This is *actually* the easiest of all the "easy" ways to remove a stuck case I've seen so far! Thanks
@eric802
3 жыл бұрын
Good method, as long as there's enough brass sticking out to hold in the vise. Last one I got stuck was all the way in the die and the rim ripped off on the downstroke; next to nothing left to grab onto. That's when the drill-and-tap procedure is needed.
@tonyc.4528
2 жыл бұрын
1/4-20 and a spacer...yup. Never seen that much sticking out before, always buried.
@chenjohn9115
2 жыл бұрын
wowowowowowowowowowowow, you are my hero... 4 * 223 Remington full length die got stuck because I use a lot of range cases. Now all dies get back to the press after I watch this video.
@RetrieverTrainingAlone
3 жыл бұрын
I've been hand loading since the 1980s and have never had a stuck case. That said, it is nice to know how just in case. Thanks.
@Hisslave1
3 жыл бұрын
You are blessed indeed! I've been at it since '81 and have had a few.
@danjohnson6870
2 жыл бұрын
In the many years I’ve been at it, never stuck one either
@HypocriticYT
3 жыл бұрын
finally someone who does this without drilling. I do the same but I turn the die with a wrench to loosen the case and then tap the die rearward with a leather mallet to remove it from the neck expander..
@mcentirejerry
3 жыл бұрын
Just stuck a 30-06 this morning! Thanks for the trick, now I'm setting here thinking why didn't I think of that!
@draczka14225
3 жыл бұрын
Worked perfectly!! had a stuck case in an RCSB die that doesn't allow your to remove the decapping pin from the top.. so couldn't use stuck case removal tool.. actually ordered another die to replace then came across this video..
@gerrymatheson4020
4 жыл бұрын
Wow...this is ingenious and the most simple method I've seen yet. Makes me almost want a stuck case so I can try it out...almost... Love that it involves no drilling or tapping! I use Hornady Unique lube/sizing wax. It's very similar to Imperial but less expensive...
@mattjohnston5786
5 жыл бұрын
Thank you! You saved me from buying a new die. 5th brass I inserted into my decaping die got stuck tight. It was 300 aac brass, so I didn't have much to grab with the vise, so I screwed a screw into the primer pocket and locked the vise down onto the screw. The rest of your method worked like a champ. Whew.
@balanceandbodymechanics1355
3 жыл бұрын
You're not using enough lube. I found that if you use a small tubing cutter ($12) to cut the case in two everything comes apart easily. I will have to try this guy's technique the next time
@codynoeller24
3 жыл бұрын
Thanks to this I was only without a die for 20 minutes, of which 15 was looking for a solution!
@mohammedcohen
3 ай бұрын
WOW!!! Thanx...only had one case ever stuck but even with the removal tool I couldn't remove the case and wound up sending the lot to, IIRC, RCBS...
@corylanders1154
7 жыл бұрын
this was my last chance since tapping didn't work. you method was a lifesaver bro. thanx for posting video
@andyf80
7 жыл бұрын
Cory Landers nice! Glad it helped. It's helped me quite a bit until I started using Imperial Sizing Die Wax. The stuff is amazing! The range where I collect brass is SUPER sandy and is murder when it comes time to size, even after tumbling I find sand lodged in some shells, but a good amount of the wax works wonders. They say 'use sparingly', but I have to use more than most folks as it will still stick in the die if I'm not careful.
@bufallobiff
3 жыл бұрын
That's all well and good except that a fully inserted cartridge won't give you that much left out for your vise to grab.........
@andyf80
3 жыл бұрын
This is what makes reloading fun for all ages. Thanks for watching.
@doubled473
3 жыл бұрын
This case isn’t really stuck but trust me this works? Outstanding.
@brandonbadua
6 жыл бұрын
You saved me from going insane. Thank you Sir!
@rpap5322
3 жыл бұрын
how did you remove the de capping pin and the ball expander... without damaging those parts...
@lberthelon
5 жыл бұрын
By far the easiest way, thank you.
@johnchausow4857
7 жыл бұрын
You sir are a freakin genius. Thanks! Way better than drilling and tapping.
@AlmiraAbsin
2 жыл бұрын
Excellent way to remove a die. I remember this one.This was genius
@winder4850
7 жыл бұрын
Works great! By far the easiest method.
@shadetreelife3670
5 жыл бұрын
I suggest you put some grease on your nail, that will keep it from falling out. Great idea, thanks!
@gwpattrick
5 жыл бұрын
That's the best idea yet cheap and easy
@le3045acp
3 жыл бұрын
that does not work when the case is only the rim sticking out and the web of the case is in the die or id didnt for me in the past
@andyf80
3 жыл бұрын
This is what makes reloading fun and rewarding for all ages.
@1911geek
3 жыл бұрын
An interesting method but very logical and practical crafty way to resolve stuck case indeed
@bfdadventure
Жыл бұрын
WOW! Genius! Thanks for making the video!
@ReelTimeCapt
3 жыл бұрын
Very cool and thank you.
@GregDaGoblin
6 жыл бұрын
Haven't had one stuck...yet. But using the massive threads already on the the die looks much easier then tapping the casing. :D
@rpap5322
3 жыл бұрын
you will have a better chance of removing the stuck case using the tap versus damaging the de capping pin and or ex pander ball... if you crush the case at the base and it does not come out, then the real problems begin....
@coltonjaynes1605
2 жыл бұрын
Saved my day!
@geraldf.1222
Жыл бұрын
There's nothing smoother than the Dillon Stuck Case removal feature on their 223 sizing die... That said, I like the Hornady and RCBS removal kits that extract via a drilled and tapped case head. If you don't have a vise, that might be your best bet.
@adamthatguy454
3 жыл бұрын
Putting the die and stuck brass in a deep freeze prior to doing this will help too.
@margaritaweeber9234
3 жыл бұрын
Thanks! You’re a lifesaver!!!
@dukeman7595
Жыл бұрын
All you have to do is Tap it out from the front with a punch. Much easier that your way.
@harteverett
3 жыл бұрын
Nice to know but I’m thinking most stuck cases don’t protrude nearly that far, possible tho you could still get a hold on the case head, hope I’ll never have to use it
@blueridgeboy6791
Жыл бұрын
Way easier than drilling an tapping. Both work this is just simpler.
@psmith535
2 жыл бұрын
Thanks
@wemcal
3 ай бұрын
Great information
@JamesJohnson-ci3km
2 жыл бұрын
Wonderful, thank you
@Andrew-jm4tp
4 ай бұрын
I wish I would have seen this video first. I watched a bunch of other videos with more complicated solutions.
@donaldslayton2769
5 жыл бұрын
I have a 1/4 :20 tap, drill ,bit and bolt/washer next to my press. It doesn't happen often, but when it does, I'm only down for 3 minutes tops
@jeffmorrow1957
3 жыл бұрын
Thanks Man👍
@le3045acp
3 жыл бұрын
i see where the gentleman put the screw in it that was my sugestion when the brass is stuck deep in the die
@DracironSmith
4 жыл бұрын
Sadly didn't work on a 30.06 case. Just tore up the base of the case even more. Great idea though. Wish it'd worked.
@frankkee8709
Жыл бұрын
Thank you
@karthikr2151
4 жыл бұрын
Oh brilliant!!!
@TacticalFellowship
5 жыл бұрын
Crap YES! Thanks brother!
@brandonbowerstx
5 жыл бұрын
You just saved me 29 dollars (35 Whelen)
@RangerCaptain11A
4 жыл бұрын
why can't you do that while on the press? the brass is held by the shellholder.
@gerrymatheson4020
4 жыл бұрын
I don't have any experience with this (yet) but I've watched lots of videos of several different methods. Often with a stuck case the shell holder has been ripped off the base head, usually damaging the brass. Also the die needs to be able to freely move up as you turn the lock ring down with the crescent. If it's threaded into a press it can't move upward freely.
@barrygrant2907
3 жыл бұрын
It will rip the rim off.
@steveobee3488
5 жыл бұрын
I just used a old lee decaping pin that the pin was broken off two small taps with a mini ball peen hammer from harbor freight and presto out and back in business
@rpap5322
3 жыл бұрын
How did you remove the good decaping pin and the expander ball with out damaging them ????
@Billbobaker
3 жыл бұрын
Great video thanks for sharing it
@goodboyringo9716
Жыл бұрын
I tried this and it still wouldn't come out until I heated the die then it came out.
@92xl
2 жыл бұрын
Lube them up real good, boys!😉
@Aereaux
3 жыл бұрын
Buy a good set of open and box wrenches and ditch crescent wrench. I know they work, but to big of a chance to round over the hex on the nut.
@tires2burn
Жыл бұрын
When I get em stuck there is never this much case sticking out.
@rowlandisbeautiful
10 ай бұрын
WDITOT ?
@slipknnnot
3 жыл бұрын
I bought a truck just for this method... unfortunately it didnt work because my case was stuck balls deep
@losonsrenoster
Жыл бұрын
Easy as pie. 3.14....
@DL101ca
Жыл бұрын
Gotta spit on it brah...
@SD-yb5fx
3 жыл бұрын
Why not make sure that you are truly saved by Jesus Christ and practice this way. Remorsefully confess with your heart your sins to Jesus Christ who is God and tell Him that you right now are repenting of your sins and you want to be born again of the Spirit from above. Tell Jesus that you are remorsefully sorry for breaking His commandments and that you are begging for forgiveness from Him. Allow His blood from the cross to wash away your sins. After this is done with your heart successfully the Holy Spirit will come to live within you and He will rebuild you from the inside out. Look for signs that you are saved. Things like spreading the good news from Jesus, getting other people saved, a craving for the word of God, reading the Bible, etc… These things are known as a calling and fruit bearing. If you're not bearing fruit then keep doing it. Sometimes it takes time to get saved. Read Matthew chapter 13 from the King James Bible. God bless!!!
Пікірлер: 74