The assembly was fun to do. I like how easy but genius these machines work and I learned a lot. Hope the video helps you!
@sw-ed5sx
4 жыл бұрын
You make it look easy. Great job!
@bikedogtor1663
4 жыл бұрын
Thank you :-)
@tobysmith8032
2 жыл бұрын
Top tip... Remove the ears from the circlips, they tend to vibrate and either break off or the circlip works its way out! 👍
@bikedogtor1663
2 жыл бұрын
Thank you
@ATLAS01COPCO
4 жыл бұрын
Great cleaning job
@tysauce1986
2 жыл бұрын
Do you know what the factory settings are for the H and L carb screws?
@bikedogtor1663
2 жыл бұрын
No sorry
@dalechalkey3729
4 жыл бұрын
are the bearings on the crank shaft the same size? on my ts420, it looks like one of the bears is a 15mmx35mm by 11mm. the dealer sold me two of the same bear sizes but i think my unit is older and uses two different sizes.
@bikedogtor1663
4 жыл бұрын
They aren't :-/ I ordered two of the same size and stopped bc one didn't fit.
@tjs.mw.
Жыл бұрын
The one I did had 2 different sizes
@williamcawthorpe8910
15 күн бұрын
After 2013 the bearings are 2 different sizes
@husky-cc6xq
Жыл бұрын
Servus Bikedoctor, why you document in english? I got a quotation from a Stihl dealer, but the price for zylinder is very, very high and am honast, the fixing of exhaust is a missconstrution. Do you know a a good dealer for Stihl parts? Thank you Toni
@bikedogtor1663
Жыл бұрын
Hi, I bought only after market parts online
@jorgetrigueros1820
3 жыл бұрын
Does crankshaft for 420 works on 480
@bikedogtor1663
3 жыл бұрын
I don't know
@jorgetrigueros1820
3 жыл бұрын
Ok thanks for answering my question
@jorgetrigueros1820
3 жыл бұрын
Do you know where I can get parts after market
@bikedogtor1663
3 жыл бұрын
I don't want to name any bc of advertisements
@Jose50008
3 жыл бұрын
Great job is not easy.
@bikedogtor1663
3 жыл бұрын
Thank you
@RicardoFlores-tq4wr
11 ай бұрын
What is the company called and what is that piece called plz 2:31
@bikedogtor1663
11 ай бұрын
The ice spray?
@tjs.mw.
Жыл бұрын
Alittle tricky but I did it
@bikedogtor1663
Жыл бұрын
Yess
@JosueA-j3y
8 ай бұрын
Exelente colega muy buen trabajo
@johnkosheluk1041
Жыл бұрын
You don't do a psi and vac test on the crankcase what do you think will happen if you have a air leak especially on that aftermarket piston and cylinder
@bikedogtor1663
Жыл бұрын
Next time I do that
@phyllismacevicius8821
2 жыл бұрын
Thank you for sharing the TS 420 rebuild and assembly. I am doing this rebuild currently and your video is very helpful.
@bikedogtor1663
2 жыл бұрын
Thank you
@funkhybrid
3 жыл бұрын
Is there a reason why you don't use any lubricant or grease when you're re-assembling the main shaft and bearings? Seems like it would slide on a little easier. Enjoy your vids
@bikedogtor1663
3 жыл бұрын
I never use lubricant on the outside of bearings bc if it goes bad the outer ring can slip in the housing and destroy it. You definitely do not want that to happen.
@pakolorente7423
3 жыл бұрын
Nice music - rebuild Aprilia bring me here. How many cc is in this engine saw?
@bikedogtor1663
3 жыл бұрын
Thank you for your comment. I don't know to be honest.
@CarlosGarcia-xs6ig
Жыл бұрын
Buen bidio
@NEW-HORIZONS
2 жыл бұрын
Where can I buy accessories (cylinder and carburetor)
Пікірлер: 42