Just came across your channel now. I'm going to steal your method to mount the ultrabell. Those o-rings are a pain. Thanks for including part nbrs and source.
@BigFun4Life
2 жыл бұрын
Can’t wait to see it in action..Great build Mr…Can’t wait for your next video always look forward to them..
@mountainsgarage
2 жыл бұрын
Thanks! Always enjoy your positive comments!
@comp1911
2 жыл бұрын
One thing I picked up fro Reid was to run bushing/busing or roller/roller and not mix from a concern of the oil following least resistance and passing through the roller side and leaving the bushing dry. Not sure if there is any merit to that but worth a comment. Keep up the great content!
@MHolt3573
2 жыл бұрын
Love all the info on the power glide transmissions.
@Scofflaw_k10
2 жыл бұрын
This has been fantastic! Thank you Sir!
@3050fabVillainNova
2 жыл бұрын
because racecar!!
@jamieknight9636
2 жыл бұрын
Great vid Shawn, thx for helping the fellow man
@sethster70
Жыл бұрын
Sheww looked up that gear set, man they’re proud of them.
@JOMaMa..
2 жыл бұрын
thank you for sharing your knowledge 👍
@njclsx4252
2 жыл бұрын
The bte parts looks like top quality
@danielharms5489
2 жыл бұрын
Is good idea to keep ears on bellhousing, can run a tap through them then use as mounting point for blanket.
@daltonnapier590
2 жыл бұрын
I realize this video is about 4 months old but a full cost video wouldve been cool
@mountainsgarage
2 жыл бұрын
Never too late!!! Thanks
@funfun8095
2 жыл бұрын
You need to get it in the car and the car running, asap, before you sell this "Your" transmission! LOL Will be cool to see you getting these builds running, tuning, and driving, too.
@mountainsgarage
2 жыл бұрын
For sure! I got smart and build myself two of everything just in case!
@jamieknight9636
4 ай бұрын
Hi Shawn, im building a Powerglide atm for a 400hp street car and your videos are invaluabe, thx. One thing, am i able to convert the standard valve body to full manual and do away with the governer? perhaps you could do small vid on what to do ?
@gregsmith9457
2 жыл бұрын
👍👍👍
@WayneBillings-ht4pl
Ай бұрын
Did you install servo tube? It was missing when you installed the pan.
@mountainsgarage
Ай бұрын
Good eye, I mentioned I had forgot it probably in the next video!
@pauldocherty8314
4 ай бұрын
Any cheap way to convert a fixed yoke glide to slip shaft setup?
@lostinthewoods6474
2 жыл бұрын
Did I miss the weather report????
@MHolt3573
2 жыл бұрын
Do you prefer to use Vaseline rather than the assembly goo?
@mountainsgarage
2 жыл бұрын
I use both, depends on the mood and the shop temp. Vaseline is much cheaper and wipes off easier.
@carltotillo8301
2 жыл бұрын
Isn't there a tube that feeds the servo for the band?
@mountainsgarage
2 жыл бұрын
Yes. I cover that in the video, the part about me forgetting it!
@carltotillo8301
2 жыл бұрын
@@mountainsgarage Yes, I paused the video to send the comment.
@mountainsgarage
2 жыл бұрын
@@carltotillo8301 I am still mad at myself!
@jamieknight9636
2 жыл бұрын
Shawn, when using the deep pan with the filter extension perhaps it's not necessary to fill to the 3/4 inch above pan rail level?
@mountainsgarage
2 жыл бұрын
That would defeat the reason for having a deep pan, that would just be lowering the level away from the transmission. The correct full mark stays the same. Good thought process, I like idea exchange!
Пікірлер: 30