In my experience Alibaba customer service is 10 times better than any local company in the US. In my opinion, they seem to be more knowledgeable too
@djr96
3 ай бұрын
Yes it is because there is no correct manual available.
@djr96
3 ай бұрын
I have szgh 1000 mdcb and I am following 4 manual of different versions how pathetic.
@user-of8ve4gi6c
2 ай бұрын
@@djr96вам удалось настроить систему для работы? Я хочу купить подобный контроллер, но есть сомнения, что смогу самостоятельно настроить следуя только инструкции
@NEWKerCNCTECHNOLOGYCOLTD
3 жыл бұрын
Thanks for choosing and using our product, we are the manufacture, if need any help, please let us know.
@passenger6735
Жыл бұрын
I have one of these systems on my lathe. I love it but why does it keep defaulting to G53? Can I change the default to G54?
@NEWKerCNCTECHNOLOGYCOLTD
Жыл бұрын
@@passenger6735 thanks for using NEWker controller, you can use MDI to run G54 to swtich the coordinate system, or you also can add G54 in your program.
@passenger6735
Жыл бұрын
@@NEWKerCNCTECHNOLOGYCOLTD I do use G54 in MDI and I do insert G54 in a program however if the machine is switched off it defaults to G53 which is not what I want. Is there any way to change this default value?
@NEWKerCNCTECHNOLOGYCOLTD
Жыл бұрын
@@passenger6735 oh, sorry that maybe your controller is too old version, our newest version could save the coordinate status, if you are interested, please contact with your supplier for purchasing newest version controller
@mutluoglumakina971
Жыл бұрын
thank you very much
@forcedflow8567
9 ай бұрын
Hey Dean sorry to bother you can you tell me what size flange are the servo motor it looks like 150mm and shaft sice? Thanks
@hemsworthlad
9 ай бұрын
Flange 130mm with 110mm boss and 22mm shaft size 57mm length 6mm keyway
@harindugamlath
3 жыл бұрын
How's your system going? Did you finish the project? How is the reliability?
@MartinKl87
3 жыл бұрын
Hey, i have the same problem with the controller. which settings do I have to change ?
@tgimagineer505
4 жыл бұрын
Dean, I have tried to use the Hand box with the Panel pulse generator and they seem to interfere with each other. Also the parameters have to be set for one or the other. I would love to see if you have a different result, because I would like to use them together. Rich
@newkercncnandylee7889
Жыл бұрын
Other parameter #1, Used to set if installed with hand wheel, 1 means handhold, 0 means panel.
@sobelsonski
3 жыл бұрын
We have same and have big problems with it. Every restart coordinates change, from company said we have to do initial encoders debuging but cant explain us how exactly to do it. Any help will be highly appreciated.
@MartinKl87
3 жыл бұрын
did you have solve the problem? email me martin.kleinmans@gmail.com
@dabooge
11 ай бұрын
Hi Dean, did you purchase directly from the company or through their store on aliexpress? I'm contemplating buying their lathe controller
@hemsworthlad
11 ай бұрын
First contact was through AliExpress but pretty much same thing I think. They are very helpful and support was second to none, and still is 2yrs later, only other day asked a question and got a reply within 3hrs.
@uptechcncpvclt-1302
Жыл бұрын
i have the same controler, i bought direct from factory but i have a problem that the axis rotating in one direction , do you know whats the problem is?
@rmorr01
3 жыл бұрын
Hey Dean, Can you tell us if the controller can be set up for (imperial) inch units?
@hemsworthlad
3 жыл бұрын
Yes it can
@rmorr01
3 жыл бұрын
Yes, go into MDI mode then type= G20, hit cycle start and your controller switches over to inches including your DRO's. Example: from X1.000 to X1.0000 > The same goes for Metric (default) same thing but G21 and your back in mm.
@djr96
3 ай бұрын
Does absolute servo need axis limit swtich .???
@hemsworthlad
3 ай бұрын
No you can set travel limits. It knows axis location and won't allow travel past what's set.
@djr96
3 ай бұрын
Thank you friend@@hemsworthlad
@djr96
3 ай бұрын
Don't understand (travel past what set)
@djr96
3 ай бұрын
And I watched you videos completely . But unable to found any solution.
@djr96
3 ай бұрын
In my case when set servo zero position at machine datum .after power on off the automatically show +2mm even if physical machine doesn't move a bit. Why this is happening can you help in this.
@vanwyksc1
4 жыл бұрын
Do you have the Password for me so that I can make backups of parameters and ladder before I loos it?
@hemsworthlad
4 жыл бұрын
111111 OR 666666
@berndloos7903
3 жыл бұрын
@@hemsworthlad mine was 12345
@steveu235
3 жыл бұрын
is incremental system same as open loop or close loop
@hemsworthlad
3 жыл бұрын
No, incremental just describes the type of encoder that is used for feedback to the drive. An Open-loop system doesn't use any feedback.
@m3chanist
3 жыл бұрын
The GUI design is crap, the enter esc combo on screen is in the reverse order to the ones on the physical pad. Id be pissed off with whoever designed that UI. It visually programmed you to fail.
Пікірлер: 38