Hi this is the one of the most valuable M16A video I've watched!! Thanks so much!!
@piotr12031987
3 жыл бұрын
dobra robota!
@suzukiracingcup
3 жыл бұрын
Good engine!
@wilsonwei9604
Жыл бұрын
Hi just come and say thank you again I fixed my M16a and it runs smooth and great. Thank you for your videos!!
@ssss-df5qz
10 ай бұрын
Did you have a bouncy idle?
@wilsonwei9604
10 ай бұрын
@@ssss-df5qz not at all, smooth like butter
@ssss-df5qz
10 ай бұрын
@@wilsonwei9604 ahh man, mine is bouncing slightly
@WillardRoberts-cy3nz
Ай бұрын
Thank you very much
@PURERAYN
Ай бұрын
2 bolts were left out from the main bearings cap
@cordoba212
2 жыл бұрын
mega
@ssss-df5qz
10 ай бұрын
Have rev hunting on a 2012 1.6 swift sport. Do these chains stretch? Can hear a very faint chain noise by where the phaser is.
@shoiabmulla7426
Жыл бұрын
How much is torque setting for cam shaft bearing cap
@alonsoelectro1052
Жыл бұрын
Felicidades desde 🇵🇦
@misch2
2 жыл бұрын
Isn't there a pair of bolts missing (for example @24:00) near the 3rd valve set? I mean there are 4 pairs of black bolts but only 3 pairs of "silver" ones (while the holes are there).
@hex3stuff207
2 жыл бұрын
there is no factory thread in the engine block at this point. but a big plus for attention
@misch2
2 жыл бұрын
@@hex3stuff207 Wow, interesting, thanks for the explanation. Now I am not worried about the engine anymore :-D.
@wilsonwei9604
2 жыл бұрын
hi may I know how you adjust timing chain and TDC? For example, which one do first? and after doing one of them, how to make sure when I turn to the right TDC, chain is okay? I've been reading manual and watching video but can't figure it out.. Thank you!!
@hex3stuff207
2 жыл бұрын
Hi, in this engine the timing pulleys are "fixed", the so-called wedge, so set them on the marks that are on the wheels. The timing chain has links in other colors. please let me know if I understand the question correctly?
@wilsonwei9604
2 жыл бұрын
@@hex3stuff207 Hi really thankful that I can get your reply!! I mean 1. should TDC been set up before the timing chain? 2. or, when fully setting the engine chain timing and start turning it to get the right TDC, this moment, we have to have both TDC and timing on the right spot? Cause when I was watching your video, I saw you put a stick in it and turned the shaft to get the highest point (TDC right?). I wasn't too sure the timing marks were on spot at the same time or not when TDC was done. Again thank you for your replying!! Kind regards
@hex3stuff207
2 жыл бұрын
@@wilsonwei9604 1. set the piston a little before tdc so that there is no collision when setting the shafts. we set the shafts so that the characters are \ / to the plane of the head as in the video. then we put the shaft in tdc and the chain can be set up. 2. I did not understand the question. after setting the timing gear on the markers, point 1, tighten it with the tensioner, then make a few turns and set the tdc with a stick to check if the original position camshaft of the is exactly in place as in point 1.
@pawewilamowski9680
Жыл бұрын
Hej dasz do siebie jakiegos maila? bo mam pytanie odnosnie mojego swifta i dziwnego dzwieku na zimnym silniku
@MrDingaling007
2 жыл бұрын
Any idea what the headbolt torque value is for this motor? Cant find much on the internet...
@RGV2300
Жыл бұрын
There is a lot of suzuki, japanese cars are well covered. My favourite site is cardiagn.com.
@pedrobanzainunes8851
4 ай бұрын
No gasket???🤔🤔🤔 No sealant???🤔🤔🤔
@alleyek
3 жыл бұрын
Gdzie cześć trzecia? ;)
@WillardRoberts-cy3nz
Ай бұрын
In the timing cover there is plug what it call
@darekfatua8631
3 жыл бұрын
Jaki jest koszt wymiany łańcucha rozrzadu ? Czesci z robcizna
@hex3stuff207
3 жыл бұрын
Wszystko zależy jakiej firmy rozrząd. Średnia półka skf okolo 550 wymiana okolo 450
@sebastianortiz9743
6 ай бұрын
Hola tienes las medidas de apriete de la culata (cabezote) cigüeñal y bancada
@hasankaradeniz8007
2 жыл бұрын
Orta grank kepin 8mm civatalarını takmayı unuttun sınıfta kaldın
Пікірлер: 31