Thanks for shairing your experiments. I am in the process of trying to increase the depth of my Surf PI 1.2. My first coil gets about four inches in the air. Doesn't matter what the metal is, all seem to register the same. Gold included.
@eversite
2 жыл бұрын
Nice Spiral Coil :D
@unimike9211
8 жыл бұрын
Could you show precisely how the basket winding is done from the begining, for those of us who are newbees? Thanks
@itakeyourphoto
9 жыл бұрын
For a pulse induction detector coil you should use stranded wire not single magnet wire! Magnet wire is the worse wire you can use, Best wire to use is Litz wire, Stranded Teflon coated wire is the second best., Regular PVC covered stranded wire being third the best. If your detector is aimed at small gold and can sample fast then you have to shield it as well and that's best done with Mylar strips after you put some PTFE spiral wrap around the coil first to provide a spacer between the windings and the shield. You MUST leave a gap in the Mylar wrap usually near were the wires come off the coil otherwise you will loose sensitivity. I would shield any PI coil, Make a coil as above and get the resistance and the inductance right as per your detector design spec and you will see a big difference! Also once your coil is working good adjust the damping resistor value in your detector as you will find you will be able to use a higher value than what was suggested in your detector design and that will increase sensitivity as well. All the above apply to fast sampling detectors like the minipulse plus but works equally well on the surf pi If you try to make a coil for a commercial PI detector like the minelabs using magnet wire they wont work at all! Hope this helps and good luck with your finds!
@sierraridgereaper
5 жыл бұрын
You failed to mention that there are hundreds of sizes of litz wire and failed to mention there is a right and wrong way to apply mylar as well.. 250/46 dual sleeve layered litz is the highest you want to use and 175/46 single sleeve layer is the lowest you want. Both work very well but the 250/46 dual layer works best. With mylar, there are 2 sides, one side beung conductive, the other side not. You want the conductive side away from the coil windings. You can verify which side is which using your ohm meter... Also, a bundle wound solid wire coil is not always bad. Out of over a dozen detectors built, a few of them work best with single strand copper wire 24 to 26 awg. It all depends on the tuning of the detector. If your building it without a scope, good luck getting any kind of decent depth or sensitivity. You need to fine tune using a scope for best performance, especially your tx pulse width and delay widths along with tuning for best damping resistor. Also, shielding a coil in most instances, mono especially, you will lose depth and sensitivity.
@MrJkosta
3 жыл бұрын
Did you wrap that 2nd winding parallel to the base coil or sort of at right angles to it?
@kenny444tourist4
9 жыл бұрын
when you added the second winding, did you try swapping the wires over? A-A & B-B failed but will A-B & B-A work?.
@cwarrillow
9 жыл бұрын
Yes I experimeted, works the same either way round
@kenny444tourist4
9 жыл бұрын
OK. Please keep giving us info, thanks.
@patprop74
8 жыл бұрын
Would it be possible that the extra wrapping simply made the coil tighter hens, giving it better inductance ?
@JoaoBatista-xy3us
Ай бұрын
Por favor me manda a lista das peças para eu tentar montar um detector
@sales4me24
8 жыл бұрын
Detec, did you use a damping resistor with this basket coil at all? I have that same PI kit and am looking for the best coil that is easier to make, i have made a simple mono coil. with that i only get about 2" in a air test. I think the basket coil is the simplest way to go without going with a DD coil. I want to start with something simple to use the detector before i start trying to make if more efficient
@tuco5739
7 жыл бұрын
Detect what was the basket coil inductance? 250uH I think you said? what about the impedance? in ohms. Great video and I appreciate you sharingCheers!
@budiparwanu1992
4 жыл бұрын
I like it's.. but.. How make for coil... Turn? Email mm? Diametre inch? Thank you.. 👌🏻👍🏻👍🏻🙏🏻
@OG96932
9 жыл бұрын
nice video, ive always wrapped my mono coil in silver foil and insulated in electrical tape, and found it slightly gives greater depth, when testing on the surf pi. i wonder, if wrapping more copper around the coil, which you have demonstrated gives greater depth, but what if you increased a few more wrappings, say another 2 wrappings, will it make any difference or better the depth even more? cheers
@cwarrillow
9 жыл бұрын
Im goin to try the extra turns on the larger basket coil Im making now.
@cwarrillow
9 жыл бұрын
The new bigger coil I made is even better than the smaller version. But wouldnt work well with the extra winding.
@Patrick97123
9 жыл бұрын
Thank you for sharing..Where would I find the basket coil form?
@cwarrillow
9 жыл бұрын
I made my own
@negoitasoringabriel6929
9 жыл бұрын
Where have you bought the kit from?
@qwertyraefay8663
8 жыл бұрын
thanks vry good
@hughh106
7 жыл бұрын
The wire wrapped around might by acting as a Faraday cage
@hughh106
7 жыл бұрын
One way to make this is wrap foil around the coil
@ahmadsoleh69
6 жыл бұрын
wat all original ic.......
@henrychristian6825
9 жыл бұрын
The sound is lousy plus you and whomever is with you talk over each other so bad that I can't understand you.
@unimike9211
8 жыл бұрын
+Henry Christian How ungrateful can you get ?? People go to the trouble of giving up their time and knowledge for the benefit of others, and all they get is this sort of abuse.
@sierraridgereaper
5 жыл бұрын
The hec you talkin about? Volume was good and there is only one person talkin in the whole video... those voices in yer head are screwin with ya...
Пікірлер: 27