Your video saved me, I was discouraged and never would of realized the 2 pumping plungers existed and how it works, mine must have been seized up so I ressurected it.
@jesseburns9734
5 жыл бұрын
Thank you for all your videos. I was a marine repairman and I changed jobs. I had been missing the great dealing of solving trouble with machines. I found your vedios and have been able to enjoy the great since of repairing the machine and staying clean at the same time. You do outstanding work. I wish you all the best. Jesse
@agustinfilonenko7835
2 жыл бұрын
la quiero ver desarmada
@johnerway7255
4 жыл бұрын
Warren, the hand sure take a beating in the mechanics trade, just part of the job. This will kick the old guys ass later in life. Hands of a working man. Thanks for the video on this pump.
@laneburgess1643
4 жыл бұрын
I love the history you add to your videos.
@michaeljp86
5 жыл бұрын
Thanks for the video, i just went through the pump one my john deere combine saved a bunch of money.
@fergie35X
6 жыл бұрын
Very interesting to see the inside of a pump. Good for you I guess to have a break from the heavier stuff !
@rafaellyon6808
Жыл бұрын
thanks to your two educational videos I rebulit my 6 cly JD induction pump Roosamaster. Updated weight cage new bushing new vane pump assembly ect ect. Installed it and with the help of a gasoline soaked rag started right up runs just perfect. thx again
@nathanmarsala3099
2 жыл бұрын
Thank you so much for making this video! I broke off the throttle lever on my 1976 Case 480c construction king and was faced with buying a new injection pump or fix the one I had. Found out that I could replace the rod and wanted to see what to expect. This video is awesome!! Thanks again brother!
@mannylangstraatlangstraatf6134
6 жыл бұрын
I'm working on a Stanadyne DB4327 right now. This video helped me out quite a bit Thanks!
@westerntruckandtractorrepa1353
6 жыл бұрын
Langstraat Farms I've got an assembly video too .
@quinnsteeves295
9 ай бұрын
Thank you Warren. Had my first run in with one 9of these today. Leaking from that bottom flat head plug.
@johnerway7255
4 жыл бұрын
Nailed it again guy, super job for us trying to learn. Thumbs up BIG TIME Warren.
@tectalabyss
5 жыл бұрын
Hello Sir. I understand how busy you guys stay. I have a Massey Ferguson 50A backhoe I hoped I had gotten a good deal on.and I wish the pump had been that clean. Mine was full of Sludge under the top cap. It's a DAV type. Had water half way up the lower part. The rest had went inside the motor. Because I believed what the seller told me I tried to start it. I think it messed up all the injectors has it pumped just enough to move the dirt/dried fuel . To say the least parts are putting a hurting on my wallet. : ) May has well laugh about it. Thank you Sir All my best from Tennessee.
@farmerjon1206
6 жыл бұрын
Thank you for making this video as well as all the other ones. Every time we had one of these pumps give us a problem, it cost us between $500-700. Just took one apart today and resealed thanks in part to your video! Total cost: $37
@francoisbouvier7861
2 жыл бұрын
I just paid to have mine rebuilt..$ 1600.00 Even with exchange you're getting a deal.
@jdahling4738
Жыл бұрын
@@francoisbouvier7861was about to say, just had one done for $1300. $500-$700 is a steal.
@patiencepeeler7103
3 ай бұрын
Thank u very much for this husband has a case 450 d dozer he put metering spring in wrong so now when he gets home he can fix it right to get us up running again thank you ❤
@finallyitsed2191
3 жыл бұрын
I have a '96 JD 410D with a Stanadyne pump. It's a little different than the one you have here but close enough. I started losing power where it would free rev then pull back in RPM and absolutely no power to run any hydraulics, etc. I replaced the secondary filter, cleaned the siphon and thought about working on the injector pump next.. that is until I watched this video. I've since decided to leave this to someone who knows what the hell they are doing because if I took it apart it would have to go back in my junk pile. I wish you were my neighbor.
@tordlingvall899
5 жыл бұрын
Take care of your hands with diesel you in the long term can get problems with your skin!! My brother worked 40 years with diesel engines and he get big problems with skin in his hands. So take care. Love your videos!!
@Texaca
4 жыл бұрын
good advise, that also applies to all petroleum fuels, solvents and additives. they are all dangerous, if you have long term exposure to them.
@billreyna1355
4 жыл бұрын
I have this pump. The info/data was worth knowing. Thanks.
@1995jug
6 жыл бұрын
I want to thank you for showing this, I got a jd 2640 that leaking around throttle shaft it runs fine all but that I believe I can put new o ring on it on the shaft on the tractor.
@westerntruckandtractorrepa1353
6 жыл бұрын
joe tiller Yes you can do that on the tractor. Thanks for watching.
@carloswitter9733
4 жыл бұрын
@@westerntruckandtractorrepa1353 hi Joe tiller mi name is Carlos Witter. Have a question? I have a 1975 John deere 410 . Have the same fuel injection pump just li the one you repair on the video. Do you have perhaps the tracking number of the kit you used to rebuild the pump. ?
@hardinelders8457
6 жыл бұрын
Thanks very much, very helpful. Did you make a reassembly video ??
@jjcuna
7 ай бұрын
Many thanks for the upload!
@BurGboy304
7 жыл бұрын
anither great video sir!..very good information and detail into a job like this . keep'm coming buddy 🖒👌🖒
@westerntruckandtractorrepa1353
7 жыл бұрын
Tweaked Diesel 304 Thank you very much, have a good one.
@rafaellyon6808
Жыл бұрын
thank you for taking the time to share your knowledge
@hemiram05
7 жыл бұрын
Great video. Needed to see this as I have a John Deere 1020 that the governor ring is coming apart and clogging the return check valve. Going to open it up soon. Are you going to have a reassembly video?
@CarlJohnson-km8zr
6 жыл бұрын
I have a early serial JD 555A crawler loader, I've got mine off and tore down, waiting on a kit. i'm having trouble finding timing instructions for the 4-276T the timing gear has a keyed slot, and the gear hasn't jumped time or can it with the pump off, so I'm sure I can get it back where it was, I just wanna check to see if it has been tampered with or if it is timed correctly. Having trouble finding manuals that aren't a arm and a leg for..... its amazing the simplicity of the pumps lol $50 and it will be new again
@brendtoconnell6119
Жыл бұрын
Thank you. Had some red material debris inside the pump clogging up the fuel intake and shutting the engine down. Was the large red O-Ring that had degraded and failed.
@johnr8476
4 жыл бұрын
Wonder if he used the special tool to remove the ball that screws into the cam ring? I have never seen one and haven't found anyone that sells them, but I think would have a sleeve or something that would fit snug around the ball to prevent it from cracking or breaking when screwing it out ?
@jeepsolo7218
2 жыл бұрын
Great video. Thanks for sharing.
@cer2451
6 жыл бұрын
Saw another ask about the correct Bristol Wrench size for the timing advance screws...didn't see a reply, can you tell us what size wrench we need. Have read where even Stanadyne is now using a modified Torx bit with a sleeve, but if you can find them, they want an arm & leg for them. Might have the correct wrench, but would be nice to know before I attempt to disassemble the pump. Thanks, great video....would love to see one on reassembly :)
@dennismeehan4986
4 жыл бұрын
I just got done disassembling my roosa master pump awesome video my shaft actually snapped so teardown for cause was necessary video got me to the rollers but my pump is seized one step further how do I disassemble the last part
@roberto052568
5 жыл бұрын
Thanks Cory hohman. The problem turn out to be worse than I thought.the fuel pump needs rebuild. I'd found a replacement close by.
@OldGlory1776
5 жыл бұрын
how similar is this pump to the DB4's in the JD 74/7510 tractors? I have one that is VERY doggy, about 10K hours. Engine runs very smooth and starts well, thinking I just need bump the fuel setting. I had backed out the fuel screw some on the old stanadynes in the 6.2 diesels in the past, but didn't know if the DB4s were a different animal. Hate to get a re-man pump is all I need is a fuel setting adjustment.
@MastPoint
6 жыл бұрын
Just wanted to say thanks! I was able to re-seal my Roosa Master on my 74 JD1530 from watching your video. I'm a subscriber now! A little worried about that half moon clip on my throttle body...it's shaped in a way that my engine cut off uses it to close off the fuel supply and the first few times I tested it the tension popped it off. I gave it a little squeeze and put it back on. If it comes loose at least I'm confident I can take it back apart and fix it! Thanks again.
@westerntruckandtractorrepa1353
6 жыл бұрын
MastPoint 2016 Thanks for the sub , and those clips can be problematic.
@donald1056
6 жыл бұрын
Very detailed
@auwawww2360
5 жыл бұрын
thanks for all the good work, i have a 401c JD - backhoe that uses the same pump and Leaks badLy since the fiLter unit is cracked and Leaking, i wonder if you couLd heLp me find this axact internaL fiLter unit anywhere ?!
@andrewrobinson2869
Жыл бұрын
Great work thank you.
@vasileiosmantikas362
2 жыл бұрын
Great video, I have the same pump, I was wondering if you have any advice, or videos on replacing the fuel shut off solenoid
@michaelmccaffrey2731
3 жыл бұрын
I made six trips to get a compartment latch from Warren Cat in Tulsa and five trips for a seal from John Deere. I thought getting parts in California was bad until I moved to Oklahoma.
@heavychevy2289
6 жыл бұрын
I came across some Db4 and Db6 pumps that have failed in some mep series generators due to low fuel lubrication properties.
@shawnllorca4768
3 жыл бұрын
I think I might have one at the moment on an 805B
@jasonmarien2793
7 жыл бұрын
Great video! My buddy has an old 440 skidder with the alike pump hope to never have to rebuild. Keep up the good work. What would your suggestion be for keeping the pumps from frosting/jelling in colder weather.
@westerntruckandtractorrepa1353
7 жыл бұрын
Jason Marien Well around here when it gets into the 0 to - numbers we use that diesel 911 or run #1 diesel, I have seen some guys run straight kerosene which I wouldn't recommend.
@jimball816
4 жыл бұрын
am getting ready to do a cav dpa this winter. a rebuild video by you would be appreciated. thank
@DaveSmith-nr2lb
Жыл бұрын
Great video was wondering what you charge to rebuild this same pump. I have one on a 410 backhoe. also have a question about my problem. I think I should be able to hear the solenoid move the shut off when 12 volts are applied, also if I crank the engine with the fuel lines disconnected at the injectors I would think I should see fuel come out the lines, I do have fuel pumping at the pump input. I think this tells me my pump is not working.
@danthompson524
4 жыл бұрын
I have a 73 case 580b 188d engine. I had the engine rebuild an right after we fired it back up I ran out of diesel an fueled it back up an did the same thing. An what I found out is that it dumped all the fuel in the crank case. Trying to figure it out if it's a bad injector or the o ring on the pump shaft
@tyroneburton1918
4 жыл бұрын
I know times are changing I’d like to see you do a old mechanical Cummins or b/c /a injection pump thanks
@FarmerTanTerror
6 жыл бұрын
How do you keep the timing for reinstalling it?
@maxpuppy96
4 жыл бұрын
those pumps are bullet proof, I have a couple on JD's 4045's
@bruni5289
4 жыл бұрын
The P7100 injection pumps on the Twelve Valve can make some serious power though
@drfarpella
3 жыл бұрын
Good morning, just ran across this video, I have an 70's JD 310A 3cyl diesel, im assuming the pump is pretty similar, the pump in this video looks identical aside from the fact mine is a 3cyl,my question is,when I start my tractor,it takes off,goes right to high throttle, my linkage is all the way forward as it should be for idle,any ideas??? Thanx in advance.
@jerrysteele6427
6 жыл бұрын
Can you tell me what the timeing setting on a 310G case
@georgebell3964
3 жыл бұрын
Great video
@gooseneckposse240
6 жыл бұрын
We have a JD300 tractor with this type pump...how can we test it to see if it needs rebuilt. The engine starts & cuts off. Thanks
@ericlakota6512
3 жыл бұрын
That is what i do when i work on stuff i but it in order where it goes like when you took the throttle shaft out one les thing to remeber ill never turn around and lay stuff on the flat the way it came out
@darkjedi7083
6 жыл бұрын
I have the Stanadyne DB2 pump on my 7.3 idi t. Works good but as far as I no it's never been rebuilt and just turned 200 thousand on the clock. Would love to freshen it up.
@westerntruckandtractorrepa1353
6 жыл бұрын
Yeah , I would say you are about due .
@ethantracy337
6 жыл бұрын
I have a JD 820 and the throttle is sticking at a single rpm. No throttle response and would not shut off. Do you think I may have a gov, or weight basket issue?
@adventureswithjosh7914
4 жыл бұрын
Hello western truck, Thank you for the video. I'm wondering if you'd happen to know the voltage required for the fuel shutoff solenoid or better yet where that should be connected to? I have an 1974 Allis Chalmers HD4 I am trying to revive and there is currently nothing attached to the post you mentioned. Any and all help would be greatly appreciated.
@newjerseybill3521
4 жыл бұрын
The Roosa Master / Stanadyne pumps came 4 ways. Energize to run, energize to shut down, 12 Volt coil and 24 volt coil The most common wiring is connected to the switched hot terminal of the ignition switch. Then wired to the pump as shown @5:30
@tonyaiello6463
3 жыл бұрын
Wow. You really know your stuff. Could you rebuild mine from my case 580c backhoe?
@bfe671
6 жыл бұрын
Did you do the reassembly video? I can't find it on your channel
@Rossco139
3 жыл бұрын
kzitem.info/news/bejne/q36ttZ1jo5yhe5w
@danielholby2466
2 жыл бұрын
Question, I have the same injection pump, the flex ring failed. Ordered a seal kit and replaced the flex ring. Cleaned and inspected the parts and didn't see anything else wrong. Reseal, reassemble, exactly how I took it apart. Reinstalled injection pump on my machine. It will run for a min and stall out, let the machine sit for 30 seconds and it will start and run for a min and stall out again. The lift pump is good, and nothing in the fuel tank that is restricting flow to the transfer pump side of the injection pump, shut down solenoid is working. I did pull apart the rotor from the body and seen 2 screws recessed in the body. Didn't remove them, is it possible a piece of rubber from the old flex ring is stuck in there? I'm out of ideas. I was thinking that the shut down solenoid was drifting but when the machine would stall i wouldn't cycle the key, just push the starter button.
@luisbonilla2386
3 жыл бұрын
I got the same pump but I still have the drive shaft inside the pump how do you take it off to replace the seals?
@fredblase5608
4 жыл бұрын
to help get the hydraulic head out use a coupla 3-8 fine thread bolts for levers use same bolts with nuts on then to get the head back in place with out getting it to far and cutting the o ring around the head
@johnwaby4321
4 жыл бұрын
That looks a fiddle job 👍
@Flyboy207
5 жыл бұрын
Hey there, I've got a pump like this one on an old generator. It has a fitting that sticks out of the back of the upper throttle housing and points toward the fuel inlet, it has a knurled cap that looks kind of like a thimble that you can twist with your fingers, any idea what that is? Thank you, great video for us getting into pump rebuilding
@xade7863
2 жыл бұрын
Sounds to me like u got a cav Pump instead of a stanadyne and that’s to adjust your rpm
@comet4242
4 жыл бұрын
you mentioned you were making the video of assembly but I cant find it
@AD4203
6 жыл бұрын
How did you get the bristol screw (timing advance) on the bottom of the pump out an what size was it
@cew995
4 жыл бұрын
That is my question also
@gerlandkent6377
Жыл бұрын
thank, you for you're video. I, have a question for you. I've got a 1966, case 530 Diesel Backhoe. My Diesel pump stopped pumping fuel to the injectors. I, took the pump apart and notice why it stopped pumping. the steel shift broke in half inside the pump. it's a clean break in half. It also looks rusted inside of the pump.. could this pump be rebuild or what. thank, you.
@janicebarket2470
6 жыл бұрын
Just what we was looking for. We have a Franklin log skidder with an Allis Chalmers engine. 3400 leaking gas. Could it be an O ring? Thanks!
@dustingarber3213
5 жыл бұрын
What is the tool part number to bull the actuator out looks like a torque bit but. Not?
@tannerdavis1045
4 жыл бұрын
Is this part an electric shut off to the fuel also?
@BoomhauerWorldwide
5 жыл бұрын
Great video, I have a JD 5520 appears to have a failed injector pump. Solenoid is getting 12v and clicks. Inlet is getting fuel and pump is bled. No fuel out of any cylinder port while we crank.
@westerntruckandtractorrepa1353
5 жыл бұрын
Need to pull top cover and see if metering valve is sticking
@BoomhauerWorldwide
5 жыл бұрын
@@westerntruckandtractorrepa1353 my thinking exactly after watching your video. Trying to find a security torx for the bolts now... Thanks a Lot!!
@BoomhauerWorldwide
5 жыл бұрын
Stanadyne used FIVE point security torx bolts on my solenoid, didn't know there was such a thing. These newer JD tractors are like working on a Mercedes
@bryanbetournay5557
Жыл бұрын
Do you have to time the engine before taking off this pump?
@richardowen252
5 жыл бұрын
Hi Great video. I am about to tackle a pump rebuild for an older Case 580 D which I think the rubber flex plate for thee governor wights has deteriorated and is breaking apart, and clogging the fuel return in the pump. Did you make a follow up video to pump the pump back together? I searched for it, but was not successful. Thanks agian for taking the time to make this video. Rich
@westerntruckandtractorrepa1353
5 жыл бұрын
Yes. There is another stanadyne video on assembly of a pump
@dakotak8437
Жыл бұрын
Some reason when I'm bleeding to the injectors only one does not seam to get as much pressure but the others squirt out just fine any ideas and making 1 injector not working great does a little flue but nothing also on the return form injector
@jimmyz003
7 ай бұрын
Did you make the re assembly video? Great info. I'm about to tackle my first stanadyne dB 4371 pump, and it is a bit intimidating
@HudsoniteJessie
Жыл бұрын
How much side to side play should there be in the driveshaft? When it's in the engine, I can grab the gear and wiggle it a bit. It works fine otherwise.
@michaelreynolds7168
2 жыл бұрын
any videos on the 4.5 powertech with factory injection pump on it from deere
@danthompson524
3 жыл бұрын
Do you have a video of how to take one of those out of tractor.
@bop38871
6 жыл бұрын
Where are you located at Ive got one of these pumps on a jd410 that's giving me fits if your in my area Id like to maybe see if you could help out.
@westerntruckandtractorrepa1353
6 жыл бұрын
+bop38871 I am located in Klamath falls Oregon. Where are you?
@BartHull
2 жыл бұрын
So what generally happens when you get a bad tank of diesel and it won't start up again? Gummed up metering screw that fights against the governor spring? I put two new filters on it last time the pump was "rebuilt" and it started fine and ran well, but again will not start like it has no fuel. Suggestions appreciated.
@xade7863
2 жыл бұрын
Prolly scored plungers from water
@marvinfisher6388
2 жыл бұрын
I have a db2 4086 from a generator not sure I want to do this myself I've started but still haven't got the head off.. would you be interested in doing it? It won't let fuel in since it's been sitting for awhile something must be stuck.
@kathleennawalt9855
7 жыл бұрын
Dear Mr. Grease, There sure ain't no mechanics around like You any more. Would bet Your as busy "as a cat covering". Those walking beams sure are a JOB. Off road is tough on them. Thank You for the video. Sincerely, Kathleen.
@westerntruckandtractorrepa1353
7 жыл бұрын
+Kathleen NAWALT Thank you, and good to hear from you.
@bhcontracting
6 жыл бұрын
Great video. Question Im working on the same pump except 6 cyclinder. Im getting great fuel to pump but cannot get fuel through pump to prime. Any suggestions on what is stopping fuel from entering pump.
@westerntruckandtractorrepa1353
6 жыл бұрын
Sounds like something on the inlet is restricting your fuel where the end cap is by the internal gear pump is . Make sure all that is in there correctly or it won't allow fuel into the pump .
@user-gy1do5py9r
8 ай бұрын
Is there a follow up video showing the reassembly?
@timstanford3443
7 жыл бұрын
Great video! where do you buy seal kits from for the cav pumps? I have a pumping head that has too much leakeage and am in need for a pumping head. Do you know where I can source one of those? Thank you my friend and I am glad to finally see another one of your awesome videos!
@westerntruckandtractorrepa1353
7 жыл бұрын
+Tim Stanford I have been getting my parts from Star Diesel and U.S. diesel. You can try your local fuel injection shop, I haven't had much luck with that.
@timstanford3443
7 жыл бұрын
thank you sir! I will check with them
@ramseycoltrane9198
Жыл бұрын
I’m not sure if you responded to these messages but I have recently bought the same tractor with the same injection pump it has fuel to the pump but not after it I believe it is just clogged what would be the best way to unclog it
@boronin10
5 жыл бұрын
Does the rebuild kits you buy for these stanadyne have multiple rubber O rings and metal washers mine came with came with more than I need or are they universal kits
@westerntruckandtractorrepa1353
5 жыл бұрын
Yes , there will be more than you need because that pump was made for multiple applications.
@maxwellwilliams7357
2 жыл бұрын
I am having trouble timing 450c injector pump any suggestions I installed new injector pump and alined dot to shaft and dot in pump primed but will not crank
@reltcl1995
Жыл бұрын
Yes sir I have a 1986 case 580d backhoe and it's a vacuums line coming out above injector pump from intake can you tell me where it might go Thanks Ronnie
@WardEnterprises
6 жыл бұрын
Man I’ve got a like 86 John Deere 450c dozer that is having fueling issues after it gets warm (about 10-15 min). Do you think it could be the pump going out? I’ve changed the fuel filter and it’s for sure a fueling issue not an overheating issue Bc the old dozer doesn’t have any of the stuff to downspeed the engine when it’s hot it’ll just blow the engine.
@shanonearls6945
3 жыл бұрын
I'm having what sounds like your same issue. Can I ask what you figured out ?
@ryanr8979
4 жыл бұрын
How much do u charge to ree man. One of these i have same one i need done
@cobrasvt347
5 жыл бұрын
Ya know your history 👍
@JohnDeere-Lanz310
5 ай бұрын
Hey. On my John Deere there is this injection pump installed too, but for 3 cylinders. My question is, how can I adjust the injection quantity?
@rodrigoantioco8704
3 жыл бұрын
Hello sir i got a stanadyne pump on a tmd27 continetial engine problem is im getting fuel to the pump its not sending fuel out like at all what could my problem be ?
@ButchE30M3S14
2 ай бұрын
I have a Stanadyne for a 6cil 282 engine, but it has old fuel and crud at the bottom. How do I drain these pumps on the machine so I can put fresh fuel in it? Thank you
@USoutdoorsman
3 жыл бұрын
Maybe yall can help me. I have a 66 John Deere JD400 backhoe and its missing the injection pump. I’ve heard its a roosa c model but i have alot of trouble finding any information or parts if you could provide any info that would be great!
@Butch-hs9tt
5 ай бұрын
I have a 580c case backhoe how is it to take off pump
@RuralTowner
7 жыл бұрын
Have a DB pump that looks identical on an 81 Waukesha//Miller welder. Replaced the old solenoid which would bind up and require FIRM tapping on pump to get it to finally shut down. Not sure If I'm getting the hooked foot on the solenoid lever into place correctly. Powers up but still not getting fuel to bleed the injectors since they lost their prime when I had to pull return lines from #1 and #2 to access the top cover.
@westerntruckandtractorrepa1353
7 жыл бұрын
RuralTowner Yeah I think you are on the right track, sounds like the foot is not letting the metering valve open to allow the fuel into the pump head.
@RuralTowner
7 жыл бұрын
Saw another newer Stanadyne pump that was a cut-away but the upper works to have the same upper workings...that foot hooks around at tab on the slide below it? If not working the slide then no fuel will flow through the meter. When I put the top straight down I think what I was feeling was the plunger being partially depressed as the foot was pressing then missing its place leaving the solenoid to go through its motions and nothing else This is an admittedly simple ordeal I imagine...just replacing the solenoid but this is my 1st foray into IP internals.
@westerntruckandtractorrepa1353
7 жыл бұрын
RuralTowner It should go right on the front side of the tab , don't worry about the simple ordeal, I have been there many times.
@RuralTowner
7 жыл бұрын
Thanks. I remember now that when I first removed the top it wouldn't go straight up...had to move it sideways slightly and after removal I heard a soft "pop" which would have been the slide moving as far as its spring would allow. Had to re-watch instructordave111's "Be the Fuel" several timews where he used a cut-away before I saw the tab. Being only able to see it side-on left me wondering.
@RuralTowner
7 жыл бұрын
Okay the foot doesn't want to hook around that tab. Even the old solenoid foot wouldn't fit around it But I think I figured out how this particular pump behaves. The slide is spring loaded so when the solenoid powers up the slide pulls back on its own to permit running. Powered off the foot presses on the tab and presses it back to shut down position.. Got it running but am back to the same issue I was starting to have to start with...when I power off the engine will still stay running...but at somewhere between 1/2 to 3/4 at what it would when the solenoid is powered up. The slide seems to be sticking as well because when I tried to work it by hand...at first it was stiff before freeing up. Since the solenoid functions with sharp engage//disengage I think it is jamming. Takes some tapping on pump to get it to shut down fully. Could it be I just might need to open the foot up a tad wider to ensure it hooks around the tab (with a little room to spare) so the foot works the slide fully? EDIT: Was later than wanted before got to it. I think I might still be missing out on something...
@Rossco139
3 жыл бұрын
Our 1256 is leaking diesel into the oil and we are thinking that the pump needs to be rebuilt...does that make sense??
@jasondillon3299
3 жыл бұрын
I got a 62 John Deere tractor backhoe can't seem to find any info on it injection pump
@freeride202
4 жыл бұрын
The pilot tube most likely got damaged from running the pump loose.
@jaroslawrogowski3642
3 жыл бұрын
Hello I’m tying find AR43204 pump. Would you be able find one and rebuild? Is off JD644 Thanks
@stevehuff2088
6 жыл бұрын
Great video. I'm retired from Komatsu mining and I have a DBGVC429-4AF pump off a John Deere 3010. There is a leak coming from around the seam where the vane pump is set in the housing. I'm having trouble finding the correct seal kit. Any suggestions.
@westerntruckandtractorrepa1353
6 жыл бұрын
Call Scott @ Oregon Fuel Injection 1541-773-8669 and give him that # and he should be able to get one for you .
@stevehuff2088
6 жыл бұрын
After completing the seal change out, does the pump require calibrating?
@stevehuff2088
6 жыл бұрын
I'm going to call Scott @ Oregon for the kit. Mostly I want to replace the seals... I'm a little nervous about torque specs when reassembling the pump. Any suggestions. Pump is a DBGVC429-4AF from a John Deere 3010.
Пікірлер: 253