Lo veo malo por q el metal riesgo por cambiar temperatura puede dejar de ser flexible ponerse rígido y allí se quiebra ese punto lo mejor es amarrar con lo q sea solape un barra de 50 cm y el cemento lo amarrados en frío sin perder propiedades química del metal por ser un trabajo e frío
@pacovillaperez4386
2 жыл бұрын
Estoy de acuerdo con Tigo mejor atar con alambre más seguro soldar en frlo no te da ninguna seguridad atar con cable y después el hormigón agur desde el básque country Ondo pasa.👍🥳🤐🤬💥💥💥💥
@luischamorro7268
Жыл бұрын
Eso no lo hacen porque se le ocurrió a un obrero, es y debe ser un procedimiento estandarizado ya y testeado por control de resistencia de materiales, sino para qué engañarse
@SaradisN
2 жыл бұрын
I am a Greek civil engineer & we build buildings to withstand earthquakes up to 7-8 Richter. Never seen this before! Not reliable method!
@Rokomarn
2 жыл бұрын
Never seen before ≠ Not an appropriate method
@jesussandoval9042
Жыл бұрын
Esa técnica se ocupa en México para aterrizar (conectar a tierra) un poste de concreto que se "viste" con cables de media o de alta tensión
@vasiliy_sent9490
2 жыл бұрын
Не многие поймут, сколько работы у этого чела☺️💪
@mdehsanulhaque392
2 жыл бұрын
Technology 2021 for the Generation next
@DeepDep1
2 жыл бұрын
Как колпачки одевать.. только медленнее.🤣🤣👍
@alexandrgansky156
2 жыл бұрын
@@mdehsanulhaque392 ванная сварка. Мне ещё в 1970х в техникуме рассказывали
@alexandrgansky156
2 жыл бұрын
@@DeepDep1 надёжность разная
@weldermusk8860
2 жыл бұрын
@@alexandrgansky156 Термитная сварка.
@tobyallen1775
2 жыл бұрын
I'd stagger those welds, I imagine if you bend that,the weld will shear right off. A106 rebar here in the us is made for welding, it's significantly more expensive. If this is just "rebar" you're creating a point of fail.... much weaker than a tied lap.
@iamyou6555
2 жыл бұрын
Agreed they would’ve been better off with a standard lap. Waste of money and compromises the structural integrity shear is a problem especially for that bar mandrel size.
@BanneroftheSun
2 жыл бұрын
I’d stop you at here in the u.s. because their infrastructure is incomparable to that of Japan and China
@adonis190911
2 жыл бұрын
This is how you cut cost lmao even down to a construction, hence why buildings dont last as long im guessing.
@nayogomez
2 жыл бұрын
They should hire you to do better.
@sulcaproducciones2537
Жыл бұрын
Precio
@southernstar4353
2 жыл бұрын
And here you see a perfect example of why theres so many videos of chinese buildings collapsing.
@webysoe9652
2 жыл бұрын
@Southern ,you are very smart and very intelligent and high IQ ,that place is KOREA .
@southernstar4353
2 жыл бұрын
@@webysoe9652 thanks for the compliments my friend, my point still stands 😉
@webysoe9652
2 жыл бұрын
@@southernstar4353 you are welcome Mr knowledgeable, American and Spainish ,must be the same then .good to know that .I would love to learn more from you .plz .
@southernstar4353
2 жыл бұрын
@@webysoe9652 what would you like me to enlighten you on friend?
@webysoe9652
2 жыл бұрын
@@southernstar4353 thank you , maybe if you could posted the video ,how many building collapsing ,( not by demolition , or war ,or by bombing ,nor earthquake, non of that ) something like what happened in Miami Florida ,) or the best Boeing made by your country that kept crashing down .I would like to see that .since you are so well informed ,some thing I could learned. Mucho mucho appreciation amigo .Gracias hombre.
@allfooballgoals
2 жыл бұрын
Those points can turn to be field points. How will the loads be transferred to to the next bar below.
@deepushing4293
2 жыл бұрын
Like no
@shenjiejason8350
2 жыл бұрын
I thought the bar is only meant to be tensile support, the concrete will take the compression load.
@benoit-pierredemaine3824
2 жыл бұрын
This is thermite. It's used to join train tracks. 100% confidence the join is stronger than the bar.
@karlquiah1260
2 жыл бұрын
Did you ask how the load would be transfer below? Can't you see the top bar is sitting on and vertical to the one below? Yiu are thinking textbooks instead of being practical.
@daviddarkman5628
Жыл бұрын
But there is no shear load on a point load weald that's why steel fixers over lap the rebar no wonder the structures fail over there wow
@salvadormota5313
2 жыл бұрын
Se deben soldar con un traslape de mínimo 40 diámetros ya que soldados a tope (punta a punta) no es recomendable.
@shuipingwu1316
Жыл бұрын
建筑主筋不能対焊,搭接焊
@eunlawon5290
2 жыл бұрын
Wrong technique. Welding weakens the temper of the steel bars. Coupling is best
@celiogomesdearaujo2624
2 жыл бұрын
igualzinho no BRASIL.
@dixiehandyman
Жыл бұрын
Who cares this is only a support for mortar or block. It works together with the concrete etc not independently.
@ShaunHensley
2 жыл бұрын
This must be why all those buildings in China keep falling down
@bryandavis9731
2 жыл бұрын
Tungsten a crude but effective Weld.Going old school that’s awesome
@nick.sadovyy
2 жыл бұрын
Оригинально однако! Успехов Вам и всех благ, здоровья и долголетия!
@tonypucheta354
2 жыл бұрын
Me gusta trabajar en la construcción, 8 horas se van volando y nunca dejas de estar con tu mente ocupada
@TriggerFull
2 жыл бұрын
Gracias por responderme, antes de yo preguntar, haha Que bueno que la pases bien, Felicidades. Y BENDICIONES.
@vicentepalacios8598
2 жыл бұрын
Eso es porque tú trabajo te apasiona y es lo que siempre habías buscado ánimos saludos
@alfsierra857
2 жыл бұрын
Qué bien por ti que disfrutas tu trabajo. Además te ayuda en tu acondicionamiento fisico. Felicidades.
@antonioalvarado299
2 жыл бұрын
A mí también me gustaba hasta que me hicieron descargar dos trailas de cemento solito 🤣🤣🤣🤣
@humbertoflores2545
2 жыл бұрын
Que bueno, se nota que te gusta tu trabajo.
@nonig4907
2 жыл бұрын
All spliced at the same hight at least they’ll know where the structural damage is gonna acure
@robertbrowne4049
2 жыл бұрын
They should be overlapped
@lsimpson6223
2 жыл бұрын
They should have staggered the outer perimeter joint by a foot, then staggered the inner set of rear joints by a foot,but start one bar right (or left) so staggered front to rear and left to right. Still gonna change the metallurgy in the rods. Specs on new rod, created in a controlled environment & process is precise. The bonding joints are not all timed precisely, pressure could vary, wind increase cooling. Lots of unpredictable variables
@rustysmith5809
2 жыл бұрын
Right. Staggered joints is a plus on everything.
@ronnierabell1
2 жыл бұрын
Here comes the youtube rod buster engineers 🙄 ever thought that a solid piece is better then a piece of tie wire? And the weld is stronger then the actual steel because the flux removes all oxides and the weld creates a alloys. Not like the tie wires that usually falls apart when the tower crane pick them up and sometimes fall bellow on workers.... Happened to me twice 🙄
@rustysmith5809
2 жыл бұрын
@@ronnierabell1 using tie wire also allows some flex in the concrete. Thats a good thing.
@user-pt8iy9ks1o
2 жыл бұрын
А, китайцы... Опять горбатого лепят. 😋🇷🇺
@user-cm7iw8nc9i
2 жыл бұрын
А рашку китай хорошо вые.бал!
@StaLiN-Ussr.
2 жыл бұрын
@@user-cm7iw8nc9i причем тут Сербия 🤔
@user-ug2yo2us9r
2 жыл бұрын
Потому что гладиолус
@jajangeffendi6398
2 жыл бұрын
Saya salut sm pekerja kasar yg sangat menikmati pekerjaannya dan tdk takut dg aliran listrik good jobb
@jaysenbrady713
2 жыл бұрын
There’s no way this doesn’t weaken the steal around the joint. Anybody know why they don’t overlap and tie like in the states?
@bigjumbo9479
2 жыл бұрын
Yeah and in uk. 6 inch overlap and double butterfly with tie wire....
@4o4err0r.
2 жыл бұрын
@@bigjumbo9479 I’m California is 3 foot over lap
@Tman0517
2 жыл бұрын
MINIMUM 3 foot overlap with 4 tie points in NY. This "weld" looks like a shear point if too much stress was applied in that one section.
@shiroamada1650
2 жыл бұрын
30D-50D as D is the diameter of the rebar. Usually client request 45D. More than 36mm need to use spiral or welding.
@etvon32
2 жыл бұрын
China
@user-cd8tc5vs6w
2 жыл бұрын
Э, брат, нельзя арматуру варить, тем более в стык. Только вязать с нахлестом..
@user-hw7ig4vd8p
2 жыл бұрын
Где тебя этому учили, брат? Проекты нужно иногда смотреть.
@user-mg6ni5mr6g
2 жыл бұрын
@@user-hw7ig4vd8p правильно он говорит. Только с небольшой поправкой: Смотря какая это арматура и на что она работает..
@sergeyalentyev6651
2 жыл бұрын
На работе обслуживаю сварочную машину МСО-606. Она как раз варит арматуру в стык. А вяжут арматуру тогда, когда одна находится в горизонтальной плоскости, другая в вертикальной. Это для армирования фундамента.
@ebu_mozgi_nedorogo
2 жыл бұрын
Я чё то сначала тоже прихуел, спросони не сразу вспомнил. Я не прям мастер по фундаментам, изучал для себя, так вот да, правильно, обычно сваркой не пользуются при сборке арматуры. Но, представь, где то даже не армируют! Все зависит нагрузки на фу, от типа грунта, от уровня грунт вод, от годовых перепадов температур, погодных условий, фазы луны и ещё чего то... Так что и так сойдёт) а встык получается меньше расход Ме, экономийа!
@MsAlmazka
2 жыл бұрын
@@ebu_mozgi_nedorogo ты ж Барсик, откуда тебе знать?
@dandanenad
2 жыл бұрын
This weakend the tensile strength of bars.. it's better to use coupler..
@fritzmiller9792
2 жыл бұрын
So much speculation on this being a cheap method... Well maybe it's a superior method. As long as the Cad Weld he is doing doesn't weaken the steel , it should be as strong as an unbroken length. I would like to see 3 lengths Cad Welded together like this and then bent from the ends into a U shape. That experiment should be very revealing.
@PreservationEnthusiast
2 жыл бұрын
Or you could just lap the bar 40xdia for full tension lap. That's much cheaper
@blong2898
2 жыл бұрын
People who build the world around us are hardly ever appreciated enough and I say this watching this man apply his skills to take part in erecting a build... big props!
@calinross3410
2 жыл бұрын
But what skill is he applying. Using his hands and a bit of common sense.
@stn7172
2 жыл бұрын
That's not skill
@calinross3410
2 жыл бұрын
Thank you
@bobbrereton4785
2 жыл бұрын
I saw this done by quality steel fabricators when I was a union carpenter. I think they were called Caldwell and nicknamed Hot Shots. Useful when too much rod might burn the false work.. Probably better than you think.
@rakape786
2 жыл бұрын
Aluminothermy that's what it is
@ujarachaman6305
2 жыл бұрын
Waoo saving overlaps steel cost!!! Amazing
@AltafHussain-bz3yz
Жыл бұрын
Hahaha no good
@jorgeemiliogodoy2286
Жыл бұрын
Yo trabajé 12 años en ese rubro de enfierradura en 🇨🇱 llegando a ser capataz o jefe, Y a mi criterio no se debe soldar el empalme ya que con la temperatura producida se debilita la resistencia del acero y no cumple las normas antisísmicas mundiales 👍✌️🇨🇱🍀
@paulpz04
2 жыл бұрын
I can just hear my boss now yelling across the yard at the dude in the background in the black jacket and yellow hard hat - .."hey!!!! I don't need anybody to stand in place and watch if you ain't got nothing to do GO HOME!!"
@walterfoster5682
2 жыл бұрын
I think he's the foreman, but I wonder why they didn't just start with longer rod to begone with?
@nivedhsunil9406
2 жыл бұрын
🤪🙏🤯
@davidzwicker5662
2 жыл бұрын
I’m guessing not a union job ( sneakers ) or there would have been a couple more people watching
@sidknee4975
2 жыл бұрын
I’d do all the outside ones first to minimise burn risk and I’d also use an exact measuring cup then you could pour the flux without looking.
@markdodd1152
2 жыл бұрын
Some sort of goggles to protect from flash burn would not be a bad thing.
@brianpierson7708
2 жыл бұрын
For one it’s submerged arc so u not getting flash burn the lil spark u see is less than a cutting torch is giving off and it would take you longer to do one side than than he is doing the hole thing and there’s no exact measurement for that u fill the cup wince it’s dun u take it off and the unused flux drops into the pan and you keep on going plain and simple I’m not saying you can’t do it the way you are suggesting but I’m saying if there was a way to do it faster then you would be watching it and not this one look around and what they are doing and all the ones working on the job I can say if it wasn’t the fastest way and most productive way of doing it that man wouldn’t be working for them doing that job someone who can do it faster would be the one doing it
@markdodd1152
2 жыл бұрын
@@brianpierson7708 good to know , thanks
@tunghansen7260
2 жыл бұрын
How about put the correct bars in the first time and avoid doing this. Not allowed in my country heat compromises the integrity of the bars.
@benoit-pierredemaine3824
2 жыл бұрын
Thermite is used to join train tracks and does better join than the bar itself. The measuring cup is the receptacle itself. Yes googles are heavily recommended.
@jpolish420
2 жыл бұрын
Pretty hilarious when he could have tied it and been done much faster, and it wouldn't fail. Rebar is the junkiest of metals and it is never recommended to weld it. Fail.
@A7exandersca7es
2 жыл бұрын
"tied" it?
@benoit-pierredemaine3824
2 жыл бұрын
Thermite is used to join train tracks and does better join than the bar itself.
@jamesharrell4360
2 жыл бұрын
A106 is
@padie71
2 жыл бұрын
@@benoit-pierredemaine3824 termite even brought down building 7 and the twin towers, so I agree it's strong enough
@Maudires.
2 жыл бұрын
@@padie71 underrated comment that won’t get the thousands of likes it really deserves. If more rational, logical thinking humans existed in this realm the blatant lies and fallacies they feed us on TV and social media wouldn’t be accepted so blindly. I don’t see homeless people dying on skid row in LA from Covid. I don’t homeless people on the street begging for a respirator or coughing from Covid. Ignorance truly is bliss and they control everything from our monetary system to our public educational system. They say we are shooting out across the galaxy at 1000’s of miles per hour, spinning on our own axis, circling the sun… yet the stars have never changed for eons and the Sumerians, Egyptians, Aztecs and Mayans all mapped them and used them for traveling across our realm. Everything is a lie. This is the matrix.
@jenirambrothers2781
2 жыл бұрын
Most comments here dont know about this procedure..As per the Structural Welding Code AWS D1. 4, a low-alloy steel rebar is weld-able. This grade of rebar has a steel-to-carbon ratio that makes it suitable to be welded. Not only is it suitable for welding, but the welds can stay together under significant load after it has been sealed in concrete. Most of Japanese building constructon used this kind of procedure.
@TheAlbert1A1
Жыл бұрын
Exactly, A706
@dorsebradford9844
2 жыл бұрын
Maybe it’s a safety thing ? No idea why none of the bars have any caps reminds of that show with the crazy accidents where the guy had fell on rebar right through his eye socket
@beanmeister4951
2 жыл бұрын
A Thousand Ways to Die?
@dorsebradford9844
2 жыл бұрын
@@beanmeister4951 Nah this was a emergency room show on discovery channel hold up I’ll look it up
@dorsebradford9844
2 жыл бұрын
@@beanmeister4951 his name was Ron hunt and he fell on a 18 inch drill bit right through his eye socket and survived he fell off a ladder and landed on a drill maybe a hammer drill idk what type of drill that happened in 2006
@kevin6030
2 жыл бұрын
it's f****** China man they don't care if they live or die as long as the government makes money
@arthurconanrus9801
2 жыл бұрын
Этому способу сварки восхищаются те кто не понимает в стройке и физике сварки материалов. В месте сварки, тем более встык, конструкция конкретно ослаблена. Понятно, что бетон может стоять вообще без арматуры, но ради чего тогда огород городить?
@user-mg6ni5mr6g
2 жыл бұрын
Терзают мутные сомнения в правильности того, что он делает... 1. Варить в стык арматуру к арматуре, которая работает как на изгиб, так и на растяжение, где то и на крутящий момент - навряд ли длина точечного шва расчитывался на сочетание этих нагрузок.. 2. Когда варят таким образом что-либо встык, соседние стыки в одной конструкции должны быть сварены вразбежку, т.е. ни на одной линии. Но! Исключение: если лабораторные испытания показали, что прочность на растяжение, изгиб и срез такого сварного шва = ровному участку арматуры.
@luisangelarguedasfuentes303
2 жыл бұрын
La inteligencia humana no tiene límites
@pelukabassman7453
2 жыл бұрын
NO SE PUEDE SOLDAR HIERRO DE CONSTRUCCIÓN ES UNA LOCURA
@guillermofigueroa3609
2 жыл бұрын
Todos soldados a un mismo nivel y en la misma columna!!! Muy mal!!! Además que el fierro de construcción no se solda!
@johnfgallegos1477
2 жыл бұрын
Pero me parece que no es soldado es como una fundición que está haciendo.
@BobbyOfEarth
2 жыл бұрын
Interesting that he's using the same method used to weld all the rails together for a highspeed train.
@legaitkl
2 жыл бұрын
Aren't they using thermite for rails?
@BobbyOfEarth
2 жыл бұрын
@@legaitkl Indeed true. As in all cases, the thermal media is application specific..
@gizmoguyar
2 жыл бұрын
I'm fairly sure they use thermite for rails. This is resistance welding.
@benoit-pierredemaine3824
2 жыл бұрын
This is termite with resistive electricity to initiate reaction. To perform electric resistive welding you would need high pression to shrink the bars together. And pression and timing would be critical. With termite, you leave a nice collar, and you just need to fill the cup to put «about enough »
@desertbob6835
2 жыл бұрын
This Is illegal in the US unless it's A-106, and even then, thetd are restricted usages.
@fartknocker94ioneupyou74
Жыл бұрын
Because YOU can't trust your people
@techscrew2
2 жыл бұрын
He be doing that all day long on a job that size. I’ve never seen this before, on our jobs in uk we over lap and tie. It does look like a strong way of doing it. Does that machine work with horizontal bars too?
@nathan7627
2 жыл бұрын
ya thats how its done in the states too, anywhere from i think 8-24 inch overlay depending on the rebar.
@ispartacus1337
2 жыл бұрын
I dont see why it wouldn't work horizontally. I dont know shit about rebar though, is there a reason you think it wouldn't be as effective on horizontal bars?
@ispartacus1337
2 жыл бұрын
@@nathan7627 seems like that would be stronger. With the way it's done in the video such a small portion of the bar is welded together (only the tips) so it seems like it's only as strong as whatever that shit was he used to weld them together.
@rottenspec
2 жыл бұрын
@@ispartacus1337 definitely stronger, its literally welded and that "shit" is flux
@nathan7627
2 жыл бұрын
@@ispartacus1337 ya i agree
@Wynot1939
2 жыл бұрын
😲 sorprendido deberia trabajar de soldador y no estar desconstruyendo estructuras para casas y peor aun si es un edificio. Las normas y reglas de construcion prohiven tajantemente la soldadura de. Fierro Corrugado ASTM A615-GRADO 60 conocido como fierro corrugado . Tecnicamente en todo el mundo es inaceptable por 2 razones. 1. Puede que se origine uniones fragiles debido principalmente a la composition quimica del fierro . 2. Cuando esta soldado una estructura de fierro y debido a la presion del concreto esta se terminar por romper y si sucede un terremoto ni hablar.
@joseantoniobm41
2 жыл бұрын
China no respeta ninguna ley no norma
@eduardovegagonzalez1066
2 жыл бұрын
Toda la razón 👏
@miguelangelcorreah22
2 жыл бұрын
China creo el coromavirus, les vale verga las leyes
@miguellafieraperez6846
2 жыл бұрын
Por una mala construcción es que hay tantos derrumbes cuando hay terremotos aquí en la República Dominicana soy barillero o amador de fierro como dicen muchos de ustedes aquí se empata
@asdruvalmartirez6601
2 жыл бұрын
EXCELENTE INGENIERÍA CIVIL, MEJOR QUE USAR ELECTRODO Y PLANTA
@enlacdmx4379
2 жыл бұрын
Las propiedades del acero de refuerzo se pierden en el punto de unión. No bueno.
@pelukabassman7453
2 жыл бұрын
ES UNA LOCURA SOLDAR HIERRO°
@abhishekg4138
2 жыл бұрын
When he places the top rebar there's hardly any gap, and then he's putting in that flux and starts the process. I would call it fusion of the bars rather than a weld as both bars completely melt at the join and become one piece. He's also pressing down the top rebar almost an inch or more, which ultimately creates a blob at the point of join, which means more steel and strength. I am sure that flux material is good enough to avoiding oxidation and avoid any air trap or bubble and maybe enhance the material further. Though it's repetitive job and boring for the worker, so are most other labour jobs. It looks this join should outlive the rebar itself. I wonder if the joins are staggered instead of being in same position horizontally, would make the for a stronger structure when done.
@pabloferreira3306
2 жыл бұрын
Equipamento de proteção individual nenhum, o patrão nem ai para os funcionários só pensando no lucro. Quando o funcionário começar a falta para ir ao médico com problemas de saúde, é demissão na certa.
@mariosanchezperez2170
2 жыл бұрын
Excelente herramienta, lastima que la altura del empalme no wea el adecuado. Debe de ser alternado y con diferencia de alturas. Saludos
@edd.lombardo
2 жыл бұрын
If you don't know better, don't say anything
@netzahualcoyotlbriffault6987
2 жыл бұрын
Muy bien
@darlingedeon1599
2 жыл бұрын
Mario Sanchez Perez Lo que tu dices es verdad, Saludo desde Haïti
@davidcondori4375
2 жыл бұрын
Los fierros no se sueldan. Por que se cristaliza y pierde la dureza y su flexibilidad
@javiersotoecheverria8291
2 жыл бұрын
@@davidcondori4375 tienes razon eso se traslapa y amarra al menos con 40 ctm de traslape
@truthbetold2914
2 жыл бұрын
Love those "safety" sneakers he has on
@jerroldkazynski5480
2 жыл бұрын
Safety sleeves would be a plus!
@vdubbin64
2 жыл бұрын
This is why Dubai and Chinese construction fail within years.
@mervjb809
2 жыл бұрын
Why do all the safety nerds have to comment on these types of videos? Just shutup and watch someone being productive, as opposed to being destructive!! Good Lord!!
@reallifeengineer7214
2 жыл бұрын
There is nothing being worked on or moved that, if dropped, could crush his feet. Those short length steel beams he’s welding? Worst case those might give his feet bruises.
@bradmadeira6807
2 жыл бұрын
@@reallifeengineer7214 but that molten STEEL will do HELLA damage to those bunions
@raquelcastrejon1022
Жыл бұрын
Esta todo muy bien, solo un detallito por precaución… No sería mas seguro las uniones en diferentes niveles?
@stevenbreeden3261
Жыл бұрын
Now that's Kool ass hell nice way to do it just time consuming but look at how you can fix one that's way to short I like it that makes it so much easier for rebar layers so kool
@yamaha15737
2 жыл бұрын
Waste of time. Tie the rods way fast and stronger tying them. People that aren’t iron workers don’t know that the slag off the top of a molten pot of iron. It’s junk iron. If welded together the iron above below just cracks and falls apart. Chicago local 1.. 1271835
@mr.goldfarmer4883
2 жыл бұрын
Exactly. There a reason why this isnt common practice. This is probably why chinese buildings have higher rates of failure than most other developed countries in the world.
@HisHolinessMadarchode
2 жыл бұрын
Don't mater all the metal there is made from rice paper
@jaimehanfig9618
2 жыл бұрын
Error: el acero corrugado no es soldable...tiene que ser traslapado...operario despedido y el residente por permitirlo
@Ma_X64
2 жыл бұрын
It's a fckn myth.
@jaimeleiva6302
2 жыл бұрын
También existe el electrosoldable. Eso si, pongo mucho en duda esa técnica para continuar con las barras, en vez de hacer el traslape correspondiente.
@niltoncesar9329
2 жыл бұрын
Gambiarra né,pegando pedaços e emendando,eu dei dinheiro pra comprar a barra de 12 metros,se vira agora,cada uma custa R$237,00 kkkkkkkk
@erdsvalenciasibulo1793
Жыл бұрын
Welding the joint of the bar instead of fastening with galvanized wire IS NOT ADVISABLE. If shake would happen, friction happens in two joints of the bar that surely will split up its welded joints of the bar. Better and more safety to fasten it with galvanized wire.
@marcoguzman737
2 жыл бұрын
Se supone que cuando se hacen las cadenas para edificar no se debe soldar ya que cua do están con concreto y hay un sismo se quiebran, por lo tanto siempre se unen con alambre ejerce menos presión aun movimiento
@enlacdmx4379
2 жыл бұрын
👍 sí, se unen con alambre y debe haber traslape entre los aceros de refuerzo de unas treinta veces o algo más del diametro del acero utilizado.
@paulao12071976
2 жыл бұрын
Debe ser otro acero, en occidente el fierro de construcción no es soldable
@capo1163
2 жыл бұрын
En Mendoza Argentina hacés eso y te tiran abajo la obra😂😂😂😂😂😂
@traex8325
2 жыл бұрын
Stop bashing the worker, he's just doing his job. For all we know it could've been the engineer's idea.
@patriciopeys4864
Жыл бұрын
Ahí está el problema de por qué se les caen los edificios a estos sr,el fierro no se une uno con otro con calor,el traslape es lo correcto ,en esa unión el movimiento telúrico lo quiebra....
@eduardobraconi1736
Жыл бұрын
Eso mismo es lo que tengo entendido, no se sueldan porque el metal pierde flexibilidad en ese punto de union.
@Raul-ne4uh
2 жыл бұрын
Quizás solo este haciendo esa soldadura para conectar exclusivamente a futuro el aterrizaje a tierra del edificio o pararayos ya que los códigos civiles en ese caso si permiten la soldadura Saludos
@javierduran9022
2 жыл бұрын
La toma de tierra es una estaca de cobre,nunca de hierro.
@Prospero625
2 жыл бұрын
When metal got heated it becomes weaker. On this video they've been joined by welding together. I don't know the impact of this especially the joints are at the same level of join in the building. If they are done of different location then maybe it's acceptable. There is a possibility that the joint can snap because it's heated.
@saidmatola8015
2 жыл бұрын
Provide alternative
@Prospero625
2 жыл бұрын
@@saidmatola8015 engineers would determine that. I don’t think building department would allow that unless they upgrade the size of rebar or they can prove that the strength is adequate.
@jimwestbrook4068
2 жыл бұрын
Absolutely. And that will be the first spot for corrosion.
@Prospero625
2 жыл бұрын
@@jimwestbrook4068 you’re right. And if they corrodes that will be the cause of spalling.
@dextar44
2 жыл бұрын
I've been working with concrete reinforcing for 6 years and this is the first time I see this.
@edelpalos1225
Жыл бұрын
Pinches chinitos son la Mera vena saludos desde mexico 🇲🇽
@glenchatters41
2 жыл бұрын
Hard hat √ Safety glasses ✓ Hearing protection ✓ Gloves ✓ Tennis shoes ✓
@Chuckcia
2 жыл бұрын
Why welding rebar is usually forbidden? I guess because welding tempers the rods and a 60000psi rebar changes back to a 40000psi low strength rebar. Am I right?
@JM-yx1lm
2 жыл бұрын
I don't think you're right. Heat is heat no matter if from a welder or this bonding heat. I think the only reason they do it like this is because carrying a welder with leads everywhere is not practical.
@christopherwhippy3181
2 жыл бұрын
Dunno bout your figures but you are correct, it's the same reason why you don't heat reo to bend it.
@robertkington2084
2 жыл бұрын
It's not forbidden. It's not practical. Run the bars next to each other. Usually 30 time the diameter of the bar is your lap splice. But the verys depending on what the engineer has for the given lap splics schedule. Some rebar can be welded and some cant. Never done in the USA Any rebar that is welded is a a706 bar. Here we do lap splices or sometime on big bar when there is not room for a lap splice we will use a mechanical coupler.
@alnov91
2 жыл бұрын
This process is excellent, however annealing is ideal? He is removing insulator to quickly.
@lsimpson6223
2 жыл бұрын
It can't help but change the metallurgy. Heating in uncontrolled environment, amount of insulator, length left on, wind cool quicker, ambient temperature. All have an affect on the bonding joint. Plus the fact that all joints are same height. I would specify alternating heights by 1 ft left to right and front to back. But, that's just my opinion
@thebeardedchefph4980
2 жыл бұрын
behind the great skyscrapers are these tough dudes. respect 👌
@kamchibekdzheenkulov6147
2 жыл бұрын
Варить в разбешку...
@amcvichomes8198
2 жыл бұрын
This is called Mechanical Connection as well. However, reinforcement forging is much better, reliable, and durable than this way of connection
@boujediennenajim1965
2 жыл бұрын
Lots of respect for this worker .
@rodds1909
2 жыл бұрын
Sin equipos de protección personal, salvo un casco y unos guantes. A esta gente de ese país le vale la seguridad de sus trabajadores. Obvio, siendo que hay millonrs detrás de un cargo... por eso pueden ser la fábrica del mundo. Pero si respetaran los derechos humanos otra sería la historia. LOS GOBIERNOS DEL MUNDO YA NO DEBERÍAN COMPRARLES NADA.
@Michael-iu1gv
2 жыл бұрын
No digas estupideces gracias a esta gente están viendo estos vídeos en tu estupida computadora o celular , la mitad de la tecnología en tu casa es gracias a Asiáticos , ya no compren nada dice el imbecil este 😂🤦🏻♂️
@Brandolino94
2 жыл бұрын
Jaja decime que sos kirchnerista sin decirme que lo sos....
@chuckroast5735
2 жыл бұрын
I'd like to take that welded section and put it under tension to see where it fails. IF DONE CORRECTLY I doubt it would fail at the joint.
@antonkw3745
2 жыл бұрын
berapa tahun selesai nya?
@elcormoran1
2 жыл бұрын
as Long is not anglo made construction it won,t fail
@amryms8256
2 жыл бұрын
reminded me to final destination
@petergabriel99
2 жыл бұрын
En México, éso está prohibido....un empalme así siempre es un riesgo.
@user-tj6dt4sz4f
2 жыл бұрын
Даже СКА в Европе вяжут арматуру с перехлестом а тут Нака.
@svoboda21veka
2 жыл бұрын
🤣🤣🤣
@alexandrgansky156
2 жыл бұрын
А тут ванная сварка
@user-ri7ph9cd8p
2 жыл бұрын
好
@pippipster6767
2 жыл бұрын
Imagine the sheer boredom of doing that all day long
@bobbrereton4785
2 жыл бұрын
How about typing off rebar mats all day, stooped over and treading on rebar all day?
@russe19642
2 жыл бұрын
That's twice this week I've seen this method
@benchevia3580
2 жыл бұрын
The strength of joining the steel bars doesn't assure tight bonding of both. It would fail in pull out test. The material melted to create a coupler but the steel bars should also melted to have simultaneous bonding with the coupler. The method is not safe.
@benoit-pierredemaine3824
2 жыл бұрын
Thermite is used to join train tracks and does better join than the bar itself.
@Aatell764
2 жыл бұрын
I'm surprised I've never seen this been done before. When I was a greenhorn and all I did was tie rebar, they'd have me just tie it. This seems like a lot better idea.
@bigjumbo9479
2 жыл бұрын
No tying is better the old way is best
@Wyt0001
2 жыл бұрын
This had me rolling 🤣 fk ya mate golden
@johnjacobjingle8302
2 жыл бұрын
There is a reason why you dont do it.. and a reason why chinese building collapse on the regular..
@earlibee
2 жыл бұрын
tying rebar isn't as strong as steel without ties
@Aatell764
2 жыл бұрын
@@earlibee typing rebar with ties is as strong as tying rebar with ties?
@vanesoganyan8185
2 жыл бұрын
Было же сказано: - С нахлестом 1000 и шагом 100 - Чё вы мне хуйни тут какой-то наварили???
@user-ts6nr2vu3x
2 жыл бұрын
ну 1000 не 1000 а 10 диаметров вроде такой нахлёст всегда требовали хотя я уже давно отошёл от этого новые технологии
@user-mk1hr3ku3e
2 жыл бұрын
@@user-ts6nr2vu3x я предпочитаю старое чем это новое
@josehuezo6317
2 жыл бұрын
@@user-ts6nr2vu3x p
@VANO_Minsk
2 жыл бұрын
Мужики, чисто для общего развития глубже поясните. Т.е. хлыст не торцами, а с нахлестом одного на другой правильно? Мало ли контролировать стройку надо будет, чтоб знать где докопаться)
@user-xx7dm1et1b
2 жыл бұрын
@@VANO_Minsk Сварка для арматуры - это зло. Снижается прочность на разрыв. Только вязка. В интернете есть таблицы величины перехлестов арматуры. Зависит от диаметра арматуры, марки бетона, расположения конструкции... С этим лучше не шутить. А то будет беда...
@lucygabato7546
2 жыл бұрын
Ang galing talaga 👍 dina kelangan magwelding para madugtungan ang steel bars..
@jakelylehemlock
Жыл бұрын
You need to overlap bars atleast 2 feet for a proper splice. Welding should never be done as for structural integrity.
@luismj.2317
2 жыл бұрын
Excelente unión. Más seguro que un empalme. Bendiciones.
@humbertoirrutia2361
2 жыл бұрын
Si excelente unión, pero son muy cortas, y las uniones, eso no es bueno para los temblores, lógico como ellos no son los que van a vivir ahi.
@cristhoper8349
2 жыл бұрын
Jajajaja me cagao
@gustavogocer
2 жыл бұрын
@@humbertoirrutia2361 tienes pruebas de que en un laboratorio esto no logre soportar una prueba a tensión? Sería interesante
@enlacdmx4379
2 жыл бұрын
@@gustavogocer sobre tu pregunta, los còdigos de construcción indican traslapes de treinta veces (y más) del diametro del acero. Claro, varían de país en país y condiciones locales. El acero pierde su temple, súmale que esa es la segunda uniòn a esa altura.
@user-xb9ch4mn6s
2 жыл бұрын
Работник легко справляется, главное чтоб хорошо оплачиваемая была.
@user-fb7of3fs7e
2 жыл бұрын
За такое время с помощью проволоки обычный арматурщик сделает в 10 раз больше. И это будет намного эффективнее
@user-is3tn9mj4v
2 жыл бұрын
@@user-fb7of3fs7e что будет эффективнее? Больше навяжет или прочность конструкции? Оба способа имеют свои плюсы и минусы. Для особопрочных каркасов нужна сварка и сварщики нерукожопы.
@juanfranciscovelasco816
Жыл бұрын
Técnica japonesa, ahorran fierro, pero los edificios quedan demasiado rígidos y con un terremoto fuerte los edificios se quiebran irremediablemente. Nada como el espárrago pasado 10-15 cm
@Nirotceh1
2 жыл бұрын
If this is in China they're known for cutting corners when it comes to making buildings.
@juanjoseavilabardales7968
2 жыл бұрын
muy, muy , muy , buena la soldadura de ingeniería .
@enlacdmx4379
2 жыл бұрын
El acero pierde temple, no es bueno.
@gracielasanchez2845
2 жыл бұрын
!!!que!!!! Este invento, para evitar realizar traslapos de 50cms que es lo mínimo que exige la norma y así ahorrar en el refuerzo? Nada, eso no es lo correcto.
@fidellandavazquez8342
2 жыл бұрын
Exacto , este trabajo no está bien realizado, nunca se debe soldar una varilla, pues queda debilitado el acero, lo más recomendable es lo que has comentado, debe de dejarse un traslape mínimo de 50 cms.!!👍🏻😎
@jorgelora1203
2 жыл бұрын
Opino q si esto esta aprobado por los ingenieros esta buen y así no hacer ka unión de 50 cm de traslados. Eso pienso yo. Ya q no creo q en una obra como la q se ve se le ocurra a un cabillero hacerlo porque así lo a decidido
@jorgelora1203
2 жыл бұрын
Además vean la cabilla q esta uniendo es solo de un metro.
@victorfelixgallegoscastro9926
2 жыл бұрын
@@fidellandavazquez8342 tengo entendido que se prolonga con con fierros en ese "S" y se amarra con alambre, ese acero no se debe soldar pues la soldadura le elimina su temple original de resistencia
@fidellandavazquez8342
2 жыл бұрын
@@victorfelixgallegoscastro9926 es correcto amigo. Saludos!!👍🏻
@jamesna120
Жыл бұрын
God bless the hard working men all over the world
@oscarjaviertarazonacadena1747
2 жыл бұрын
Excelente modo para soldar las varillas de la obra en construcción Ahorra tiempo y esfuerzo humano
@user-tu1jr3ct9c
2 жыл бұрын
Арматура во всех бетонных конструкциях только ВЯЖЕТСЯ , любая сварка отпускает металл , лишая его расчетной прочности .
@denned132
2 жыл бұрын
Ты самый умный, а он дурилка картонный не зает что делает
@alexshonsu5463
2 жыл бұрын
@@denned132 у нас в СНиПе написано так. А его не дураки писали.
@javierjaime2790
2 жыл бұрын
Que chingoneria, excelente trabajo!!!!
@enlacdmx4379
2 жыл бұрын
Con este método de unión, la columna tendrá un punto débil a esa altura. Lo adecuado es sobreponer otro acero unas 30x el diámetro de ese acero, asegurarlo con alambre.
@alfredomarquez9777
2 жыл бұрын
@@enlacdmx4379 45x, cuando menos!
@user-px3md9wm3o
2 жыл бұрын
А это надёжно? Может надо делать нахлёст арматуры сантимов на 5 - 10
@alexandrgansky156
2 жыл бұрын
Нет. Это самый надёжный, хотя и самый дорогой вид сварки - ванная
@dimashkamaleddinov9616
2 жыл бұрын
@@alexandrgansky156 Один толковый хоть здесь👍👍👍
@deanklear4940
Жыл бұрын
If the weld holds better than an overlap rod-buster wire tie, your saving enough $$$ to pay his salary and the results are 10X stronger before being encased in concrete. The inventor of the welding machine made a Fortune ! Mucho denero' !
@WSaigon
2 жыл бұрын
Термитной сваркой и рельсы варят, делая бесстыковое полотно для скоростных ж/д магистралей.
@nycteascandiacus8349
2 жыл бұрын
Это не термитная сварка, это электросварка под флюсом.
@user-fs5mx2cf3q
2 жыл бұрын
Классная вещь ! и не надо за вечно пьяным сварщиком бегать ,который орет да кто вы без меня Я тут главный ,,
@user-om2xq8zg2z
2 жыл бұрын
Ты за этим чуваком бегать будешь,это медленный процесс,представь пака всё выставить, и т.д.....
@user-iz6zt9pj2p
2 жыл бұрын
Сварщик прав! Он один выполняет сварочную работу а вы толпой стоите над душёй! А бабло получать поровну! Он один а вас человек 5 - 10 !
@user-yj5mm2en1s
Жыл бұрын
เยี่ยมมาก
@elchinodelacumbia
2 жыл бұрын
Algo que jamás se verá en PERU...
@user-jt7om3uy4u
2 жыл бұрын
Не приведи ни кому находиться в этом доме, а не то, чтобы жить в нём. Грубейшее нарушение строительных норм и правил .Нагревание арматуры строго запрещено, только холодная резка, рубка, вязка.
@user-Dima599
2 жыл бұрын
Чото я посмотрел и у меня в носу этот запах появился
@user-gj5iy8ss3q
Жыл бұрын
Самовнушение
@user-Dima599
Жыл бұрын
@@user-gj5iy8ss3q Ну да . 🤝
@MegaMozart13
2 жыл бұрын
Арматуру нельзя сваривать по определению. В районе сварки металл арматуры потерял свою конструкционную прочность. СНиП не обманешь. Этот обман может потом вылезти боком.
@user-mg5wt7xe4l
2 жыл бұрын
Вы ошибаетесь, таки её варят, и для этого есть так нормы и правила
@Sergey_748
2 жыл бұрын
У китайцев свой СНиП
@MegaMozart13
2 жыл бұрын
@@user-mg5wt7xe4l У китайцев?
@MegaMozart13
2 жыл бұрын
@@user-mg5wt7xe4l я прошу ссылку на данный документ! Жду!
@MegaMozart13
2 жыл бұрын
@@user-mg5wt7xe4l я такие эксперименты проводил лично. Физику не обманешь.
@richardsalinetrojr1957
2 жыл бұрын
Does that not weaken the integrity of the steel by heating it like that then letting it air cool creating what I would think is a soft spot where the connection is?
@Country_Life_Japan
2 жыл бұрын
Don’t think it makes that much of a difference 🤔 because it not a big piece! It’s just a rod! But I could be wrong 😑 lol 😂
@joerosas2876
Жыл бұрын
Muy bien Pero cuando termine ya los carros empezaran a volar😁
@user-jx2tz7zy2d
2 жыл бұрын
Хитро и практично! А главное просто и надёжно
@alexshonsu5463
2 жыл бұрын
Это лажа, варить нельзя, тем более в стык.
@New-0
2 жыл бұрын
Función excelente inventó, aquí siguen con alambres
@PompyDoBetonu
2 жыл бұрын
Muy mala técnica. Es prohibido alargar así las esperas o armadura
@Mike-jd5xu
2 жыл бұрын
Pas mal , plus pratique et plus rapide qu'avec un poste à souder.
@user-ud3in7qp8l
2 жыл бұрын
2022,01,29(6)植筋工,或許也可以改直接鋼筋用有鑼紋鑼絲用鎖的方式植筋
@jhonm.riosgiron5404
2 жыл бұрын
Gracias por compartir, no conocía está técnica
@user-ez7mx7tq5u
2 жыл бұрын
Это ещё что они придумали блин хот есть в мире человек что бы в перед их что то придумал а ? Все китайцы сначала а потом другии
@007dhen
2 жыл бұрын
That method was gas welding to skip the lapping method...but it was a rare method now....the new method today is called Rebar Coupler...
@hareramanama
2 жыл бұрын
Спасибо за просвещение!
@nicolaspinovallejos8257
2 жыл бұрын
Ese era el segundo. Ya tenía uno enfriando y rápidamente fue por el tercero😎💯
@cesarluisaltamiranda9944
2 жыл бұрын
MUY bueno ese trabajo como se llama lo que inserta con la vandeja ? Gracias
Пікірлер: 2,5 М.