The importance of a small multimeter is so vital. MIGHTY ACTION GOD BLESS NA SELFISH WITH THE KNOWLEDGE. BLESS UP.
@MightyAction
Ай бұрын
RESPECT MI G, THANKS FOR THE FEEDBACK
@heartofalion1040
Ай бұрын
When I do big shows I put my racks next my speakers and my speakers wires about 10 feet long 8 pin
@MightyAction
Ай бұрын
THANKS FOR THE INPUT MI BOSS
@elvismakonde5385
Ай бұрын
Nice video bro! Big Up. However from my little amplifier circuits theory, the output signal from the amplifier depends on the input signal which is controlled by the knobs (attenuators) in front of the amplifier. The higher the input signal into the amplifier the higher the amplified signal out of the amplifier. The quality of the input signal (in terms of distortion and noise) and the amplitude level can result in an amplification of the same causing blowing of speakers due to overheating. Therefore I want to concur with @aaronlake although a very high-wattage amplifier can blow a low-wattage speaker even with a low signal level at the input.
@MightyAction
Ай бұрын
Therefore I want to concur with @aaronlake although a very high-wattage amplifier can blow a low-wattage speaker even with a low signal level at the input. THE LAST PART OF YOUR STATEMENT IS MY POINT. HOW EVER THANKS FOR YOUR INPUT, REALLY APPRECIATE IT.
@wadephillips6052
Ай бұрын
Correct ia. That where the limiter in the speaker management comes into play.
@platinumprovocateur412
Ай бұрын
Mighty action yes its corey aka mr platinumprovocateur thank you for clarifying my two questions really appreciate it. So yes my double 18" bass reflex, B&C 8ohms drivers so as i said to my mate we should not play it in the option he said by doing 3 and 3 on each channel. though I did say to him we should do it 1 on each channel and use another amp 1 on each channel and we shall be safe because we use parallel wiring. thanks again king
@MightyAction
Ай бұрын
YOUR WELCOME BRO
@Priceless_ikon6438
Ай бұрын
I been talking about the 4 ohm’s but people been laughing at me like I’m a fool still. But thanks for putting out here sah 💪🏾
@MightyAction
Ай бұрын
ANYTIME.
@heartofalion1040
Ай бұрын
I appreciate the meter because I always thought that the speaker was 8 ohms now I know better thank you JAH Blessed
@MightyAction
Ай бұрын
YOUR WELCOME, GLAD I COULD HELP
@dadalinks
Ай бұрын
Keep up the good work Mono vs. Stereo setup should be your next topic.
@MightyAction
Ай бұрын
Thanks for the idea!
@megaforce1237
Ай бұрын
Good conversation learned something every time I watch your channel thanks for all you do
@MightyAction
Ай бұрын
your welcome
@iwayne637
Ай бұрын
1. Speaker ohms varies with the frequency youre playing through them. 2. Measure the ohms from the end of that long speaker wire Jamaicans use, and you will find you're closer to the 8 ohms, and well well pass it too..
@MightyAction
Ай бұрын
THANKS FOR THE INPUT MY BROTHER, I WILL PUT THAT TO THE TEST NEXT VIDEO
@justyna4276
Ай бұрын
Love the teachings iya
@MightyAction
Ай бұрын
Respect
@platinumprovocateur412
Ай бұрын
am glad I asked the question so am satisfied yes big man this was just very informative you have gone above and beyond Mighty Action bless you from corey aka platinumprovocateur over here in the United Kingdom
@MightyAction
Ай бұрын
Glad to help
@RowanThompson-rg1xw
Ай бұрын
1.5 if u round it off to 1 decimal place is 2 ohms because 5 and up u round up. However good teaching respect
@MightyAction
Ай бұрын
I thought about that too. But just showing the actual numbers
@RHUMBAVDJALPACINO
Ай бұрын
no no no check the battery of the meter. the resistance wont be correct if your meter battery is low.the first reading immediately you attach the meter terminals is 7.5.so kindly replace the meter battery you will get the correct figure .thanks
@ozzytrait4777
29 күн бұрын
Big boss I was in Milan when your video drop I've come back to 🇬🇧 👀 you 📹 there's some things I've learnt that I never knew I was doing wrong before 🙏🏿 up big boss 🇱🇨🇲🇸🇬🇧
@badazz12r
Ай бұрын
Bridge mode just changes the 2 channel amp to a Mono block amp,both sides are being used to power a single output. As action said if you you run it hard 24/7 it will break.
@MightyAction
Ай бұрын
EXACTLY
@robertrobinson464
Ай бұрын
To be honest it is good to learn because from you I learn alot just now respect to you mi general
@MightyAction
Ай бұрын
Respect
@ryanbrandford3780
18 күн бұрын
Very informative. I've done a lot of research and found out these things too. First mi eva really hear a sound man come out and talk bout these things. Keep up the good work. 2 a side with some with some 21's can help build up back the loudness instead of 18's.
@platinumprovocateur412
Ай бұрын
Glad you mentioned about the cabling excellent
@MightyAction
Ай бұрын
Glad it was helpful!
@platinumprovocateur412
Ай бұрын
@dadalinks yes I agree that should be another topic Good call mono v stereo set up 👍🏾
@MightyAction
Ай бұрын
THATS ON MY AGENDA, BUT I WANT THAT TO BE A SPECIAL TOPIC SO I'M WORKING ON THE THINGS FOR THAT
@wadephillips6052
Ай бұрын
I always try to use 4ohm to not run the components at the limit as with 2ohm. I leave 2ohm for emergencies 💪🏾💪🏾
@leroyrichards-ps2ey
14 күн бұрын
So about the ad442 and ohms,, you said the subs are not 8ohms so you would NOT recommend 4per channel and that is a good advice BUT, remember "WIRE RESISTANCE " as you (previously mentioned and tested) most speakers wires are between 50ft-100ft which will automatically bring the ohms from 6.2ohms to 8ohms. Connect a 100feet speaker cable to the speaker and test the ohms from the other end of the cable and Please inbox me with the results
@badazz12r
Ай бұрын
the AD442 can do all six double 18's, each channelwill play 3 woofers at 2.6 ohms. wiring NL4 1+ 1- equal channel 1, 2+ 2- equal channel 2 (same way for channel 3 and 4) this way you will have 2 4 conductor speaker leads. first nl4 to 1st double 18, nl4 jumper from box 1 to box 2 then to box 3. Do this for channel 3/4 also. DO NOT BRIDGE AMP
@platinumprovocateur412
Ай бұрын
Keep up the good work mighty action nice of you to give your time so appreciated
@MightyAction
Ай бұрын
Respect
@badazz12r
Ай бұрын
wiring of components and speaker leads drops the impedence fo all speakers
@platinumprovocateur412
Ай бұрын
I've got it 100% thanks again from corey in United Kingdom - London
@MightyAction
Ай бұрын
YOUR WELCOME
@robertrobinson464
Ай бұрын
That's the same way I run my system 2 a side on my amplifier
@MightyAction
Ай бұрын
Nice 👍
@STATEMENTNYC
Ай бұрын
I have a question how can you test to see which is positive and which is negative on a amplifier if it rubs off or if it's not indicae thank you for the good work. Thank you so much. Very helpful.
@MightyAction
Ай бұрын
not sure what your referring to, but i would look up the manual and look at other amps like it. what amps is this?
@LEOTECHMUSIC
Ай бұрын
Go easy my brother! Let’s clear up something. While it’s not necessarily 8 ohms using your white board 6.2 x 4 speakers is going to be 1.5 which rounded up equals 2 ohms! While it may be shocking to see those 8 ohms speakers actually reading less you have to realize they are other factors at work so in actuality the output of the amplifier isn’t going to be constant when it comes to VOLUME which is what we really work with so while we focus on ohms and watts with speakers what’s really important is the SPL! 👍🏿👌🏿so keep in mind that these numbers that you see with these specs are based on a reference using (2,4 or 8) ohm load. Under test conditions you would have a constant output with constant loads hence the reason for those numbers aka(reference) As you were sir. Don’t knock the 4 a side my friend continue there’s much more to learn 👏👏👌🏿👌🏿👍🏿👍🏿
@platinumprovocateur412
Ай бұрын
yes mighty action I shall stay in that theory
@MightyAction
Ай бұрын
👍🏾
@robertberry4806
Ай бұрын
Yes u real 8ohm boss Me too on my little sound
@Blackunitsound-system
Ай бұрын
Which sound wasi are in Jamaica Denton
@DJMikeLoverSmitty
Ай бұрын
yes 2 per side is the rule for good sound . I play with the I Nuke 12000 and everybody say you sound good
@MightyAction
Ай бұрын
Thanks for sharing mi boss 👍🏾
@leung619
29 күн бұрын
Mighty action, speakers are not resistive loads they are reactive loads, meaning while playing music the ohms load changes with each frequency (impedance rise) more often than not your amplifier would not be seeing let's say 2 ohm if your speakers are wired to 2 ohms, because of impedance rise the amplifier would be playing at a comfortable level. You should do some research on box/impedance rise.
@patrickchung7538
28 күн бұрын
Dont know if its factual, but what i was thought is that with wires considered the amp should see the missing 1.5 ohm. The wires for a 100 ft 12 ga. should drop between 1 to 2 ohms.
@Blackunitsound-system
Ай бұрын
The Jamaica don't know one dam thing about those things till they know how much them a play for
@leroyrichards-ps2ey
14 күн бұрын
What that means bro?
@selectorerwin1don12
26 күн бұрын
arite me general so is it possible that when a technician build or recoil a speaker would u advise to let the technician drop the ohms to around 6. 2ohms cause normally i see technician rewind it at 7.6 or 7.9 ohms .. whats ur thought on that?
@Blackunitsound-system
Ай бұрын
We can damaged the sound speakers to compete
@Blackunitsound-system
Ай бұрын
That's right not with those amplifier
@bheempitamber2882
9 күн бұрын
Gn how do u make your power distro with a transform
@philmckoy9
Ай бұрын
Bro it seems like you are relaying information that's been told to you so I'm not going to hold you to it. The reason you are getting 6.2 or 6.3 ohms is because you are reading the dc resistance when the speaker is connected to the amplifier then the coil puts out a higher value because its now in a AC circuit. In the sound system business tweeters and horns are coupled in series which gives you a better chance of not blowing them in a 4 or 5 way system each section has it's own amplifier so playing highs and horn at 16 ohms and the others at 2,4 or 8 ohms doesn't matter. And you add resistance in series not multiple cause if you had a 4 ohm in series with a 8 ohm multiplying wouldn't work as to how you doing it . Also a little nugget when you put two speakers in series it can only play as loud as one where each speaker will only play to half its potential but will survive more often than parallel.
@Blackunitsound-system
Ай бұрын
Play the 18"like it's 21"
@Blackunitsound-system
Ай бұрын
Four Calum that means they are not playing off of none
@georgeogrady449
Ай бұрын
May be up to 8 ohm
@Blackunitsound-system
Ай бұрын
You have to make them
@mikeyshockwave4352
Ай бұрын
Although manufacturers label their speakers @ 4, 8, and 16 ohm as just a standard, this is why they refer to it as "nominal impedance" But the actual DC resistance is usually lower. There are many factors why this is so, but it is not something you should be overly concerned about because a speaker's load is not static. It changes do to the coil moving and it changes at different frequencies while under load... I suggest you look up impedance rise, more commonly referred to as "Box rise".
@MightyAction
Ай бұрын
THANKS FOR THE FEEDBACK, MOST DEFINITELY WILL LOOK INTO THIS.
@mikeyshockwave4352
Ай бұрын
@@MightyAction 💯
@Blackunitsound-system
Ай бұрын
I don't understand is stereo Bass nighter
@Blackunitsound-system
Ай бұрын
Yeah put the bridge sounds
@Djjahlumps007
Ай бұрын
How would you wire 2 8ohms tweeter to get 8 ohms?
@legomanstar2511
Ай бұрын
You cannot, you can only get 4 (parallel) or 16 ohms (series)
@MightyAction
Ай бұрын
@legomanstar251 IS 100% CORRECT. BUT YOU CAN USE TWO 16 OHMS TWEETERS IN PARALLEL TO GET THE 8 OHMS YOU WAN'T
@heartofalion1040
Ай бұрын
What gauge wire do you use?
@MightyAction
Ай бұрын
USE FOR WHAT?
@heartofalion1040
Ай бұрын
@@MightyAction subs mid bass mid high horns tweeters
@MightyAction
Ай бұрын
CURRENTLY USE 13 GAUGE ON TOPS (HORN, TWEETERS, HIGH MID AND LOW MID). USE 12 GAUGE ON BASE BUT I'M ABOUT TO SWITCH TO 10
@Blackunitsound-system
Ай бұрын
Because those sound is not a normal sound system why they play four Calum
@georgeogrady449
Ай бұрын
2 ohm 3 ohm 4 ohm 8ohm 16 ohm
@georgeogrady449
Ай бұрын
3 ohm on to 8 ohm
@georgeogrady449
Ай бұрын
How get more volume with out peaking it
@philmckoy9
Ай бұрын
If your input signal into the amplifier is too high it will cause it try turning down the signal before it goes into the amp and then turn up the amplifier.
@Blackunitsound-system
Ай бұрын
Uno have some education I don't see it so
@Blackunitsound-system
Ай бұрын
You know say me get it because it is still in your head
Пікірлер: 91