I like your idea to mark the tie rod flats, and the arrow. Going to start using that on the SM cars I work on!
@MixTureVidz08
9 жыл бұрын
Should do one for NA. Since NB have one shier, NA have two. GREAT VIDEO THOUGH, GREAT PRODUCT!
@DANAMERICAX
10 жыл бұрын
Very helpful, I think my end links are proper but I'll have to check them again now that I've watched this.
@mrmazda329
10 жыл бұрын
Just installed these. Very high quality product. Correction the video tho. The Stock MSM front bar has built in anti-walk collars but the stock MSM rear bar does not.
@NikoWheels
9 жыл бұрын
Wondering how the average joe is supposed to get full load on the suspension like that. Is it possible to have whoever is corner balancing our car to adjust the end links?
@GR44N
3 жыл бұрын
First question: The average joe can use ramps. Second question: Anything is possible, depending on what you're willing to do for it lol
@dielaughing73
Ай бұрын
It's possible to fine-tune the turnbuckles with the car on its wheels: Set them with no pre-load on jack stands but don't tighten the locknuts, then fit the wheels and lower the car. Snake your arm in and check the adjusters are still turning freely (should be able to find that 'dead spot' fairly easily by turning it with your fingers). Then Jack the car up again and tighten everything, knowing it's properly adjusted. Don't be tempted to try to tighten it all down without jacking the car up again - there's not enough access and you're likely to round something off or not tighten consistently
@ricepony33
10 жыл бұрын
Great timing on this! Where do you get those spacers you are mentioning?
@GR44N
3 жыл бұрын
Those come with the end links when you purchase them from 949 racing
@WhiteFeatherGaming707
5 жыл бұрын
This is confusing for na guys and your included directions say to put the spacers on the sway bar end but you show in the video the spacers on the control arm..?
@949RacingSuperMiata
5 жыл бұрын
Either way works. Goal is to have links as close to 90° to bar when car is on the ground. Not always possible to get that angle but you try to get as close as you can with your particular bar and ride height. Don't over think it :)
@haeuk
8 жыл бұрын
Question to 949 Racing! So purchasing a set of end links is just for property install aftermarket anti-sway bars ?(in the situation of the new one has different size to OEM)
@GR44N
3 жыл бұрын
Even the smartest people at 949 can't decipher what in the world you're trying to ask bruh.... try again, this time check auto-correct.
@949RacingSuperMiata
10 жыл бұрын
Andre, Googles wonky updates for YT won't allow me to reply inline. Parts available on our website.
@ddizon666
8 жыл бұрын
thank mate i got mind today from australia
@oscarlainz
4 жыл бұрын
How did you mount those rear brake ducts? Thank you from Spain!
@GR44N
3 жыл бұрын
He mounted the brake ducts using the instructions provided with the kit when you purchase it.
@oscarlainz
3 жыл бұрын
@@GR44N there is no kit for the rear … smart ass
@ddizon666
8 жыл бұрын
can i put wheel bearing greased
@henryliu8518
4 жыл бұрын
Hi, what's the torque spec for the mounting bolts? Thanks
@GR44N
3 жыл бұрын
The answer to this question is 34-39 ft lbs, of course google would have given you a quicker answer than mine 1 year later. I hope your car isn't still waiting to get these installed lol
Пікірлер: 25