Thanks for the updates and that you’re happy with support from SZGH. I’ve exchanged many emails to get everything organised, Making payment for full system tomorrow. I’d be keen to see some more info on how you wired it up. Looks like you went for 220v drives. I’m requesting 380v drives and hope it’s the right choice
@steveu235
3 жыл бұрын
Hi Dean Thanks for the videos I'm a machinist no electronics training. I've made a cnc plasma table using Mach3 and Longs motor and breakout board set it works well, Now I'm trying to convert an old TOS vertical milling machine to CNC I'm interested in buying one of the controllers but am a little weary of spending 1500$ on something that may be way to complicated for me to set up. Could you tell me if this controller connects to a breakout board or do all the motors connect directly to the controller? Thanks
@jhonh3983
3 жыл бұрын
hi, what encoder can i use to control the spindle? Thank you
@berndloos7903
4 жыл бұрын
been working on my system 1000 Mc now for about 2 months, using teco drives and motors cant seem to get the motors to move ! ive had to use a 50 pin breakout board to to connect to the 15 DB cable , but nothing but lockup of the servos and no movements. What drives and servos did you use?
@hemsworthlad
4 жыл бұрын
I used Servos and Motors from SZGH but that shouldn't matter. If the drives are enabled and the motors Lock up and you have connected to the correct Output signals they should work regardless of what drives/motors. Are your drives Step n Dir or Analog +/-10v and if they can be used with both like many do are the drives to correct Mode.?
@berndloos7903
4 жыл бұрын
@@hemsworthlad step and direction ! they have responded twice with pin outs from the controller and no movement! they are teco tsta drives and 750 w motors from machmotion ,got the motors moving with the driver control panel but not the szgh controller!
@hemsworthlad
4 жыл бұрын
@@berndloos7903 Have you connected the input Di-1 to IG24 to Enable the Servo. Also, have you set parameter Cn001=2 so the drive is expecting an external pulse command.?
@berndloos7903
4 жыл бұрын
@@hemsworthlad I WAS JUST READING THE Cn001 =2, I will have to check, thanks for the rapid responce ! will have to power up the controller tomorrow
@berndloos7903
3 жыл бұрын
@@hemsworthlad Well that did the trick! in MPG the servos travel at the same speed forward and reverse, now to figure out why one way in manual (jog) mode all the servos will travel at a normal rate one way then reverse it and its like in rapid mode? any ideas ( I really appriciate your help) reading these CHINGLISH manuals is frustrating!
@mcping
4 жыл бұрын
How's it going ? Im a bit interested in this controller myself for my XYZ560. Looking forward in some new videos :)
@berilselim5449
Жыл бұрын
I've been commissioned, can you give me the other parameters?
@hemsworthlad
Жыл бұрын
Sorry far too many parameters to list. Download the manual they are all listed.
@berilselim5449
Жыл бұрын
@@hemsworthlad thanks
@mxhotta
3 жыл бұрын
good job!! I have to change the plc ladder , but ask for level 2 password szgh support staff doesn´t seem to release..do uou know what this password? tks
@mebfab6596
2 жыл бұрын
You ever get this onto a machine?
@hemsworthlad
2 жыл бұрын
Yes, and it works very nice. Also, fit the same absolute controller with 180mm 2.2kw absolute servos on a Hurco BM40. Both work great and are relatively simple upgrades. SZGH are super helpful when it comes to setting up the controller.
Пікірлер: 19