Y'all are the most patient couple I've ever seen... Ida taken that baler, dug a hole, put the baler in the hole and filled the hole with concrete... than I would have contacted a priest to perform last rights upon it.
@AutoCrete
2 жыл бұрын
Hanging a large glossy picture of the local scrap yard very near that square baler might provide some incentive to work better.
@sroberts605
2 жыл бұрын
lol
@josephpadula2283
3 ай бұрын
Concrete is too expensive, go with the photo !
@drdulas5055
2 жыл бұрын
Always make hay while the sun shines. Can always eat when it rains.
@boathead22000
2 жыл бұрын
you should have taken the round baler back in the field and bailed till it was done.
@bige.3474
2 жыл бұрын
Round baler should have been prepped and ready to go right after its last use.
@joekemp5034
2 жыл бұрын
That's why tractors have lights and sandwiches are quick dinners. Never stop just because you're tired and hungry. Always finish if rain is coming because now you just have stuff with all the nutrients washed out and probably mold.
@davidfeatch1436
2 жыл бұрын
Evan, you need to check and see how many strokes of hay it is taking your baler to drop a bale. If you are baling too slowly, this will cause banana bales because the feeder fork cannot get enough hay in front of it to push it all the way to the left side of the baler. I always liked to make a bale with around 16 to 18 strokes per bale on this model of baler. If your windrows are too thin to make this happen, unless you are going across the field in road gear, just rake more windrows together so you can travel around 2 mph to get the strokes per bale you need.
@davemcewen9991
2 жыл бұрын
Also you needed to make sure the feeder arm tines wernt bent and there were longer ones available to push the hay all the way across the bale chamber in light hay ,also make sure the restricter plates in the chamber, BACK BY THE BALE TENSIONERS arnt worn ,they can be doubled up as well , and check for weak or broken stop dog springs,that all contributes to banana bales.
@lawrenceb.3349
2 жыл бұрын
Despite your equipment problems, you take time to record it for us. Thank you so much.
@daleficklin1607
2 жыл бұрын
Don’t give up on that old square Baler. I have one like it and had problems but tinkered with it and with a very few new parts it bales great. May loosen the tension a little and check the hooks in the knotter for groves. Also, for reseeding check your local soil conservation district for a no till drill, some districts rent those for reseeding hay and pasture fields.
@beth4775
2 жыл бұрын
Sorry you two are having trouble with the baler. If anyone can solve the problem,it is you! Reason you are the best channel, you don't let setbacks,stop you, from going forward! And you teach,so well!
@jonathanwheat6275
2 жыл бұрын
Even though it got rained on a couple times. Flip the a few times to get it dried out. It will still make good cow hay
@jjarredondo6130
3 ай бұрын
the bale tie part is incredible. the engineering it took to get it right
@Me-ov9nw
2 жыл бұрын
Hard days work under your belt, still a win!
@teenagefarmer
2 жыл бұрын
Man that sucks Evan. Just keep at it, be positive and push on things will get better soon. At least you got plenty of hay for the year and were not in a drought this year. Great video, be careful, stay calm, don't worry and thanks for sharing.
@sledhead1017
2 жыл бұрын
Evan-you need to get some hay hooks.One in each hand will change your life when you learn to use them.Don't forget the lotion on the forearms tonight.you'll need it.
@jamesmoore1743
2 жыл бұрын
Evan I must stay I know you I truly happy of how Rebecca handled the tractor. Hats Off to you Rebecca if you read this
@harveystephens6115
2 жыл бұрын
Should have pull long day and finished baling. Farming, can’t put off tomorrow what you could have done today!
@CountryViewAcres
2 жыл бұрын
The dew starts forming at 8pm, at sunset. the hay would have been wet. Can't bale at night here. Too humid here.
@1dgrdgr
2 жыл бұрын
@@CountryViewAcres instead you've got wet hay and more rain coming. Maybe try next time and quit when the moisture meter tells you to. It's a bummer to see all your effort get rained on.
@ericheise4051
2 жыл бұрын
The only other option to save grass hay field is to use a wick wiper summer grasses weekly before it seeds out and pull seeds off .a ton of work .
@robertmotter4815
2 жыл бұрын
I bought 2 of your shirts and I think they have super powers in them because I get 2x as much work done on my little farm when I wear them! Your a hard worker!
@shirleybewley6646
2 жыл бұрын
Ah yes, weather and the life of a farmer!
@celestegeorge9101
2 жыл бұрын
My wife would follow me while square baling and check each bale and hand tie if needed. Yes, we fixed it but my wife walked quite a bit to get it baled.
@hastyhillfarm
2 жыл бұрын
I would consider round baling all of your hay, both cuttings next year. Keep how many rounds you need and sell all the rest and use the money to buy the square bales you need.
@johnbichell8023
2 жыл бұрын
You have the patience of a Saint and the mechanical skills of a pro.
@steverichardson2224
2 жыл бұрын
You are either very patient or you hide it well▪I was getting aggravated just watching when the baler would miss tying a bale! 3 things: 1) We made backstops for our wagons to have a good base to start with 2) Have you considered no tilling some Orchard Grass into that field 3) As bad as that hay is now; you still got to get it off the field to prevent future problems▪Farming stinks sometimes!
@CountryViewAcres
2 жыл бұрын
I have a backstop for the wagon I made. But once the bales are stacked, they lean against it and I can't remove the backstop. I need the back of the wagon to be open to unload in the barn. So I have to run without the backstop.
@denniscunningham7021
2 жыл бұрын
We had a Deere wire tie when I was a kid. Two men rode on it and tied the bales.
@bikerdad63
2 жыл бұрын
Evan glad you got a large portion of the hay in. Sorry you didn't get it all.me and my brothers would help the farmer down the street bring his hay and straw in every year. We unofficially adopted them as our grandparents.
@cedricgates9976
2 жыл бұрын
finaly someone that puts the bottom layer on its side!! saves on the twine being rotten and chewed we put the rest on its side man have i had days like that have to bite the bullet and bale at nite
@myharris
2 жыл бұрын
Neat trick with the wood block to swing the arm - major lightbulb moment for me, thank you!! My first year baling this year, with a Massey ferguson 10-8 baler, I *could* not figure how to get the dang arm to swing!! Thank you so much 😂😂🙏
@davemcewen9991
2 жыл бұрын
I LEARNED many years ago thats needed is grease under the baler toung were it slides and it moves easily .
@marcplocher6383
2 жыл бұрын
You can do it by backing up but it’s much easier with a block.
@TheIUBob
2 жыл бұрын
Ha ha, we always had a wire baler. No one ever wanted to work for us because the bales were much heavier than twine bales.
@davemcewen9991
2 жыл бұрын
WE HAD THE SAME MODEL a little older ,my grandfather bought it new ,it came with a wisconsin engine, the IHC H didnt have enough power to run pto and get up hills , battery start never worked ,you had to hand spin it, when dad took it over we switched it too twine tie ,and pto drive, we had a larger diesel david brown 990 then, and then i ran it until 1991,we baled 25000 small squares every year, so in its life with us that was 900,000 , no 1 likes it because the bales were to large and you could not get help to throw them that big, straight alfalfa was 80+ pounds and those balers no matter what tended to make banana bales or not tie on the left side, the only cures was 10000 twine and ram the hay too it , i was so glad when i switched to a 310 with a thrower and wagons ,you only needed 2 people then, i could bale all day and then mow when it was cool in the evening.
@nickmastroianni5557
2 жыл бұрын
You need a better plan Evan 'cause the weather (and machines) seldom co-operates. Suppose you square bale the number of bales your friend needs, stop and unload them in place and cover with a tarp. Then, continue square baling and drive the wagon into the barn for later unloading. Have the round bailer greased/oiled and ready to go. Hook up to it and go back out and finish with the round bailer. Those round bales, if rained upon, should shed the rain much better than square bales
@leol1682
2 жыл бұрын
Like the video Evan , Rebbeca .
@joesphbenwy3845
4 күн бұрын
Done this know the feeling
@grantmagnuson4883
9 ай бұрын
We bailed hay until 10 o’clock at night to keep it from getting rained on and 15%
@3GirlsNi
2 жыл бұрын
Anyhoo..... back to the pond!?? Update vid? The clean up, which fish would be great for fertilizer, or the smell...peww!
@garymcbrien2853
2 жыл бұрын
,a good lesson learned never leave for tomorrow what you can do today
@michellegerrard6623
2 жыл бұрын
Great driving Rebecca 👍
@stevengullison5123
2 жыл бұрын
Good afternoon guys and girls, this is the first time I have ever heard of wire bailing hay. Been around hay all my life, I am 64 years old. They always said you can learn something everyday if you listen. Thank you. Steve from N.B
@hollandduck79
2 жыл бұрын
Hello from the Netherlands and thanks for the video. Sincerely, Hollandduck
@jacktomberlin7976
2 жыл бұрын
I’ve seen some of those hay wagons with a removable stake panel on the back. That might help with bales falling off and give you something to stack against.
@corydriver7634
2 жыл бұрын
You’re right there should be a rack on the back, I have a feeling he may have removed it so it would fit into the barn.
@sroberts605
2 жыл бұрын
@@corydriver7634 There definitely was one, I remember Evan making it. Can't remember why it's no longer used.
@anthonymeyer43
2 жыл бұрын
Any problems with hardware in your stock. I was taught not to use wire tie bails because of the wire causing hardware in the cows
@jacktomberlin7976
2 жыл бұрын
@@corydriver7634 I think he could cut it down to fit the height he can stack the bales.
@CountryViewAcres
2 жыл бұрын
I have to to unload from the back of the wagon. If the hayrack is on, I can't unload in my barn. And I can't remove it with hay leaning against it. So I am forced to run without the hayrack, or backstop.
@lescoe
2 жыл бұрын
Let's hear it for the real MVP here, your spine.
@olddawgdreaming5715
2 жыл бұрын
Back to the shop and get them fixed. Stay safe and catch you later. Fred.
@DennisFahlstrom
6 ай бұрын
Evan, if I were you, I’d find find a new home for that square baler…or I’d hire an expert to go through and tune it up for you if you really need those small bales. You’d be effort ahead and and a much lower frustration level.
@jamesmorrison1884
2 жыл бұрын
Hello Evan sounds like your knotters need some oil. You may try spraying them with wd40 let it sit over night. Nice work have a good evening
@davemcewen9991
2 жыл бұрын
no those machines have grease fittings that should be greased daily and the only other thing needed is clean the chalf out of the knotter assembly, you dont want oil in there it would just build up more chalf .
@jamesmorrison1884
2 жыл бұрын
@@davemcewen9991 Oil works great thanks
@JoeBJones
2 жыл бұрын
New Hollands are top line balers. Don't give up on it.
@philipsmith229
2 жыл бұрын
Check all your wire guides and rollers for grooves may have a roller frozen. Always completely clean ot baler before storing oil wire rolls for storage and dump about a half quart of oil in each box before baling. Rusty wire will cause problems
@sroberts605
2 жыл бұрын
Wow, a lot of tough comments here - these wonderful people have full time jobs! Anyway... good comments about obviously checking the wire first, then the knotter, perhaps the speed. But if the weather really doesn't come good, would you consider making it into silage? (haylage, or baleage). I'm in the UK where we make a clamp and feed silage, and I'm not sure how common that is there. But it would be one way to rescue wet hay and make it into good winter feed.
@Flowing23
2 жыл бұрын
That was hardship, the Bailer not tying. Better luck next time. Well done guys.
@tims6104
2 жыл бұрын
I don't miss stacking hay at all but it is nice to watch you two great people good job
@lorenmeyer5290
2 жыл бұрын
GREAT job Rebecca and Evan!
@justinmiller8562
2 жыл бұрын
Always a bright side to look on..😇 I have had vary good success with a New holland 273 square baler. Twine tie.)
@Pigpen1202
2 жыл бұрын
I have that same bailer and love it. Mine is a 1968 I think. I bought it off my dad. It has been rebuilt but works great
@justinmiller8562
2 жыл бұрын
@@Pigpen1202Awesome man!! Yep there not the highest capacity baler as some of the Newer ones but vary reliable.. I bought mine out of a barn for $900 bucks.. Have replaced a chain and nothing really else I can think of.🤔 Awesome machines..
@jamestillotson1622
2 жыл бұрын
I always found that when I had my farm. That it took a few bales to clear the rust out of everything.
@jvin248
2 жыл бұрын
Your video brings back the memories! We used to bale and stack on wagons like that. When you have one side tied and one not out of the baler, run twine/wire from one end of the tied side around the bale edge and to the other end of the tied side. We called those 'suitcase ties' as you'd pick them up with the side tie and they looked like suitcases. Sometimes that's faster to fix than re-baling but you've got to catch them right out of the chute (and tractor driver needs to pause). Tie the new twine on the top face of the bale and yank it around to the end. Second end thread on the face, yank it to the end, pull tight and tie off quick. If you raise the lower chute plate on the baler you can put the upper/end chute plate at a lower more gentle angle onto the wagon so untied bales get up in once piece. Knotter problems were a big issue for us and taught us some work arounds. There are some good videos on youtube for correctly setting knotters, I think one guy was called the knotter whisperer or something..
@stephaniewilson3955
Жыл бұрын
That left over hay will be a great mulch for your garden.
@guyapeterson
2 жыл бұрын
It's awesome that you guys work together like this. 👍
@marku8175
2 жыл бұрын
A small tip that may help you and your stack problems on the hay rack,,, 1 bale long ways on the side of the rack,,, 4 short ways, start long ways with one on the other side and repeat,, bales will be less likely to fall off and are tied together,,,,,
@markb1487
2 жыл бұрын
Evan,Evan,Evan....This brought back some memories and not good ones...... We used to do around 60/70 acres of small little bales...(roughly around 6000-7000))) small bales....Don't miss this one little bit....Great great content. 💯👍💯👍💯👍
@cleokey
2 жыл бұрын
Wow, I worked on my uncle's farm in Minnesota one summer about 1962 and we used this same basic rake and 2w bailer...I remember the hay wagon coming detached and crashing at the end of the field. We had a reciprocated saw to mow on a little Ford Ferguson
@dylanvanduzer1302
Жыл бұрын
I alway when by if it felt dry it was ready to bake and when I put it in the barn cut side up and always on edge
@michaeldye7202
2 жыл бұрын
I may be late to the party on this one but are you sure there's not a rusty section in your tie wire? If you haven't used it since last year some moisture may have found it's way on to the wire. I have a NH 311 twine tie, used it last year working beautifully. This year first time I used it would break about every 4th bale and twine built up on the knotter. Looked at almost everything except the twine itself. Moisture had run down one side of the twine ball and it was rotten in that spot. Replaced the twine no more problems. I know yours is wire but it's just a thought. Keep up the good work and positive thoughts.
@oldwood4256
2 жыл бұрын
Awesome patience’s Evan . Be well! Roger
@frankeycrawford
2 жыл бұрын
My allergies 🤧 was starting to mess with me jus and buy watching this video but I hope you get the bailer fited soon
@brucemoore2163
2 жыл бұрын
Hay at best is a pain in the ass. Hard work, never enough help and then there’s the rain gods. When hay goes good, rejoice!
@d.j.robinson9424
2 жыл бұрын
I don't know all the mechanics of the square bailer, but maybe try new wire, and check those pinchers or wire cutter.👍👍💛💚
@terrycastor8299
2 жыл бұрын
Rebecca Jean (that's a pure guess on my part) put some gloves on! That wire will eat your hands! Lots of folks liked the wire balers because the wire was useful around the farm for quick fixes, but we always used twine. It had it's uses but could be burned if an excessive amount collected over time. Yes, definitely need to figure out what is causing the tie issue. It's a royal pain in the butt when balers don't work properly. Put a short hayrack on that wagon, Evan.. Even a three footer would help out immensely!
@CountryViewAcres
2 жыл бұрын
I told her to go get gloves. She is stubborn and wouldn't go back and get gloves.
@leahmollytheblindcatnordee3586
Жыл бұрын
@@CountryViewAcres Or shoes. Ha. To each their own. Good luck.
@rudyrivera7426
2 жыл бұрын
Hang in there! Evan and Rebeca! Good teamwork! 👍🙏🏻
@marka6719
2 жыл бұрын
Yep that’s haying. Don’t give out on that old square baler I have a NH 67 string and normally easy to fix. Y’all make a pretty good team buddy. Thanks for sharing
@DconBlueZ
2 жыл бұрын
Thanks for the video, always enjoy watching!
@vickiemeisinger9632
2 жыл бұрын
That was really a neat Baylor, the square one that you used and I enjoyed getting to see it!! I am so sorry it malfunctioned on you just at the last end of your field especially now that your field is now all wet for several days it will cause three times to work! I was very impressed with Rebecca‘s driving, Yes she didn’t miss anything that I can see yeah she picked up that hay!! You guys make a nice team and I always enjoy watching your videos. I’m glad you’ll have enough hay though for the animals as so many people don’t so that’s a blessing❣️❣️
@dennissanders7756
2 жыл бұрын
Here in eastern Okla crab grass can cause fits...it can look and feel dry but still have moisture...love seeing the baler...growing up we had a 78 super hayliner..it had a 4 cyl Wisconcin...sweet sound to hear the governor open when the plunger went back....also good to see yall getting it done...my wife racked many a rd bale...lost her in 02 ..
@jasonmushersee
2 жыл бұрын
the weather fights you every year my neighbor had nh68 hayliner he always manually tied every bale took entire day to make 1 load for me this year worked out good week ahead scheduled 2 days off from off the farm job to round bale then a forcasted 1 3/4" rain actually held off until i finished made shit ton good quality hay no major breakdowns but pushed myself hard got super dehydrated took week to recover everyone at work still pissy mad i took 2 days off
@newinsharpsville
2 жыл бұрын
It could make life a little easier if you build a back stop on that wagon
@rypkepaulusma
Жыл бұрын
Great video. I think the rake could be set a little lower though, I see quite some grass left behind that will have an effect on growth.
@superliner101hobbyfarming
2 жыл бұрын
I love my super hayliner 69 string/twine baler, it works amazingly for its age. I couldn’t agree more however that some days it works flawlessly and other days it mis-ties every other F’n bale!
@oldschoolfarmer7610
2 жыл бұрын
Hi Evan, we had the exact same baler when I was young . We found you needed to keep the chamber full for it to work and knot better. So in a lighter crop you need to drive faster to force the grass in more .This probably explains why it knotted the burst bales better.
@thurlowfamilyfarm4628
2 жыл бұрын
Lesson learned on red clover, and safety pins. Use alfalfa or trefoil in the mix. Your extension service should have mix examples
@christopherhuffman1920
2 жыл бұрын
Rebecca did a nice job operating the tractor. 👍🏻
@aldonboon1728
2 жыл бұрын
My advice on the last field is rent a no till drill reseed that way ! Wire balers are a pain !
@scottbalak7123
2 жыл бұрын
I can't imagine how frustrating that is to see a bale come up and then fall apart in your hands. I've always purchased my hay and moved to round bales just to save on the labor. Load, unload, move, stack, unstack, etc, etc. Hope your round bailer keeps working great for you. Good luck! Love the channel.
@Pigpen1202
2 жыл бұрын
I make my best money on small square bails. And I use small square bails for the horses
@justinbieber12373
2 жыл бұрын
In Farming, never leave for tomorrow what you can do today.. 🍷
@rickfink464
2 жыл бұрын
I was hoping to see you work on the square baler.
@owenpurvis2633
2 жыл бұрын
Love the farmer in flip flops.
@krissyb1980
2 жыл бұрын
Those old square balers sure can be frustrating. Small bales are nice for feeding in the winter and there is not as much waste but round bales are way easier huh? Good work y'all, stay after it
@JL_10acres
2 жыл бұрын
I enjoyed the video. I started watching your videos when I was thinking of starting bailing myself a few years ago. Don’t get discouraged, if you don’t I won’t either. Thanks to you for helping me learn some of this stuff. Also thanks for showing that learning and doing things in life is hard but can also be rewarding!
@josephpadula2283
3 ай бұрын
Too much on tractor , not enough on bailer …. Don’t get a wire bailer this late in the game , but that beautiful round bailer will take care of you . Borrow an old tractor for the day to shuttle the hay wagon to the barn so you don’t have to make the trip with the big one . Good luck guys ! Live your videos .
@josephpadula2283
3 ай бұрын
Love not live
@jonathanbuck6526
2 жыл бұрын
Evan, if you find the time you can fix that wonky tacho on the Case by removing the inner cable and greasing the whole length as you re-insert it into the outer cable. You are welcome.
@garyjohn316
2 жыл бұрын
L@@ks good! You guys have it going on!
@sheilamclaughlin963
2 жыл бұрын
Dump a bucket of used oil over the twisters after the the season and before the start of the season next year, also the wire so it doesn’t rust and pulls easily,red clover is a annual and the grass will come in time
@alolson3359
2 жыл бұрын
One of the first jobs I had as a 13 year old was tying the wire on a hand tie baler, the late forties.
@larryconley9438
2 жыл бұрын
Evan and Rebecca you guys make a great team. I know you will figure the baler out,you have the patience more they anyone I seen on the shows. Great videos keep up the great work
@ronharrison1776
2 жыл бұрын
Sometimes if it wasn't for bad luck you wouldn't have any at all . But you two work very hard .
@karinlotz5732
2 жыл бұрын
If I were you I' d have bailed the day before. We here in Germany work in the fields up to the very dark if the weather forecast is not sure and we sometimes miss supper! First priority always is to bring the harvest in because there is so much effort behind. Maybe this is anorher learn lesson. Many greetings an be safe!
@russellgnuse
2 жыл бұрын
Then your haying you have to go we roll and lot of hay at night when it time to bale you did if it takes late you have to do it never wait because it will rain 👍
@crslyrn
2 жыл бұрын
Oh the joys & aggravations of baling hay. Makes for a long day when the equipment has issues & you gotta get things done. Then Ol' Mother Nature adds her 2 cents. Tedd out the windrows, rerake it, & roll it up then let the cows pick thru them later. Take care.
@aaronmenke5794
2 жыл бұрын
Ahh now I see the hay hook. Lol
@halfwayfarmsandoutdoors3550
2 жыл бұрын
Hard to work with Mother Nature sometimes; especially while having a regular job!! I’m in the same boat as you are. I work in an office most of the time, travel for work for a few days at a time and then try to fit in what I love to do the most- working on my farm. Life I guess.
@MrYkcub
2 жыл бұрын
Even, you might consider using hay hooks for that work on the trailer. They can be a great help once you get the hang of it.
@robertpayne2717
2 жыл бұрын
I always preferred wire tied square balers over sisal grass bales they hold better usally. You just need to fix a barrel by your manger and pop rivet a holster made of an old inner tube to hold a pair of diagonal pliers on the barrel the barrel is used to put the baling wire in. A good set of hay forks are good for handling those wire tied bales.
@ruthkent7190
2 жыл бұрын
You both are very inspiring! Thank you for sharing as you do, keeping faith to complete daily challenges you face. Wonderful examples of what life is truly about. God bless youzzzzz and keep youzzzz in the palm of His hand...
@Cuzifarm
2 жыл бұрын
new seeding always take a year or so to establish a good stand. i know you don't really need a lot of alfalfa but an alfalfa grass mix would work perfect and if you cut at right times you will get 4 cuttings a year. good to plant that new seeding with oats to help establish it. the bad side about just grass fields is slow regrowth. usually only get 2 cuttings a year and 2nd cut tends to be thin.
@pal6598
2 жыл бұрын
I chopped my 2021 second cut into the ground. Had same problem, rained on serval times.
Пікірлер: 293