Years ago, I was an Installer of A/V equipment in the Detroit area, and we worked through rebar concrete construction ... we drilled it with Diamond coated SDS drill bits and alternated to steel when the progress slowed down due to the metal being hit. Plus, a good cutting oil helps keep the bits cooler. We kept a plastic ketchup dispenser full of oil handy to do this.
@dionh70
Жыл бұрын
Same. I used to install all kinds of low voltage systems, such as CCTV, access control (card readers), alarm, intercom, what have you, and mounting stuff on the exterior of buildings often required drilling through concrete walls with rebar. I would use diamond-coated hole saws for anything over 3/8inch, because I got tired of burning up SDS carbide-tipped hammer bits against rebar. And the cutting oil was also essential, although I had a shallow plastic bowl that I would dip my but in to keep mess to a minimum after a facility manager lost his mind over oil dripping out of the hole and staining the concrete.
@jbowerman50
Жыл бұрын
@@dionh70 that's exactly why I used water, I worked for a school district and that meant someone was gonna bitch
@yoshtg
Жыл бұрын
Also, if its just about getting material off, are there types of jackhammers that could work? battery powered ones? or one with a small generator that you can carry with you? i never used jackhammers myself but its the first thing that came into my mind to remove material off the wall
@aarontoddadventures3817
Жыл бұрын
Yes this should work.
@FishFind3000
Жыл бұрын
@@yoshtg don’t want any gas powered equipment in a mine or to close to the entrance.
@skoitch
Жыл бұрын
I’ve been using KATEYA tipped sds max. They last 10x longer than the high end Dewalt I was using! I like to switch them out often, sometimes 2-3 times on a hole so they don’t overheat. Heat will ruin your best bits
@Woggerdogg
Жыл бұрын
DUDE...YOURE KILLING ME! You do this to us, and I dont know about the rest but it kills me til you post a followup video with the results! Keeps us hanging! And aint nobody going anywhere! HURRY UP! I WANNA SEE!!!! IM DYING HERE! 😭😳
@robtathome
Жыл бұрын
Same!
@ghostprepper5859
Жыл бұрын
Yup
@texasslingleadsomtingwong8751
Жыл бұрын
Lol , me too 😆
@danvigue2238
10 ай бұрын
Same here...
@DayRider76
Жыл бұрын
Your drill bits are for stone and masonry. hitting the iron sulfides is smoking them. On the flip side, if you used a bit for iron, you'd smoke it from hitting stone. I think all you need is to work on technique a little. The mason bits can work, you just have to be sure you only drill into the surrounding rock and try not to hit metals.
@texasslingleadsomtingwong8751
Жыл бұрын
That's kind of my thinking too . Avoid directly hitting sulfide band.
@ut000bs
Жыл бұрын
Ah, good. You have also mentioned he is perhaps drilling into the wrong spots. I agree with you.
@brianmisener177
Жыл бұрын
Yes diamond bits don't like hitting iron just like drilling concrete and hitting rebar!!
@DayRider76
Жыл бұрын
@@brianmisener177 Drilling deck plate and hitting concrete, sucks balls to.
@Klwjjj
Жыл бұрын
I’m loving this channel - absolutely amazing and full of knowledge. I literally stumbled upon this channel yesterday and I’m glad I did.
@TheAuctionProfessor
Жыл бұрын
Very curious were you get the pyramid iron forms you use? Or did your business make them? Looks like it's 1/4" steel sheets? We've been casting metal for 4 or 5 years, and that sure would come in handy.
@deathstarHQ
Жыл бұрын
Great video Jason, i think you need to 'Ask Jeff Williams' so come on, LETS GO!!!
@StirlingLighthouse
Жыл бұрын
You’re really living the dream Jason. Thank you for taking us along! Again, I can’t wait to see the results and see how you deal with the sulphides. Fingers crossed 🤞
@freemai
Жыл бұрын
Perfect way to wait for Dan's Sunday video! Thank you for showing us how much work and science go into mining!
@jonsdigs1
Жыл бұрын
You can use a pump sprayer rig to drill wet but NEVER quench carbide that is too hot to hold or you will crack it! Is that mineral arsenopyrite? Remember how nasty it is when you smelt it.
@daedaluscreation4869
Жыл бұрын
My expectation is that the hardness and crystalline nature of your material is acting like cutting sandpaper. Perhaps not directly drilling into the sulfides and more along the quartz/sulfide transition would do less damage to your bits.
@1topskyrocket
Жыл бұрын
Regarding your drill bit, I've been told from the Sierra blaster company that you should have a dozen of them because you don't want them to get hot just like when your machining metal you don't want it to get hot so you either cool it with some kind of liquid or change your bits out right away and then you'll have them last longer and they won't be damaged as much when you go to a sharpen them.
@jakebrakebill
Жыл бұрын
I always learn something from watching your videos. You should show the backpack you wear with a garage full of tools you must take up with ya. What about a small Hudson sprayer and adjust the tip to spray a needle stream and squirt the hole with water periodically, hopefully keeping the bit cool.
@geneoleary6809
Жыл бұрын
Always a like from me sir
@NET-POSITIVE
Жыл бұрын
Buy a ram set with high power loads and cut stainless steel rods with a chiseled edge, bring ear and eye pro! But this is a powerful solution to a rock-hard vein. Plus it's much lighter to carry.
@Stand.Your.Ground.
Жыл бұрын
Craziest part about all this is we are just mining the “fingers” of the veins. Deep deep deep down is where the body is. Nearly impossible to get to. But if your lucky you’ll get pretty damn close to the hand.
@damianstasek8946
Жыл бұрын
How do we get to it?
@jameshalloran9840
Жыл бұрын
The small bit should about 3/16ths, Burn those up to find your depth "pre-drilling", and chasing that hole with the 3/8ths, 7/16ths, 1/2; which ever one you choose. I don't know which feathering wedges you have, but don't step up several times, it will just cause you misery and waste your time. Just use a pilot hole, and then step up directly to your desired drill size, and keep your pilot hole clean.
@marcozwarionato3509
Жыл бұрын
like u said its mostly metal may an metal dril
@ronshekelson
Жыл бұрын
Drill into the surrounding softer material. I found a small piece of rock like that about 1/2" thick. I tried to drill through it with 1/4" carbide drill and had the same problem. You'll spend more on carbide bits than you'll recover in gold. The good news is hard material is also brittle. You can fracture it with a chisel and heavier hammer. Get a 3-4 lb hammer,
@texasslingleadsomtingwong8751
Жыл бұрын
Hmmm quartz with sulfides , I'm betting either your bits are tool steel tipped. Not tungsten carbide like they should be . If they are tungsten carbide then diamond tipped bits are needed . But diamond tip don't like the hammer drill action only drilling . In concrete those carbide bits work great , but when I get into various types of tiles , porcelain and ceramic those bits burn up while trashing the tile . So , I'd go with diamond tip or verify that they are tungsten carbide tipped . Also try avoiding directly hitting sulfide band.
@rockman531
Жыл бұрын
Hi Jason, Absolutely phenomenal! Your adventures are incredible! Thanks for taking everyone along! Stay safe!! Jim
@debztully1339
Жыл бұрын
The for the content!
@swedenfrommycam
Жыл бұрын
I have a question about Gedrite in Quartz, is it a indicator around gold? Thanks for all tips and tricks, u make a super channel 😀👍🇸🇪
@tristenshumway6999
Жыл бұрын
Love watching your videos and wish I had your job!! I've always loved working underground and with dirt and rocks, heavy equipment/mining.. Thanks for sharing brother much love and respect from Colorado!
@iknklst
Жыл бұрын
What's involved in moving ore samples across the border?
@jonsdigs1
Жыл бұрын
I just tell them I've been collecting rocks and they have never given me grief.
@Alondro77
Жыл бұрын
Oh yes, I have indeed seen a rusted pyrite vein like this in a remote mountainside in northern NJ where a small landslide at least a century or two ago exposed fresh rock... heh heh heh. Now to get some samples!
@hardrockuniversity7283
Жыл бұрын
I have some very hard and tough quartz also. I use two insert carbide bits from Sierra Blaster because they are both economical and good quality. Even then they only go about 3-5 inches each before dulling. The best method I have found so far is to have a bunch of bits, change every7 seconds, and have a disc grinder to re-shape the carbide inserts when they get dull. I am a bit clumsy, but I can still re-sharpen a bit satisfactorily by eye in about thirty seconds. As soon as a bit starts getting dull, take it out of the rotation and re-sharpen when you have enough dull buts to make it worthwhile. In exploration, a dozen bits weighs less than a grinder. Keith
@bearpump
Жыл бұрын
Jason, kind of a personal question, but how tall are you? It would put some of these tunnels in perspective. Thanks! Jeff
@dustinjohnson3463
Жыл бұрын
Try bentonite clay on the bits to keep them lubed up
@williamries5165
Жыл бұрын
My Name is William. Ries I have viewed. Many of your videos over a couple of years you have done very well to produce excellent videos easy to follow I have done much the same as you in processing assorted ores I love mining and your ways of getting the job done thank you for presenting them
@micphoenix8200
Жыл бұрын
More of this sort of content please.
@SenorQuichotte
Жыл бұрын
You're probably drilling into something like hardened iron, maybe a high speed drill bit not a masonary bit.
@stevekaminski4859
Жыл бұрын
Try Hilti Tools SDS Hammer Drills. They cut into concrete way faster then your Milwaukee or Dan's Makita. I would expect the same for weird rocks too
@dimityrivanov3180
Жыл бұрын
Super nice looking stuffa Jason! Cant wait to see them crusehes... But maaaannn you might even get sulfides in number 1 :D I wish you to hit like 112 ounces per ton from that ore!
@jbowerman50
Жыл бұрын
I used to have to drill concrete to repair door systems, used a Bosch SDS , the Crete was easy, but if you hit aggregate you have lube the bit. Othwise the bit ends up looking like the ones you smoked. Water, best lube for bit to stone. Even then you have to keep changing them so they don't get too warm. And I had to finish more than one hole (because I ran out of bits) with a star drill and 2 pound sledge.
@rubroken
Жыл бұрын
A couple of questions, I just subscribed so these may be covered in other videos. Do you carry an oxygen/gas meter on you? My whole career I worked in enclosed spaces and occasionally ran into "dead" air or explosive gas and know those hazards. Also do you research and find out if these abandoned mines are truly abandoned or just not being worked?
@JoeyFranko
Жыл бұрын
I use to pan for gold in California. I was in the middle of nowhere in the Sonora forest. We noticed a red bandanna in the bushes when we pulled in, didn’t think much about it. About a hour goes by, we are surrounded by 5 Latino guys wearing a lot of red. They were digging something up in the bushes. I kept my hand in my pocket like I might be armed. Of course no one is but the bad guys in California. We loaded up quickly and took off in 4x4. It was muddy and these bozos drove a car down there. They were screaming for help as we burned rubber out of there. I applied for a concealed carry license and of course was denied. So I moved to Oklahoma and got my ccw, but no gold in Oklahoma. Like your show thanks
@carbonstar9091
Жыл бұрын
The end of those bits look like they got very very warm.
@paullong4471
Жыл бұрын
Shalom.Mr.Jason. May i wish you A Happy New Year And Blessed Year 2023 together with your family members and friends..God Bless.Amen.
@n8r8ts41
Жыл бұрын
Diamond coating is definitely your friend. They make very good impregnated products now. Quartz countertop installers know what I'm talking about. You can find local suppliers for bits of all sizes
@keithrimmer3
Жыл бұрын
Jason that ore sure looks like Wolfrom, I would try Hilte bits they do them for concrete and rebar and very hard wearing
@ThunderBird80085
Жыл бұрын
There's probably a carbide insert drill bit you could find that would have better cutting power. You'd also be able to change the tip out on the spot so you'd only need one bit and a bunch of inserts. Like others have said keeping it wet would be helpful as every time I have drilled something with a high hardness a cutting fluid is necessary to not blowing out the tool. I don't know if they exist but if there is a small version of a rock driller with a drill bit that has integrated fluid supply into the end of the bit that would probably be your best tool.
@TrickyDickyP
Жыл бұрын
Jason. Keep us upto date on the processing as i have exactly the same looking stuff as you showed in the video. I would be interested to see what you get.. 😊
@rocktruckrob
Жыл бұрын
Jason hello found you from Dan hurd’s videos… quick question there are old mica mines near me but there is so much quartz in the tailings piles… is there gold near mica or not thanks from deep river Ontario Canada
@geraldbrunckhorst8291
Жыл бұрын
Jason- I’ve learned so much about natural materials in rocks, particularly good showings in quartz veins and in mines. Thank you! Much of my past recreation has revolved around backcountry mountaineering and rock climbing so rock is in my blood. I’ve come to realize how many great veins I’ve crossed and climbed on over the years. Now it’s time to go test some of the more accessible places locked in my memory. Kelp up these amazing videos!!! Thanks Again! Godspeed.
@mikesherman8590
Жыл бұрын
Great comments I let the rotor hammer bounce by very gently just barely touched the rock and then it starts bouncing and it fractures for me it works fairly good.
@roneldridge7991
Жыл бұрын
Yes I do! You need more bits, drill for a bit then change bits let it cool down ! Never let tip get hot you will melt all no matter how expensive. I usually us several bits letting all have chance to cool before I come back to it. I drill Rhodonite from my mine and went through a lot of bits before I learned. Once your tip has been compromised by heat it’s all over. I usually drill 12 holes 18 inches deep in gem grade Rhodonite then pour my dexipan. 13:18
@kensmith8832
Жыл бұрын
It is too bad that you don't separate the metals and show the complete mineral deposit. I hate to see lead being wasted. You make some great videos! The longer shaker table ones put me to sleep really fast.
@chrisstrobel3439
Жыл бұрын
Dreamin the dream man 👍 What a ya do for Grizzly/Blackie/Cougar protection up there? Really enjoy the channel 🤠
@ARGONUAT
Жыл бұрын
By golly I would love to buy those ore chunks as is (was). Such fascinating stuff with an interesting pedigree.
@jerrys1375
Жыл бұрын
I would love to see a livestream with you and Jeff Williams. Good stuff!
@johnsimpson3240
Жыл бұрын
I grew up in a town called mineville in Upstate New York. The mines were and are the source of the purest iron in the world. They are closed now, but the deposit was created billions of years ago when an iron asteroid several miles wide hit the planet. Over the ages, plate tectonics moving the continents around forced that asteroid to the surface. The miners used diamond tipped water cooled drill bits to drill into the stuff because carbide just doesn't do the job. The old timers used to say that gold rides an iron horse, so I think you're drilling into a band of iron.
@jG-dt8vx
Жыл бұрын
you’re drilling through sulfates like you said which are primarily iron or metal with a masonry or stone bit. you need a specialty but that will not get burned up. drilling into metal with a masonry bit will burn your bit up in seconds . just like when the concrete bit hits angle iron a few times good and the tip will be done. wood will burn up masonry bits just as fast. use a different bit for the heavy sulfide material.
@dionh70
Жыл бұрын
With that vein, you're not really drilling into quartz, you're effectively drilling into metal, which is why you're burning up your bits. I used to install all kinds of low voltage systems, such as CCTV, access control (card readers), alarm, intercom, what have you, and mounting stuff on the exterior of buildings often required drilling through concrete walls with rebar. I would use diamond-coated hole saws for anything over 3/8inch, because I got tired of burning up SDS carbide-tipped hammer bits against rebar. And cutting oil was also essential, although I had a shallow plastic bowl that I would dip my bit in to keep mess to a minimum after a facility manager lost his mind over oil dripping out of the hole and staining the concrete.
@WheezinGeezerTV
Жыл бұрын
Awesome looking stuff. Can't wait to see it crushed up and running on the table.
@Addh0le
Жыл бұрын
I saw a bunch of sparks when you were drilling and those bits don't work the greatest in hard metals. Light pressure and some sort of lubricant/coolant would keep it from burning up but it'll take a while. Diamond grit hole saws are really amazing but you have to constantly break out the core to go deeper would also be neat to see the little cores you'd also need some extensions and a little spray bottle of water.
@damic.489
Жыл бұрын
hi, for the drilling process, take a bottle of water and a water spray bottle. Drill for 5 seconds and spray water in the hole and repeat the process. That way you won't burn the drill bit. Carry some spare batteries.
@silvaorgold
Жыл бұрын
Why man that looks really great I bet you wish you could pull out more than just a couple bags that heavy sulfide stuff I can't wait to see what it crushes up and looks like thanks for the great video looking forward to the next
@jimmime
Жыл бұрын
Follow, follow, follow that yellow brick road! Thanks, Jason.
@LandscaperLife
Жыл бұрын
I know absolutely nothing about mining, but I do have some experience with hammer drills. Is it possible that the pressure from the mountain above is making it harder to drill? I would poop my pants drilling into those columns lol. Great video as always!
@IMKINDOFABIGDEAL13
Жыл бұрын
I don’t need any special circumstances to poop my pants lol
@LandscaperLife
Жыл бұрын
@@IMKINDOFABIGDEAL13 🤣
@johnwilliams8818
Жыл бұрын
😇 Try some WD40 🤣 That stuff seems to work for pretty much every problem.
@bioniclife
Жыл бұрын
Neat channel, neat video. My profession has allowed me to be underground in a few different mines. The Barrick Williams mine in Hemlo stood out since I was a mile underground and we went into a few areas that were pitch dark. Subscribed!
@tuvoca825
Жыл бұрын
So comforting until...
@TheOleowl
Жыл бұрын
Hi Jason. Amateur Al here. I have a thought for ya on those bits you tried on this video. Those bits appear to be stone/ tile, concrete bits. If your ore is so metalic as it seems to be why not try using a hi grade steel bit? Just a thought. Great show.
@dionh70
Жыл бұрын
Flora is vegetation, fauna is wildlife. I remember by equating flora to flower, and fauna to a baby deer/fawn.
@shermdeazy
Жыл бұрын
Can you use harmonic frequency to soften the quartz before drilling?
@trevorwhat
Жыл бұрын
Hi Jason, I’ve had success with Bosch carbide bits in quartz.
@Stevesbe
Жыл бұрын
He's drilling metal
@trevorwhat
Жыл бұрын
@@Stevesbe yes, I should have included sulfides, too.
@11regnartseht
Жыл бұрын
@@Stevesbe sulphides have metal in them but they are not metal and don't have the same physical properties.
@trevorwhat
Жыл бұрын
@@11regnartseht that’s right. And although the two “metallic” samples Jason was holding looked to be massive and semi massive pyrite, because it’s slightly softer than quartz (Mohs ~ 6.5 vs. 7.0 for quartz), the Bosch bit should work if it’s semi lubricated. I’ve had no issue drilling through quartz and pyrite in the same holes. Caveat: I’ve never used it all day; maybe a max of 10 holes in one session.
@jasonharper2601
Жыл бұрын
diable makes a great bit. i have used them making anchor holes in rock, concrete long-lasting
@dillonlee6145
Жыл бұрын
I'm excited for tomorrow
@kencarbon2346
Жыл бұрын
Enjoyed watching your video thankyou for sharing your experience and information with us.😀
@wilsonrawlin8547
Жыл бұрын
Looks like Silver to me. Great find and you work your tail off brother.
@mattnelson4387
Жыл бұрын
That looks so fun. Very informative. Wish i still lived in the pac NW. What size drill do you use in that hammer drill?
@josegalopez
Жыл бұрын
I work in the rail industry, and part of that is drilling holes in the rails. We use a product called Lubrisol which we mix with water until it's the consistency of milk. Put that in a pressurized weed sprayer and you'll save on your bits. Love the vids!
@josephcormier5974
Жыл бұрын
This looks like it's a viable mine let's hope that your essay is full of gold and silver thanks Jason six stars brother
@JimFinlayson
Жыл бұрын
Hopefully Milwaukee will sponsor you, you deserve it.
@johnnywadd9918
Жыл бұрын
Rebar eaters may work better with all that metal content in the rock. Add cutting oil or water to keep bit cool
@melvinroehm821
Жыл бұрын
Wow.nice vein..hopefully it's got good gold locked up in it
@chadgretzner
Жыл бұрын
The bits may have become dull and may need to be sharpened or simply replaced. There are other great suggestions as keeping the drill steel cool and rotating them out during drilling.
@timv453
Жыл бұрын
I don't think I can go into those mines, the vicarious experience is amazing. Thank you for your efforts.
@dionh70
Жыл бұрын
I'm mildly claustrophobic, so my ass will NEVER go into those tight spaces. Not even gonna apologize to anyone about that.
@billoc1255
Жыл бұрын
Looking forward to you processing!
@ubermachtthemechanic007
Жыл бұрын
I'd try attacking the host rock above or below the sulfide vein. I'm thinking the metals in the vein are killing the bits. In any event, I'm so envious watching Jason so this stuff! Getting my life to a point where I can do this would be a miner miracle! (Get it... miner/minor... sorry total dad joke...)
@danielmanning2107
Жыл бұрын
cant wait to see what you found. that is so cool. i like Dan Hurd's and your videos the best on youtube. keep them coming.
@Oldmane-420
Жыл бұрын
Have you checked out Vogus Prospecting channel. He’s an Aussie with a sense of humour and he is prospecting various placer and old hard rock mines for undiscovered and left over gold. He is amature status compared to the equipment being used by Dan and Jason, but still very interesting nonetheless.
@frozenjoe6313
Жыл бұрын
Makes me wonder how the old timers mined through that material in the mine the first time.
@rikspector
Жыл бұрын
Jason, That was an awesome site, I hope it’s a winner! Cheers, Rik
@michealklonowski5267
Жыл бұрын
thank you for sharing the adventure 😀
@LOSTMINERSGOLD
Жыл бұрын
Great video Jason, I always learn something. Try using a cutting oil if hitting metal on metal it cools the bit and they seem to last longer. Hope to see what your samples shows. Heavy pans to you.
@daz41262010
Жыл бұрын
great video Jason :) I can't wait to see the results bro :)
@FjHenderson
Жыл бұрын
Very interesting, cantwait for the outcome 👍
@richardjay9757
Жыл бұрын
All I can say about the drill bits is I have a chunk of ore that's solid sulfides about the size of a basketball and I've attempted to split it open with feather and wedges...it burnt up all my drill bits also on 1 hole
@bearbait2221
Жыл бұрын
burn the quarts chunks in a camp fire it will crumble after that.
@richardjay9757
Жыл бұрын
@@bearbait2221 I plan on doing just that...I was gonna quench it right after burning it...I crushed and smelted a small piece with some flux and I got a 2.1 gram bead of silver colored metal out of it!
@bearbait2221
Жыл бұрын
@@richardjay9757 nice! Im an Alaskan prospector i normally hunt alluvial gravels but i have found 6 and 8 foot wide quarts veins that i now have to test them only winter stops the fun. i have e few more mouths of waiting so i gold mine on youtube lol
@dodgeit3014
Жыл бұрын
Good stuff man. Looked sketchy for sure.
@jimwednt1229
Жыл бұрын
I want to see how you'd open up a portal into a fresh vein . How to tell, by whatever means necessary, where it's a good place to mine ore . This is another good video anyway. Good work , I look forward to seeing the assays on the ore you pulled out of there !
@billhollinshead
Жыл бұрын
0:53 Nice view of foot-wide brecciated zones within the vein. Some of the sulfides looked like like arsenopyrite - did they smell like garlic when struck?
@TheMorbidMagpie
Жыл бұрын
Since it’s very metal heavy rock, I would try a metal drill bit as it’s worth a try, just some cheap bits to see what happens, also a spray bottle to spray your bits while drilling to cool them down a touch
@dusanholak9560
Жыл бұрын
☢️☢️☢️☢️☢️☢️☢️☢️☢️☢️☢️🚀🚀🚀🚀🚀🚀🚀🚀🚀🇺🇲🇺🇲
@NOFX0890
Жыл бұрын
Awesome man. Cant wait to see you process it.
@stupidminotaur9735
Жыл бұрын
Dan's feather and wedge's. once agian.
@oswynfaux
Жыл бұрын
Always good to recheck what the old timers were interested in
@idiggold
Жыл бұрын
That vein looks yum.
@hardrockuniversity7283
Жыл бұрын
BTW, I only carry a 2 lb hammer for sampling. A lot more power.
@devinreed2003
Жыл бұрын
Fascinating stuff i enjoy your content
@GSProspecting
Жыл бұрын
What a blast coming by. Keep on having fun and living the dream fam . Gold Squad Out!!!
@frozenjoe6313
Жыл бұрын
You have so much knowledge and practice I hesitate to say much. However I have done some drilling for the same stuff you are doing right now. . Rock capping. Quartz and other country rock are very hard, and doesn't get much harder Try using a 1/4 inch bit, and build a rock capping kit, like I did, making sure you have 2 or 3 layers of good shielding material and matting to protect your eyes and everything else. Even with the heaviest hammer drill harbor freight makes, that plugs into 110 volt . Its hard hitting drilling and even the best bits you can buy wear quickly on that quartz. I also have a modified ramset powder actuated anchor gun that will drive anchors through 3/8 " steel, and rock and there are larger old time Ramset type powder fasteners type that go up to .38 caliber used for shipyard steel hull repairs for temporary hull patches and those are even more powerful and dangerous of course. But they work.. I might let you use my set up, I built ,, Bearing in mind even the heaviest, hardest steel anchor Fastenal makes could turn and come flying back at you, if fired into rock , causing death or injury if fired into quartz or country rock just 1 time. so I like and use sandbags.,,a lot.,,,,,,,,,,, maybe we can talk about that.. Please P.M. me.
Пікірлер: 451