Best video I've seen for mounting these. Only thing missing is when to remove the leveling accessory. If you don't remove it early on, it will get stuck the more they are tightened and have to start again.
@n1iex
2 жыл бұрын
The developer of this scope mount advises against removing the oil and using loctite ???
@jamescampbell4334
Жыл бұрын
I use SPUHR mounts exclusively. Buy once, cry once.
@Beltfedshooters
Жыл бұрын
I use to be a Scalarworks fan until I finally broke the dreaded hinge (heard it happens a lot) Wound up selling all my Scalarworks mounts and now run Spuhr mounts. These things are built like tanks.
@ocabj
3 жыл бұрын
The one thing I need to do is start using witness marks on scope ring screws. Every several months I'll just recheck the tightness with a limiter that is 5 in-lbs less that original torque to see if it's loose, but torque 'stacking' is always a concern.
@mapled3135
2 жыл бұрын
Love these mounts. I use the QD version on my K525 and my ZP5.
@flea-kh7om
3 жыл бұрын
Great job Frank! Thanks for the video. Take care, Vern
@pr0_tr0ll
3 жыл бұрын
If you read the instructions, it actually says not to you loctite on the screws.
@afkirby
3 жыл бұрын
“Ring screws are delivered waxed. Customers working in extreme conditions might want to degrease the screws and screw holes to loctite instead”
@afkirby
3 жыл бұрын
“All screws are waxed from the factory for proper torque values but customers working in extreme conditions may want to degrease the screws and screw holes and use Loctite 243 (Blue) instead. They may also want to use a small amount of gripping agent, such as powdered rosin, in the rings.” Here’s the more recent (2019) manual from the Spuhr website
@GBGuns
3 жыл бұрын
What about a false torque reading from "wet torque" with the Loctite? Is that an issue for scope mounts?
@michaelkennedy996
3 жыл бұрын
Love the hide. Thanks Frank.
@jeffguy3868
3 жыл бұрын
Great instructional video thanks
@hdveetwin
3 жыл бұрын
Make and model of scope. Thanks awesome vid.
@NightVisionViking
Жыл бұрын
Great video, thanks!
@tedbundy7167
5 ай бұрын
Cleaning the supplied screw from Spuhr and adding loctite is not the way to go. They have a thin layer of “glue” already added so they are ready to tighten to torque specs right out the box.
@Elfin4
3 жыл бұрын
Can you provide a link to that torq set you used please
@TheSpeza88
3 жыл бұрын
Fix it sticks
@sapper3619
2 жыл бұрын
What is the base that the mount it attached to for the install?
@huntersmith8924
2 жыл бұрын
You can get them on short action customs website
@duxrusso
2 жыл бұрын
Great video Zio! What hight are those rings if i may ask?? Thank you, best regards !! 🍻😷👍
@charleshetrick3152
2 жыл бұрын
When I use the leveling key it becomes impossible to remove after installing and tightening the screws of the rings. Does this indicate a problem with the scope or the mount?
@SHLowlight
2 жыл бұрын
too much pressure on the key, once you tighten the center, you can back the key out, you don't want to jam just hold it
@charleshetrick3152
2 жыл бұрын
@@SHLowlight yeah I guess I never realized how much compression really takes place, even at such small amounts of pressure.
@SHLowlight
2 жыл бұрын
@@charleshetrick3152 microns and milliseconds that is precision rifle
@charleshetrick3152
2 жыл бұрын
@@SHLowlight indeed so, I’ve in the past always used a method wherein I clamp and level the rifle then use a flash light and a plumb line. This time the rifle (an AR50) simply didn’t fit on my bench with the right clearances for the exercise. I’ve come to discover everything 50BMG requires another tear of accommodation. The most frustrating was the OCW test.
Пікірлер: 29