⬇️⬇️ (English translation below the Italian text) ⬇️⬇️
0:00 - Suoni dei piani armonici liberi
0:12 - La tavola e il fondo del violino liberi dalle fasce producono alcune note alla percussione che corrispondono a modi caratteristici di vibrazione, denominati a partire dal più basso in frequenza M 1, M 2, M 3 e così via al salire della frequenza. Per eccitare un modo, tenere la tavola con due dita lungo una linea nodale (zona di non movimento) battendo con il polpastrello dell'altra mano in un'area antinodale (zona di movimento) ascoltando la nota prodotta.
0:25 - I modi più utili per il liutaio sono M 1, M 2 e M 5 chiamati anche modo a croce, modo "X" e modo ad anello con riferimento alla geometria delle loro linee nodali. Corrispondono alle flessioni torsionali, laterali e longitudinali che si effettuano con le mani durante la lavorazione per testare la flessibilità delle tavole. Il Modo 5 è l'indicatore più efficace della rigidità in rapporto alla massa e può essere preso come utile riferimento durante la lavorazione degli spessori delle tavole.
0:43 - Fondo - La mia preferenza è per un M5 compreso tra Fa e Fa# (da 350 a 370 Hz), un peso compreso tra 95 g e 115 g (densità del legno compresa tra 0,55 e 0,65 g/cm3) e per una discreta rigidità della parte centrale associata ad una buona flessibilità nella parte superiore, inferiore e alle punte.
1:06 - Tavola - Con le effe tagliate e senza la catena il M5 dovrebbe essere attorno a Re# crescente (313/320 Hz), in modo da ottenere una nota finale tra Fa e Fa# (da 350 a 370 Hz) con una catena di peso e dimensioni adeguate (peso della catena tra 4,0 e 4,5 g). La mia preferenza per il peso finale della tavola con catena è da 62g a 72g, per la densità del legno la mia preferenza è da 0,38 a 0,40 g/cm3, ma tra 0,34 e 0,44 g/cm3 può andare bene se si utilizzano arcature e spessori adeguati.
⬇️⬇️ (English translation of the Italian text with timestamps) ⬇️⬇️
0:00 - Tap tones of free violin plates
0:12 - Violin top and back plates free from the ribs produce some notes to the percussion that correspond to characteristic modes of vibration, called starting from the lowest in frequency M 1, M 2, M 3, and so on as the frequency increases. To excite one mode, hold the board with two fingers along a nodal line (non-motion zone) by tapping the fingertip of the other hand in an antinodal area (motion zone) while listening to the note produced.
0:25 - The most useful modes for the luthier are M 1, M 2 and M 5 also called cross mode, "X" mode and ring mode with reference to the geometry of their nodal lines. They correspond to the torsional, lateral and longitudinal flexures that are carried out with the hands during working to test the flexibility of the plates. Mode 5 is the most effective indicator of the stiffness in relation to the mass and can be taken as a useful reference during the thicknessing of the plates
0:43 - Back plate - My preference is for an M5 between Fa and Fa # (from 350 to 370 Hz), weight between 95 g and 115 g (wood density between 0.55 and 0.65 g / cm3) and for a fairly good stiffness of the central part associated with good flexibility of the upper and lower bouts and at the corners.
1:06 - Top plate - With the F-holes cut and without the bassbar the M5 should be around D# sharp (313/320 Hz), to obtain a final note between F and F# (350 to 370 Hz) with a bassbar of proper weight and dimensions (bassbar weight between 4.0 g and 4.5 g). My preference for the final weight of the Top plate with bassbar is 62g to 72g, for the density of the wood my preference is 0.38 to 0.40 g/cm3, but between 0.34 and 0.44 g/cm3 can be fine if proper archings and thicknesses are used.
Index of all my videos on violin making:
English: davidesora.altervista.org/vid...
Italiano: davidesora.altervista.org/video/
Davide Sora® is a registered trademark
Davide Sora® è un marchio registrato
#costruzioneviolino #violinmaking
Негізгі бет Suoni dei piani armonici liberi - Tap tones of free violin plates
Пікірлер: 25