Needed this video 3 months ago for my jon boat after I tried my second pack of alumiweld rods, warping the bottom hull from overheating from the mapp gas and the still leaky crack. We’ll done sir, the guy from Muggy Weld on the phone with me will thank you for this lol
@EngineeringHooksets
2 жыл бұрын
I'm glad it helped you! And yeah I feel that. The first time I repaired a leak I brazed too.
@cowboyup545
Жыл бұрын
Nice Job Young Man.
@ryanskare6670
2 жыл бұрын
Ok. If you are going to say use 5200 (a 3M product) don't show a Loctite product. Also, 3M 5200 is not very flexible once fully cured. I would also recommend checking out another very popular channel where he puts the most common brazing rods to the test. There are 3 brands I would use for this repair over an adhesive patch and one of them can be found a harbor freight.
@EngineeringHooksets
2 жыл бұрын
Yeah Ive used 5200 in the past and I misspoke about this, my bad. I disagree, doesn't matter the brand, if the aluminum hull isn't melting with the braze rod the bond will never be great on a flat surface. I learned that twice the "hard" way.
@michaelsherwin3
4 ай бұрын
Would it be worth using an etching primer?
@alamomarine87
Жыл бұрын
Great job on this repair. Drilling the end of of the cracks creat relief holes. Not sure if you knew this but, round patches are a great patch because corners create stress points. When creating patches in aircraft structure, square patches have a radius or rounded corners. I would recommend installing a few rivets on the inside perimeter to better secure the patch an feom the outside to increase the life. An added piece of aluminum on the outside, known as a doubler would be even stronger. Overall, great job.
@misterbulger
Жыл бұрын
Just tried braising with alumiweld sticks and i cant get the metal hot enough. The boat is just a giant heat sync depiste using two torches together. It looked like the braize took but i filled the boat with water and it still leaks like a seive. I tried to pull the old solder out to try it again but i ended up just ripping a larger hole in the boat. Id try a poropane oxygen torch but that much heat may just blow a biggger hole through it. Ill try this next. Trouble is its on one of the ridges that run the length so itll be hard to get flat.
@EngineeringHooksets
11 ай бұрын
Yikes. Did it end up working out?
@misterbulger
11 ай бұрын
@@EngineeringHooksets i just used that 3M marine sealant. Way easier to work with. I am not skilled with those rods at all.
@beestoe993
4 ай бұрын
Tells everybody, "Dont use a rigid repair, it wont flex and will pop off". Then uses JB weld. 🙃
@EngineeringHooksets
4 ай бұрын
I see your point, but what I was trying to convey is don't rely only on a rigid repair. The main patch is what I did on the inside. The outside JB Weld I added was just to protect that flaking metal from catching on stuff. It was not intended to waterproof
@beestoe993
4 ай бұрын
@@EngineeringHooksets I wasn't being very nice. I'm sure your repair is a good one. I just think brazing on the bottom would be more likely to hold up to abrasion and such. Thanks for taking the time to make your video.
@dking4995
4 ай бұрын
That was big of you to admit that....could use more people doing that on the internet. :))@@beestoe993
@edluttrell2228
4 ай бұрын
You’re doing good until you mix the JB weld with gloves, not recommended by anybody
@1221Ralph
3 ай бұрын
Exactly. I was like hmm good job until I saw the freaking glove mixing of the jb weld and using blue shop towels. WTF lol.
@EngineeringHooksets
3 ай бұрын
yeah wtf is this guy thinking
@chrisparker9886
Жыл бұрын
If you want it done the right way you would tig it! 😁
@EngineeringHooksets
Жыл бұрын
Yeah, welding is definitely the best way. But the truth is, on a cheap aluminum boat, its probably not worth paying someone $100/hr to fix a leak.
@kewintaylor7056
Жыл бұрын
No sanding?😮🤐
@EngineeringHooksets
Жыл бұрын
Why would I sand it? The wire wheel is sufficient to remove paint, and a rough surface allows adhesive to bond better than a smooth surface.
@jackskellington4351
Жыл бұрын
Yeah I would never put a bandaid on my boat if it's aluminum weld the aluminum and if you know how to use brazing rods you have the boat heated to the right temperature will suck the brazing rod down into the crack of the boat able actually Bond to the aluminum what you did is the same thing the previous owner did with the JB weld it'll work for a while but for someone like me who is putting a Bass boat floor and subfloor and my metal boat and I don't want to have to tear it apart to re-fix a leak when my silicone starts falling apart I will just weld aluminum
@christhomas1465
6 ай бұрын
Think it depends on the boat. I agree weld is superior, but if the boat is full riveted, you run the risk of blowing out a seam seal by overheating it while welding. Heat sinks while welding help, but ya better know what you're doing.
@jeremyford9806
2 жыл бұрын
Great Video!! A simple drilled hole CAN be brazed. A spider crack like what he is dealing with is cracked because it is under stress and takes a fix like this. What he is doing will definitely work and then some!!
@martyhonda6983
2 жыл бұрын
try a bondo plastic spreader for JB weld
@EngineeringHooksets
Жыл бұрын
Good tip
5 ай бұрын
Welding is still the best way to fix. Aluminum rod for Aluminum boat
@EngineeringHooksets
5 ай бұрын
Yes, but legit aluminum welding on a 1/16" boat hull is incredibly difficult, and 99.9% of people are unable to do that. This video is for the rest of us.
5 ай бұрын
How do I know welding is the proper way. Because I work for Tracker boats in Bolivar, Mo.
@EngineeringHooksets
4 ай бұрын
Yeah okay because we all have the equipment and skills for aluminum welding 🙄🙄🙄
@sailboatbob3969
5 ай бұрын
I think i'd use a rubber scraper. mix the JB weld with a stick then spread it with what they use to put on body putty. I just think you'll get a cleaner, smoother outside patch, less drag
@EngineeringHooksets
5 ай бұрын
Yeah that's probably smart
@Heraclitean
2 жыл бұрын
Good way to waste a lot of JB Weld.
@EngineeringHooksets
2 жыл бұрын
?
@mv5499
6 ай бұрын
Mix on cardboard... then use a flat edge to apply... mixing str8 into ur hand won't be a consistent mix, and you waste a majority of the product in ur gloves
@Enjoy_my_1st_Amendment
2 жыл бұрын
Yep always try to keep one hand clean forsure! Your phone wont ring all day until you start messing with stuff like that lol. Then everybody calls at the same time it seems.😂
@EngineeringHooksets
2 жыл бұрын
Always!
@bajadan2769
Жыл бұрын
use a stainless wire brush to avoid inbedding iron into the aluminum .
@EngineeringHooksets
Жыл бұрын
Good tip
@JasonSipe16
6 ай бұрын
Or brass
@chrisbrownson7154
2 жыл бұрын
I hope to never have to use this but super informational! Great video, Matt.
@EngineeringHooksets
2 жыл бұрын
Hope not. Thanks, Chris!
@BackroadsAngling
2 жыл бұрын
Looks like a nice patch. Should be good to go! Team Brazing Rods be gettin clowned up in here.
@EngineeringHooksets
2 жыл бұрын
Lmao
@mikepierson7447
7 күн бұрын
I have had great success with those brazing rods they are cheap, fairly simple to use, and have stood the test of time when done properly. But I feel the patch is way better for this scenario. Different tools for different problems
@DavidRostie
22 күн бұрын
Thank you for sharing this video! I have a crack right along the seam of the back of the boat, just below the transom (16ft foot aluminum). Not sure if I should drill a hole at the end of this crack, as it's right along the seam, where the back meets bottom? I wish I could attach a picture... Would love to hear any thoughts.
@jaybae8056
2 жыл бұрын
you are the first person i have EVER seen mix that 2 part epoxy with hands. are you Canadian, and/ or are you Polish? lmao
@EngineeringHooksets
Жыл бұрын
No. I don't see why that wasn't a good idea? If I mixed it on a paper plate or something I'd have to use and then waste the plate and some sort of mixing stick. By doing this the only extra waste was my gloves, which would have been thrown away anyways. And I still got enough JB Weld to apply a solid patch.
@jaybae8056
Жыл бұрын
@@EngineeringHooksets lol. great video. thank you again.
@claytonwodham6916
5 ай бұрын
lol
@MrElmaat
2 ай бұрын
Most polish people are significantly more intelligent and knowledgeable than any American
@tahkonajones2733
Жыл бұрын
Just traded a laptop for a 1969 seaking has atleast 3 cracks that I know of I was about to get braising rods but this seems alot more sturdy thanks man
@EngineeringHooksets
Жыл бұрын
Good luck with your boat!
@christofervandezande8853
12 күн бұрын
i like the overall process for your fix, but those methods are fucking wild. just mix the jbweld with your hand? what?
@EngineeringHooksets
12 күн бұрын
@christofervandezande8853 why waste a paper bowl (or whatever other mixing surface)? It mixed fine the way I did it
@thedutchman8793
2 ай бұрын
This guy has absolutely no idea what are you doing or talking about!! Brazing will work perfectly fine you just need to be smart enough to anneal the braze afterwards so if softer and flexible instead of hard and brittle🙄🤦♂️ but I bet this guy has zero formal education in welding, engineering of any kind of even a basic knowledge of metallurgy!! If you really wanted to do it correctly you would tig weld it! Only thing he did correctly was drill out the ends of the cracks....but even my 5 year old knows enough to do that🙄
@EngineeringHooksets
2 ай бұрын
You bet I have zero formal education in welding or engineering of any kind? First of all, why lump engineering in with welding, as if they're at all related 😂? Second of all, that's hilarious because I'm literally a geotechnical engineer.
@chrisroa1
Жыл бұрын
FINALLY! Thank you for speaking up and showing others how to PROPERLY perform this repair. Great job! I posted a very similar video years ago and was attacked for such a "flimsy" repair...this is THE BEST WAY to repair a small aluminum boat leak if caused by fatigue cracks, splits or minor-moderate hull breaches.
@EngineeringHooksets
Жыл бұрын
Thank you for the comment!
@ZPDSurvival
Жыл бұрын
That's how you do it. Awesome.
@jaimel8254
Жыл бұрын
No dont do this unless aluminum is totaly cracking 5200 marine sealant will last your lifetime but the real fix is brazing Not welding its very easy with mapp gas and rods from harbor freight Im a very seasoned tourist torney and commercial fisherman This kind of repair is for aluminum corrosion problems
@spicky2966
Жыл бұрын
my thinking as well
@EngineeringHooksets
Жыл бұрын
I completely disagree. Braze rods do not adhere well to a flat surface because you are not melting the hull of the boat. The repair in this video is 1) more waterproof and 2) more durable.
@allenhughes12
Жыл бұрын
@@EngineeringHooksets yeah. Don't do it this way unless the aluminum is totally cracking. Kinda like your's I guess. 😂
@6cwl9
2 жыл бұрын
Man I saw this just in time I would have been trying to learn how to braise and probably done more harm than good. thank you
@EngineeringHooksets
2 жыл бұрын
Glad I could help you out! Gl with the repair
@sgib199
10 ай бұрын
Great video! For what it's worth, the Loctite PL Marine that you used is more like 3M 4200 than 3M 5200. Loctite PL has same hardness rating as 4200, and 5200 has a higher hardness rating (less flexible, but a stronger bond). Have you used both 5200 and Loctite PL to do this and had equal success? I've got a leak that is under the end of a rib on my boat. I really like the technique you are showing, but will have to remove the rib to do it. A little worried about doing that.
@EngineeringHooksets
10 ай бұрын
I used 5200 when I bolted on my transom board, I got them confused in this video. I have not used 5200 to repair cracks like this, though.
@hectorsandoval6817
Жыл бұрын
Creo es más fácil y más seguro instalar nuevos remaches en los orificios! No creen
@johnbooker7322
Жыл бұрын
Okay, but how to fix a broken corner support/ rear, left corner of the boat. I am the 2nd owner of my boat. Whoever had before I did either backed it into something, or someone hit the boat. The seam is broken, and corner cap "welded" is just gone it was broke off when I got it. How do I fix that?
@EngineeringHooksets
Жыл бұрын
I do not know, sorry. You should probably take it to an aluminum welding shop.
@JasonSipe16
6 ай бұрын
Take it to a tig welder
@InvaderMyk
Жыл бұрын
So, your superior repair is to protect your sealant with metal instead of just using metal? Please do not become a roofer.
@EngineeringHooksets
Жыл бұрын
I'm gonna go install a new roof on your house out of spite
@James-gr6lx
2 жыл бұрын
Thats a…..an interesting way to prep and apply jn weld 😂
@EngineeringHooksets
2 жыл бұрын
Lol
@aquaterrafootage9547
Жыл бұрын
Nice job I'm going to use a putty knife and plate when I mix and apply my weld.
@EngineeringHooksets
Жыл бұрын
Haha yeah thats probably smarter than what I did
@NochNi
8 ай бұрын
Great video. Got my subscription with this one.
@DustinDIY
2 ай бұрын
Better way is 2 pieces of thin aluminum. 5200 between both and rivets around the patches holding them in together.
@thomasclayon9143
Жыл бұрын
Thanks for making this video, I just bought a 1982 Lowe 1648 yesterday. Tons of work that needs to be done. It had a 60 horse evinrude and a jack plate. Left 4-1/2 inch holes. Would you suggest this to fill those holes like this, jb weld or should I braze them solid?
@EngineeringHooksets
Жыл бұрын
You mean a circular hole with a 4.5 inch diameter? I've never fixed a hole that large so I'm not qualified to answer that, sorry. This video is intended for small holes and cracks
@thomasclayon9143
Жыл бұрын
@@EngineeringHooksets no, I mean 4 holes a 1/2 inch in diameter where the jackplate was bolted on
@danielgarza2385
Жыл бұрын
I would braze them
@claytonwodham6916
5 ай бұрын
Very good helpful to me. 25g subscribe must have some other good tips. Gd job.
@johnmacmillan627
Жыл бұрын
Great info! Thx
@brucemoulton8876
2 жыл бұрын
Yes, thx, the patch was under my middle seat.
@EngineeringHooksets
2 жыл бұрын
Glad I could help
@MostlyPosative-nj5ex
6 ай бұрын
Who are you to claim that brazed repairs aren’t going to work? I bought a bought years ago that had circular saw cuts in it because the previous owner thought it made a good plywood cutting platform. I brazed those gouges and holes closed with patches and aluminum brazing rods. I turned it into a jetjon and it rips through chop and waves all the time. Those repairs are still holding. No water gets into the boat from the bottom.
@EngineeringHooksets
6 ай бұрын
Who am I? Oh, just a guy that brazed 3 holes on my boat, and they all started leaked at some point. And no, I don't think I did a particularly bad job or anything. If brazed patches are working for you, you're probably not bumping your boat into any rocks or stumps. Brazed patches fail when the hull flexes
@rickfuerst2553
2 ай бұрын
I'd TIG weld it.
@EngineeringHooksets
2 ай бұрын
That would be ideal, but the reality is most people don't have the equipment or skills to do that, so we gotta make due
@matthewlee8068
2 жыл бұрын
this is the best video so far. i know what il do now.
@EngineeringHooksets
2 жыл бұрын
Thanks for the comment!
@FishinOnaMission
2 жыл бұрын
@@EngineeringHooksets can i do the side of the hull where the water line is? And the lower back where the transom is?
@EngineeringHooksets
2 жыл бұрын
@@FishinOnaMission you should not do this on the outside of the hull. The patch could catch on a rock/debris and rip off, possibly jerking the boat in that direction.
@EngineeringHooksets
2 жыл бұрын
@@FishinOnaMission Not sure if I misunderstood your comment but I took what you said as asking if you could invert the patch, with the aluminum and 5200 on the outside.
@herb1959
Ай бұрын
how is the patch working
@EngineeringHooksets
Ай бұрын
@herb1959 fantastic. Doesn't leak a drop
@herb1959
Ай бұрын
@@EngineeringHooksets thank you. I have a alumacraft with a nasty hole to fix. I wish I could send a pic good weekend.
@peace4peaceful
8 ай бұрын
I sure as will not be doing this fix. Can't even mix epoxy! 😮
@EngineeringHooksets
8 ай бұрын
Relax bud, I was just trying to save using a paper plate. And the epoxy mixed just fine.
@robbiej2805
5 ай бұрын
Why didn't you weld first
@allenhughes12
Жыл бұрын
Seems like the 5200 would keep you from bleeding if you cut your fingers on the aluminum.
@EngineeringHooksets
Жыл бұрын
Lol
@claytonburch5181
11 ай бұрын
I would have riveted it in if i was you
@TS-eg8dm
11 ай бұрын
I would trust that patch without installing some closed ended all aluminum rivets
@EngineeringHooksets
11 ай бұрын
Well it's been working great ever since
@justinbenscoter2052
5 ай бұрын
Life is so much harder when you don’t have a tig welder.
@EngineeringHooksets
4 ай бұрын
true
@ricocortez5827
3 ай бұрын
Mixing JB weld on with your hand is insane
@EngineeringHooksets
3 ай бұрын
We do a little insanity
@webincomeincome8767
2 жыл бұрын
Might consider using latex mechanics gloves next time.
@EngineeringHooksets
2 жыл бұрын
You mean for the JB Weld? I think the gloves I used in this worked well enough. Sure I lost about 33% of the material but I still had plenty.
@BillaBong1
Жыл бұрын
nah i rather use brazzing rod and sand it down and repaint with some gatorglide.
@EngineeringHooksets
Жыл бұрын
Sounds like you already know what you're doing, why are you watching youtube How-to's?
@BillaBong1
Жыл бұрын
@@EngineeringHooksets just browsing around on youtube for different tips and tricks and how tos, to refresh my mind and find new ideas on my daily diyer ability to work with different stuff lol
@johncrouch5778
Жыл бұрын
The heck you doing with that JB
@EngineeringHooksets
11 ай бұрын
Just vibing
@michaelthomas9992
5 ай бұрын
Guys
@EngineeringHooksets
5 ай бұрын
Gals
@SirJ18
5 ай бұрын
😂
@EngineeringHooksets
5 ай бұрын
🤣
@yeslawrence
2 жыл бұрын
What do u recommend to fix a leaking rivet on an aluminum boat?
@LorenBast
Жыл бұрын
Try this kzitem.info/news/bejne/0oGHx59uiHaSdJw
@EngineeringHooksets
Жыл бұрын
Ive never fixed a rivet but probably drill and replace with a new rivet + 5200 sealant
Пікірлер: 128