We have about 15 fs94 trimmers, all but a couple old style primer. Of the 15 only maybe SIX will always run as they should. Rest have what seems to be fuel issues, will idle but will not rev up they just bog. a FEW of these will rev if you let them idle till they're just about to flood. I have worked on every aspect of the fuel system per stihl service bulletin, mostly w/o luck. I have thoroughly cleaned the carbs, the tank vent (the tube thru the air filter housing is too darn small clogs up). New style fuel filters help sometimes. I adjust the main jets way out, sometimes this cures them but only for a while then bogging returns. Dealer had one while it was still in warranty, got it back "OK" and it quickly started bogging again. Seems like a fuel priming problem. Sometimes the primer bulb won't pump, seems like the check valves in it are nfg. I kinda suspect the tank vent assembly too, I understand there are new style vents. We pull the muffler screens when brand new. We have had numerous ones where a clutch won't lock up, I used to replace them ,now I clean them in the bushings that the shoes pivot on and reassemble with a tiny bit of silicone grease. I stock clutches and the starter dog assy (engine side little black flappers) as they fail by just wearing down. I service fs94's for other landscapers and this bogging issue is commonplace and very frustrating because they leave my hands running great but come back soon bogging again. Noticed it on the web as well. Boss says WE WON'T BUY ANYMORE Thanks for listening.
@jarrod1687
5 ай бұрын
Try husqvarna 525lst
@bhunt919
9 ай бұрын
Love the 94s. All I want to use for weedeaters anymore. Hate they went up in price recently. I've had some problems with the clutch on mine but it's from me moving the shield back to run the string longer. Haven't really had any problems with the pruners though. We've had probably 50 of them. The first thing you do is take the spark arrestor off the muffler. It tends to clog and makes it run bad.
@CNKCLAN2
6 ай бұрын
First thing is remove the spark arrestor screen and keep them maintained properly. Almost every problem that people discuss comes from this. A dealer can't suggest removing the screen for obvious reasons, but this is crucial unless you want to be dealing with that constantly. Other than that, we've had no issues from our 94s and we run them commercially so they have many hours on them. Just fyi for future persons who see this.
@bhunt919
6 ай бұрын
@CNKCLAN2 yea thats the first thing I do with them. I learned that on the 94 pruners. The spark arrestor screen will get completely clogged after like a month of good use.
@Lakecenterlawncare
9 ай бұрын
I had 2 94's. Both had carb issues and would smoke and lose power when tipped sideways. Switched to Echo 2620's and love the power and reliability. However i love the weight of the Stihl and the grip and throttle, but Echo is a better trimmer. Chainsaws however, Stihl for life! Best in the biz.
@ceejay6882
Жыл бұрын
I've seen a common failure in the recoils but different to what you describe. The carrier that engages the starter pawls (even new pawls) skips and chatters without turning the engine. I can't see the point of failure because it's hidden and my best guess is the engagement carrier has too much play from wear. Has anyone had this happen?
@kimreid-v9h
Күн бұрын
How do to change primer bulb on Stihl HL 94.
@luigitorchia8866
2 ай бұрын
Thanks for the great vidio. My machine still stalls after I rebuild the carberator. Whats wrong wit my machine. Thanks.
@bragdytwtlolthetrefforestb6772
8 ай бұрын
Hi Wally! Loved the video. Great insight. I bought a second hand HL95, a very similar unit. It has a problem! The blades wouldn’t move when I got it. So, I replaced the piston rods in the gear box, which were clearly gone (the bearing cylinders were all over the inside of the gear box). Other than that, the gear box looked in good shape. After replacement, the blades still wouldn’t move. So I loosened the blade nuts & screws (which I know you said not to loosen, but just temporarily!). Then after detaching the cutter unit from the main shaft, I could turn the drive rod receptor on the hedge unit and the blades move ok. However, when I reconnect the main shaft, I initially get a small movement in the blades, then they stop moving. At the same time I get a bit of rattling noise from the shaft. I’m wondering if that it an indication the bearings on the base (fan unit) are also gone. Would love to hear your thoughts? Do you have a video at all of a fan unit - bearings replacement? Hello from Wales, UK!
@bragdytwtlolthetrefforestb6772
8 ай бұрын
I’ve just spotted there is a missing needle bearing!!! The cogs and pistons must be popping out of alighnment, hence why it starts to move. I guess manually working the rod receptor isn’t causing enough movement to pop it out.
@protoxbl4548
5 ай бұрын
all trimmers need spark screens cleaned frequently or removed. Located on exhaust of the machine
@guycocquyt345
3 ай бұрын
Great video, one problem I have on a fairly new machine is the articulated head won't move beyond 90°. The spring loaded sleeve and pin seem to be working fine, what do you recommend?
@mmarciniak
2 ай бұрын
Nothing.
@fintan2830
7 ай бұрын
Is the KM94R powerful enough to run a brush cutter blade? Great video, thanks
@wallysworkin823
7 ай бұрын
Yes it is.
@richieomalley8303
3 ай бұрын
Hi Wally i have a km 94 combi its cutting out a lot while runnig idle. any ideas
@mmarciniak
2 ай бұрын
It’s a problem with the engine.
@npet6842
Жыл бұрын
Excellent review . I'm buying !
@Withjesusforever777
10 ай бұрын
How do you like it so far
@tomatherton9959
Жыл бұрын
Hey Wally could you do a review on the atom edgers? I love the atom edgers but always have problems with mine hahaha
@wallysworkin823
Жыл бұрын
I have never seen one in our shop. I will if I see one though.
@jobehayes8444
4 ай бұрын
I have a newer stihl hl 94 k and they suck also use them at work ....and there's constant engine over reving??
@F56tho
3 ай бұрын
Is there any extended good trimmers that you would recommend? Thanks!
@mmarciniak
2 ай бұрын
Back off on the throttle.
@user-ir8cm1gs4z
Жыл бұрын
Are you sure you can't adjust these blades? Mine have too much play and the bolts are as tight as they can be. Do I have to buy a new header in this situation? The trimmer has done a lot of cutting.
@mmarciniak
2 ай бұрын
Cutter bar is worn out.
@kevinorr6880
Жыл бұрын
Have you done a video on a trimmer that will idle but dies when gas is applied?
@wallysworkin823
Жыл бұрын
I'm working on a video about diagnosing equipment.
@mmarciniak
2 ай бұрын
Bad fuel Carb dirty Fuel pump diaphragm dry/hardening Crankcase leak
@ackack1
Ай бұрын
@@mmarciniak I've eliminated your 1st 3 potential problems. But unit will start & run fine for about a minute then bog at full throttle & soon thereafter it will simply quit. Thus, I suspect that the crankcase somewhere expands & develops a leak after it gets hot. Where on the crankcase do you most often see a leak?
@JR-id7lf
10 ай бұрын
What kind of fuel do you recommend on the hl94 unit?
@wallysworkin823
10 ай бұрын
I always recommend ethanol free if you have it in your area. Otherwise 91 pump is fine just don’t let it sin in the unit for long periods.
@lazylearner967
Жыл бұрын
Do you like this KM 94 more than the KM 91?
@nikgotro770
Жыл бұрын
I’m wondering this as well….
@jeffdenney4148
Жыл бұрын
Where can I pick up a bare mine is broken
@mmarciniak
2 ай бұрын
Bear are hibernating at this time.
@24space310
Жыл бұрын
i knew the plastic would rot at some point or fall apart.
@cbnx82703
8 ай бұрын
Integrated Purge Bulb not a Primer , Im sure you know that…!
@cbnx82703
11 ай бұрын
That bearing fails quite often, Ive seen the housing come in burnt from seizing and getting so hot they were smoking… $67 with the bearing , they make noise when they go bad
@wallysworkin823
11 ай бұрын
And the machine will vibrate really bad when the bearing fails.
Пікірлер: 42