locally and not be frightened of spraying if i purchase the wrong kit. Work smarter.......Thanks for all your videoes help and advice. Top man phil. 👍
@ProfessionalPainterDecorator
4 ай бұрын
Good stuff! Watch more of my airless spray videos on the GXff and my other set up. It comes also on what you'll want to spend. Don't go cheap
@barrybostock3737
4 ай бұрын
All noted, video watching Phill. Keep you posted. Many thanks for your time. 👍
@Cillianofarrell
3 жыл бұрын
Great info as always. Really appreciate it. Can I ask, with the emulsions on the walls and ceilings do you spray and back roll or just put the final coat on with brush and roller?
@ProfessionalPainterDecorator
3 жыл бұрын
this room isn't very big, so I've cut in a rolled the ceiling and walls. Other rooms have been sprayed ceilings (tikurilla ar2) and walls cut in and rolled (tikurilla optiva5). My previous video tells you my process on rolling a wall... I also speak about the process used for the job. Hope that helps.
@Cillianofarrell
3 жыл бұрын
@@ProfessionalPainterDecorator thanks for replying Phil, I'll check that video out after work. When I was in Australia for a year painting new builds we would spray walls, ceilings and WW with one coat of the same primer(sealer as the aussies called it) and no back rolling then finish everything with the brush and roller. Do you use a similar system yourself? If that's covered in your other vid then disregard this question. Have to say these vids are the most comprehensive on KZitem, really great info fella.
@ProfessionalPainterDecorator
3 жыл бұрын
@@Cillianofarrell thanks for the kind words. I'm trying to show people how I do it as a normal painter and decorator... No fancy filming... No fancy scripted words... It's as it is. Only basic editing the final cut... How you see it is me doing it.... Like others would be. On new build. The wash coated are sprayed.. then ceilings finished by spray.. woodwork too. Walls cut in and rolled... Just incase touch up is needed. If ceilings need touch up.. it's done with a small short pile roller... Carefully ;)
@Cillianofarrell
3 жыл бұрын
@@ProfessionalPainterDecorator cheers for all that Phil. Keep up the good work pal
@JONO3679
3 жыл бұрын
@@Cillianofarrell usually we tint all sealers to the top coat colour.. and roll on the last coat because you can't touch up spray...in the uk the houses are alot smaller so you could spray finish if you wanted
@staffh3815
2 жыл бұрын
Phil just a tip dont use crotchless tights,I ended up with loads of bits
@ProfessionalPainterDecorator
2 жыл бұрын
Noted. But those are the ones I keep to one side ;)
@bikagirly
Жыл бұрын
I've never been confident enough to get a sprayer .... but after this video I feel slightly better about it. After all I could just message you for more help! Xx
@ProfessionalPainterDecorator
Жыл бұрын
Glad I could help!
@ProfessionalPainterDecorator
Жыл бұрын
I'm over ta Oxton spraying ceilings and woodwork this week..... Occupied house ;)
@garethdavies7564
2 жыл бұрын
where did you get then spray tips cleaners from?
@ProfessionalPainterDecorator
2 жыл бұрын
Various spray supplies should sell them. Google spray tip needle cleaners
@davidsmalley8783
Жыл бұрын
Another tip for you Same tritech gun put some masking tape around the top of the filter as well as a spring Filter is tight into the gun Sprayed 22 doors and a staircase this morning Not one single tip block
@ProfessionalPainterDecorator
Жыл бұрын
What time did you use, what paint?
@davidsmalley8783
Жыл бұрын
Iam convinced bits go up the side of the filter Been using tape for a while Never let’s me down
@davidsmalley8783
Жыл бұрын
Acrylic primer Do you mean how long did it take ?
@mungojack
3 жыл бұрын
Thanks Phill. Got the sprayer out today for ceilings, HVLP is out tomorrow for the woodwork you have given me more confidence to spray
@ProfessionalPainterDecorator
3 жыл бұрын
Don't dismiss using the airless for woodwork... Correct tip size and pressure you be quicker than hvlp.... Less thinning of paint and you can get more paint on the surface when you need to build paint up ... Particularly on new woodwork... Like in this video. I still using my QT5 hvlp on woodwork too. It does have more control... But find more dust in the air due to the unit blowing air about ;)
@mungojack
3 жыл бұрын
@@ProfessionalPainterDecorator thanks Phill, have you done a guide to tip sizes and their uses?
@ProfessionalPainterDecorator
3 жыл бұрын
@@mungojack yes a few months ago, I've one that covers what the tip numbers mean..... have a look down my video list.
OMG sponge trick amazing. Could I use that method to do touch up say something gets caught when moving things around, rather than getting the sprayer out again? Amazing video
@ProfessionalPainterDecorator
Жыл бұрын
Yep... You mean you're not already lol
@marchandford7787
Жыл бұрын
Hi Phil, can I ask you something please. I used B.I.N primer on all my bare wood and sanded it with 120g painted in using Johnstones arctic satin. Left it over a week before masking it all to spray the walls, using a delicate masking tape. Anyway have to come to de mask and it’s all pulling of where the tape was. It has made a mess. Is there any ideas why it’s failed so badly? Any input on why and how you would go about sorting the mess would be greatly appreciated
@ProfessionalPainterDecorator
Жыл бұрын
@@marchandford7787 hi, what actually ulled off? it it pull off back to bare wood, or did the arctic satin pull off away from the BIN?
@marchandford7787
Жыл бұрын
@@ProfessionalPainterDecorator hay Phil the Acrylic Satin pulled off back to the BIN which I also sanded with 120g.
@nialloconnor5321
2 жыл бұрын
Thankyou so much for these tips really appreciate them , just found your channel really good mate 👍
@ProfessionalPainterDecorator
2 жыл бұрын
Awesome.... I'm here to help. Please, like share, comment and have a look through some of my other vids that may be of interest to you ;)
@nialloconnor5321
2 жыл бұрын
I will for sure pal Thankyou have a good weekend 👍
@colinwall2052
3 жыл бұрын
Great video,how long before you de tape,
@ProfessionalPainterDecorator
3 жыл бұрын
Depends. Sometimes same day later on, or next day. Or if longer cus of other work being done I run a blade around any tape edges that may be sealed/stuck with paint. No problems then.
@grahamstacey3149
11 ай бұрын
Legend, so helpful Phil 👍
@ProfessionalPainterDecorator
11 ай бұрын
Glad you enjoyed it
@seanbrown..brownsbuildings1424
2 жыл бұрын
Great videos for a beginner like me 👍🏻👍🏻👍🏻
@ProfessionalPainterDecorator
2 жыл бұрын
just trying to make it simple. if i miss out anything you need to know, just ask.
@seanbrown..brownsbuildings1424
2 жыл бұрын
The tips are very helpful, especially the sponge one . I’ll have to write them all down .
@bigjase6481
2 жыл бұрын
Little tip for your Phil, how about a fish tank heater in your hopper to heat your paint.
@ProfessionalPainterDecorator
2 жыл бұрын
now there's a thought, have you tried it?
@bigjase6481
2 жыл бұрын
@@ProfessionalPainterDecorator ill give a go, my gx 21 arrives tomorrow with the trim kit, been a professional sprayer in furniture, for over 12 years,pressure pot and and gun, so will be interested to see how different the airless is. But back to the fish tank heater, I reckon it will work a treat, maybe put a couple of Johnny's on it, in case it breaks.
@johnclogan7908
Жыл бұрын
u are the best ,,very good
@ProfessionalPainterDecorator
Жыл бұрын
In the words of Brian Clough.... Well, may not be the best, but at least in the top one LoL Tnx
@danielfitton437
2 жыл бұрын
Really informative video. i wonder if you have any suggestions for paint crazing over caulking. Caulking is fully dried and paintable but still get some crazing/cracking of the caulk. A coat of something like Zinnser BIN helps but not always. Any tips to help prevent the cracking?
@ProfessionalPainterDecorator
2 жыл бұрын
Change your caulk. I've had it previously. It's mainly when it's not a flexible caulk. I've moved over to waterbased caulk that can be used interior and exterior. I'm using RedDevil caulk and it's brilliant. Dries quick. Not had any crazing with it What is try is going over the problem caulk with a fine smear of more flexible stuff, allow to go off and see how it is. RedDevil caulk RRP is only about £2 a tube. Try it and let me know how you go on. On this vid I'd of used Fathog black tube interior/exterior flexible caulk.. but you can't get it anymore :( I think RedDevil is the same stuff in an other tube lol
@danielfitton437
2 жыл бұрын
@@ProfessionalPainterDecorator Thanks for the reply, I will pick up some RedDevil and let you know how it goes.
@ProfessionalPainterDecorator
2 жыл бұрын
@@danielfitton437 did you try some?
@danielfitton437
2 жыл бұрын
@@ProfessionalPainterDecorator Yes, it's way better than anything else i tried but when spraying the WRX satinwood I would still get a little bit in places. What's your go to satinwood when spraying?
@ProfessionalPainterDecorator
2 жыл бұрын
@@danielfitton437 I still like the Tikkurila Helmi 30 or Everal 40, they spray so well. Zinsser AllCoat Exterior satin also sprays well.. hvlp and airless.
@shayb9424
Жыл бұрын
Hi great vid Phill 👍 Just wanted your advice, can I use the gold 110 tip with the Wagner Control Pro 250M? Thanks.
@ProfessionalPainterDecorator
Жыл бұрын
As long as you use the correct spray guard for the tip being used.. shouldn't be any problems, swapping between different guns. I use a Tritech guard/tip on a Graco Gun.. and vice versa
@bigjase6481
2 жыл бұрын
Dorset paint, is like Dorset House prices. 😁
@ProfessionalPainterDecorator
2 жыл бұрын
it is a lovely part of the country though :)
@bigjase6481
2 жыл бұрын
@@ProfessionalPainterDecorator my home county, but living in Shropshire at the moment.
@ProfessionalPainterDecorator
2 жыл бұрын
@@bigjase6481 As good as Birmingham.... You'll be handy for anything going off at the NEC then. :)
@paulmaguire2592
3 жыл бұрын
Why do you not mask up on the walls around the frame? If you had to do a light colour on the walls it would take a few coats to over that up. What do you use for windows and to protect them mate?
@ProfessionalPainterDecorator
3 жыл бұрын
These walls are the same colour as the woodwork. Yes you can tape around if you wanted, just keep a fraction away from the top of the skirting edge so you have a bit of overspray on the wall that you will then cover when the wall is painted. Does that make sense? Windows I use plastic sheet drop on a roll with q1 tape and a 3m hand masker. I have another video on that showing masking walls up... Have you seen it?
@paulmaguire2592
3 жыл бұрын
@@ProfessionalPainterDecorator thanks for your reply mate, yes that does make sense thank you, I've ordered some Q1 tape and I find it does rip quite easy I not overly keen on it. I don't think I've seen the other video il try and find it later on this evening. Have a good one mate
@ProfessionalPainterDecorator
3 жыл бұрын
@@paulmaguire2592 which did you order? I use the yellow and orange colour the most, the purple is for delicate surfaces.. which is handy to have too.
@paulmaguire2592
3 жыл бұрын
@@ProfessionalPainterDecorator I've ordered the yellow ones. I've got prodec ones to try aswell I have been using the fossa ones from decorating direct and I find there good.
@ProfessionalPainterDecorator
3 жыл бұрын
@@paulmaguire2592 i use the yellow for general taping up, the orange i use when taping skirtings up after spraying as they are a little bit lower tack.
@nickyb6435
3 жыл бұрын
The Lidl's veg bag made me laugh, I've got exactly the same on my gxff. Great minds eh.
@ProfessionalPainterDecorator
3 жыл бұрын
Can't beat tights though.... You can't put a veggie bag over your head... And rob a bank LoL
@darylzeitner2966
Жыл бұрын
Thank you, just the tips I needed. Very informative!
@ProfessionalPainterDecorator
Жыл бұрын
Glad it was helpful!
@JONO3679
3 жыл бұрын
You need a bigger tip for you frames you should be able to do 22 frames in 30 mins then start again. Does that tip clogg up alot..
@ProfessionalPainterDecorator
3 жыл бұрын
I'd not got 22 frames to do lol
@JONO3679
3 жыл бұрын
@@ProfessionalPainterDecorator then its perfect 👌
@samrix5793
3 жыл бұрын
Awesome!!
@ProfessionalPainterDecorator
2 жыл бұрын
Thank you! Cheers!
@samrix5793
2 жыл бұрын
@@ProfessionalPainterDecorator hay! Was this just to check I was still alive?
@Garage_GymRat
3 жыл бұрын
Great video mate always enjoy watching them. I have a gx21ff that I'm fairly used to but I've just bought a qtech 5 stage with pressure pot, have you got any tips on setting it up mate?.
@ProfessionalPainterDecorator
3 жыл бұрын
Thank you. You'll love the qt5. Have you watched my other video on setting it up?
@Garage_GymRat
3 жыл бұрын
@@ProfessionalPainterDecorator ah no I haven't 🤦♂️ill go check it out now 👍
@cpercec
2 жыл бұрын
Great teacher!!
@ProfessionalPainterDecorator
2 жыл бұрын
Thanks ;)
@asdad2385
3 жыл бұрын
Perfectly said at the end mate 👍
@ProfessionalPainterDecorator
3 жыл бұрын
The but about having a few spray tips?
@asdad2385
3 жыл бұрын
Your comment about having a higher class of Decorator not just throwing Maggie on the wall 😂
Пікірлер: 140