The best ide presentation ever , I really like the calm voice.
@stmicroelectronics
3 жыл бұрын
Glad you liked it!
@kenwallace6493
3 жыл бұрын
Probably the most helpful video for moving up the learning curve for this IDE. Thanks!
@stmicroelectronics
3 жыл бұрын
Awesome, thank you!
@walterhynson2898
3 жыл бұрын
learned more from this video then ever before thanks for getting someone who knows how to teach please make more like this
@random.vlogator
2 жыл бұрын
If you are following this tutorial but run into the build error while using osSemaphoreWait function, you should change it to osSemaphoreAcquire function instead. Then, you will not get "Undefined reference to `osSemaphoreWait'" anymore. FYI - I'm using NUCLEO-L476RG board and CMSIS_V2. The CMSIS_V1 still uses osSemaphoreWait function.
@satyabratasenapati7376
5 ай бұрын
Thank you for the demonstration. 😂😊
@user-nx5ew2pz2b
5 ай бұрын
I am using G071 Board. But here it does not show "interrupt nesting behaviour configuration" Settings in FreeRTOS Config Parameters.
@goodwill7643
3 жыл бұрын
Hello, Would you please continue with these tutorial series? I mean in general STM Tutorials, timers, SPI, Interrupts, etc... Thank you.
@stmicroelectronics
3 жыл бұрын
Yes, we will ! Glad you enjoyed it !
@gerardopalacios4062
4 жыл бұрын
What Happened at 30:51?? Why you suddenly changed it to TIM7? It didn't work either with TIM6 in my board, but WHY!?
@stmicroelectronics
4 жыл бұрын
It is postprocessing issue. Part with timer6 should be removed. I have checked once again with STM32CubeIDE v1.3.0, using Nucleo-G071RB and it is working for Timer6 and with Timer7 ( I have checked it for CMSIS_OS v1 and CMSIS_OS v2). In case of further technical issues with the code, I would suggest you to move to our forum at community.st.com . It will be easier to exchange the information.
@vldgrs
4 жыл бұрын
STM32 is the best! However what is the problem with Thread awareness for debugging? People report on forums they've sorted it out with OpenOCD but I'm struggling to get similar results. Even with the latest IDE v1.3.0 update. Can you show how you do it please?
@imcnx1563
4 жыл бұрын
why did you change the time base generation to tim7?
@stmicroelectronics
4 жыл бұрын
Hello. It is a postprocessing issue.
@MilanKarakas
3 жыл бұрын
There is no "green pin", just grey metallic pins. Unable to set bit: GPIOB->BSRR = GPIO_BSRR_BS11;
@stmicroelectronics
3 жыл бұрын
Hi there, thanks for your question - may we point you towards our community.st.com, where you will find a team of people who can answer you directly ?
@itonjoans354
4 жыл бұрын
I don't have freeRtos in my middleware pull down, can you do a video on how to install it?
@stmicroelectronics
4 жыл бұрын
Hello, may I ask you to post this question to our forum, please (community.st.com) ? If you could provide a bit more information about the issue (board and MCU you are using, version of STM32CubeIDE and version of STM32G0 library) is would help us a lot. Thank you in advance.
@MKDas
2 жыл бұрын
Can't you guys speak little bit loud ? Most of the videos of ST, can't hear clearly even with high volume + speaker. video helped a lot, but your voice is damn low.
Пікірлер: 21