Great video Spiros and some very useful tips,especially for anyone just getting into wood turning because sooner or later a stuck chuck going to happen. In the past I have got the mother in law to glare at it ....... that always works ;) so these tips will save her from coming here to sort it out ... Many grateful thanks Bram :)
@spwoodart
7 жыл бұрын
Bram the Wadesmill woodturner lol thanks for watching my friend. Also thanks for your kind words. I know what you mean about in laws.
@jakewhicker
5 жыл бұрын
Just bought a used lathe, with a nova 3g stuck on it. The heavy metal bar chucked up snug, a shot of wd40, and a couple whacks with a hammer and it came free. Really enjoyed your video, and thanks for the tips!
@spwoodart
5 жыл бұрын
jakewhicker awesome! Thank you!
@adamjustice7452
3 жыл бұрын
Thanks for the video. A great tip for getting a stuck adapter out of a chuck that is off the lathe is to attach the jaws only the legs of your lathe then use a wrench. Thanks again
@spwoodart
3 жыл бұрын
Thanks for watching, glad it helped!
@ivanstern2771
4 жыл бұрын
This presentation was just what I needed! Now, I'm trying to apply one or two of the methods. At present, I'm try to apply some heat to the stuck assembly on the idea that the metal, at least on the faceplace, will expand enough to allow remove. In any case, thanks for a complete review of all the methods!
@spwoodart
4 жыл бұрын
Ivan Stern glad I can help or hope that I can. I didn’t mention all the possible methods but those were some that worked for me. I also use the plastic rings now to avoid that issue and there is little run out in doing so. I have not had a stuck chuck since. Thanks for watching and commenting. Cheers!
@petercallaghan4718
7 жыл бұрын
Thanks. I have a stuck chuck and will try your suggestions.
@spwoodart
7 жыл бұрын
Peter Callaghan no problem, I hope you are able to remove the chuck. Thanks for watching.
@anamericanartisan9846
6 жыл бұрын
Very Helpful.
@spwoodart
6 жыл бұрын
An American Artisan thank you, I’m glad! Cheers!
@billk8579
7 жыл бұрын
Great informative video. New to turning. Have not had a stuck chuck yet, but probably only a matter of time.
@spwoodart
7 жыл бұрын
Bill K awesome, that's exactly why I put this video out there to help. Hopefully you won't have a bad one. Thank you for watching.
@grahamparkinson8258
6 жыл бұрын
Thanks for this, got my stuck chuck off. Soaked over night with wd40. Used a piece of leadwood to support a hole punch in the shaft. Secured with duct tape and a long bar in the chuck Jaws. Came off no problem.
@spwoodart
6 жыл бұрын
Graham Parkinson thank you, and I’m glad you got the chuck off. Good idea with the hole punch.
@jackmaravola2496
7 жыл бұрын
Been there and done that...! Lots of great information....! Thank you for sharing....! Very informative......!
@spwoodart
7 жыл бұрын
Jack Maravola thank you, glad you liked it.
@paulwestra1370
5 жыл бұрын
Thank you - this was very helpful.
@spwoodart
5 жыл бұрын
Paul Westra thank you for watching
@kwstasantwniou243
7 жыл бұрын
Nice video and very helpful Spyros really enjoy it
@spwoodart
7 жыл бұрын
Kwstas Antwniou thank you sir!
@therevngraham
6 ай бұрын
So, I’ve finally got a chuck stuck. Didn’t know it was a thing. But it’s very much a thing. Can’t get it off… and I’m said. It’s halting production. Will try soaking it first. My question is does this damage how the front and back line up? Will they still be on center? Or will I have to figure out how to make the head stock and tail stock align again ? Thanks.
@spwoodart
6 ай бұрын
It’s only a matter of time for a Chuck or face plate to get stuck. The lathe should be fine and inline as long as extreme measures were not taken. It also depends on the lathe. Most lathes can be re-aligned. Hope you can get the chuck off. Cheers!
@therevngraham
6 ай бұрын
I got it. Thanks for the help.
@Jerzee609
7 жыл бұрын
I don't turn wood, but I'm 100% sure this video was very helpful to many others. I'm just here for the wood lol.
@spwoodart
7 жыл бұрын
A Gad thank you and thanks for the feedback. Lol
@pjbaddict
7 жыл бұрын
Great helpful vid... just a quick tip, if you are going to grip your spindle with vice grips, try some thin copper or aluminium sheet between the teeth and the spindle... it won't compromise the grip but it will stop the damage to the spindle
@spwoodart
7 жыл бұрын
Glyn Senior thank you and thanks for watching. That is a great 💡 idea. Not sure why I never thought of that. Thank you for the tip. Take care my friend.
@hiroshiwatanabe7578
7 жыл бұрын
very helpful
@spwoodart
7 жыл бұрын
hiroshi watanabe thank you
@martkt10
7 жыл бұрын
I use a some ptfe tape on the thread and up against the headstock and all shared help is good
@spwoodart
7 жыл бұрын
martkt10 hey that's a great idea. Thanks for sharing and for watching.
@Lee-qp6gf
7 жыл бұрын
I use anti seize by John Deere. Don't know if it helps but haven't had a stuck chuck. Good vid. Cheers
@spwoodart
7 жыл бұрын
Lee Waterman I haven't tried that kind before. I will have to give that a try. Thank you for the feedback my friend and watching. Take care.
@spwoodart
7 жыл бұрын
Hope you like the new informational video.
@stixbymarkbeauchamp8391
7 жыл бұрын
Great info, I have a chuck stuck on a home made lathe. I'll have to soak it with penetrating oil
@spwoodart
7 жыл бұрын
mark beauchamp sorry to hear that, I feel your pain my friend. The oil works for sure, or helps in addition to other methods. Hope you will get it off. Thank you for watching.
@Adam-sh1xx
4 жыл бұрын
Awesome
@spwoodart
4 жыл бұрын
Adam Morrissey Thank you!
@jstarr3676
2 жыл бұрын
Is this for if the chuck won't move or you can't unscrew it? Because mine won't unscrew
@spwoodart
2 жыл бұрын
Correct, should give you some ideas on the subject.
@rickgrant8048
7 жыл бұрын
where did you get the run out guage setup?
@spwoodart
7 жыл бұрын
Rick Grant hi, I bought the gauge on Amazon. Just type in Dial indicator. They vary in price, mine was around $40 US and it's fairly accurate. Thanks for watching.
@tompalmer334
7 жыл бұрын
I tried the plastic washer didn't work for mine Grizzly G0698 then I ordered some washers made of brass this did the trick had to use two of them but they worked and also use them on my Delta lathe it is a 1" the Grizzly is 1 1/4" try it you may like them better
@spwoodart
7 жыл бұрын
Tom Palmer good idea with the soft metal washers. That may cut down on the vibration and run out from the plastic washers. I am going to try those. Thank you for sharing the tip, I appreciate it my friend. Take care.
@rickgrant8048
7 жыл бұрын
Tom Palmer where did you order brass washers from?
@rickgrant8048
7 жыл бұрын
Where did you order the brass washers from?
@tompalmer334
7 жыл бұрын
e-bay is where I found them look them up under copper shims in the size you won't or brass shims
@曹兵伟
7 жыл бұрын
The same model lathe, the same problem! ! ! ! Crazy
@alanmullock381
7 жыл бұрын
rings made from paper work for me and they're free!😆
@spwoodart
7 жыл бұрын
Alan Mullock hey, that's a good idea. I never tried that before. Thank you for the tip. Cheers my friend.
@flugschulerfluglehrer
6 жыл бұрын
Did you really use vice grips on your shaft?!?
@spwoodart
6 жыл бұрын
Flugschüler Fluglehrer I did, it works, but scuffs up the shaft. Not my first choice for a stick chuck, but it’s an option on the inside. Thanks for watching
@lesliekendall5668
6 жыл бұрын
Flugschuler....Yeah, and those darned ol' "teeth marks" will tear you up every time....very painful.
@rotokid4820
7 жыл бұрын
You are on the right track with the strap clamps but you should use a more industrial version. If you use one of these www.zoro.com/ch-hanson-locking-chain-clamp-20-72000/i/G4861011/ directly behind your chuck (your lathe may have a better location to clamp) Then use a wrench on the chuck flats it is much easier.
@garyirwin4078
7 жыл бұрын
put a plastic, or fiber washer behind chuck.
@spwoodart
7 жыл бұрын
Gary Irwin that's a good idea. I showed that at the end of the video. Lol thanks for watching.
@FUBuddy
6 жыл бұрын
lug wrench in chuck
@spwoodart
6 жыл бұрын
F.U. Buddy good idea. Thanks for watching.
@dennisbeamish9058
7 жыл бұрын
Hi I would rather see turning videos! Dennis Beamish Cambridge Ontario Canada
@spwoodart
7 жыл бұрын
Dennis Beamish thank you for the feedback. I'm sure the next video will be a project video. Thanks for watching too.
Пікірлер: 62