shop improvements are self satisfying, personal and fun....lots of methods to complete this and you made your choice....nice! ATB
@gareththomson4080
4 жыл бұрын
A nice simple solution to an annoying problem. Great video, thanks
@leriksenbendigo
4 жыл бұрын
Love the Flying Spaghetti Monster shirt
@AlwaysSunnyintheShop
4 жыл бұрын
Thanks! Hi noodly appendages are always with me.
@SolidRockMachineShopInc
4 жыл бұрын
Nice job Aaron! Steve
@mrjohnnydrinkard322
4 жыл бұрын
Thanks for sharing the build, i kept tapping my screen thinking the fade out was my screen's auto shut off.
@TAWPTool
4 жыл бұрын
Great project. Thanks for sharing!
@billstanley4819
4 жыл бұрын
Yea, these are nice covers. Should last forever. I made mine out of Masonite sealed with clear lacquer. Shallow wood trays on left and right sides hold small tools, calipers, etc. two strips of wood on the bottoms keep the trays from accidentally getting knocked off. Cheers!
@DAVE94LIGHTNING
3 жыл бұрын
Very nice. I just designed a set in CAD and 3D printed in ABS. They should hold up pretty well.
@cuttingtooldesigner
4 жыл бұрын
Nice video Aaron. As I was watching I thought of the magnet addition also. Might help with the tendency to slide off to the side. Keep up the good work my friend. Dennis.
@EmmaRitson
4 жыл бұрын
they look good. james is right. wants a groove around it at least to stop things rolling off
@donmittlestaedt1117
4 жыл бұрын
Thank you.
@thomasutley
3 жыл бұрын
Nice job! I like the other suggestions to add a lip. It will catch debris but might save an expensive cutter hitting the floor. Some 1/4” x 1/4” aluminum bar epoxied front and back would save the tools. Leaving it off the left and right ends will let you wipe the covers down without having to remove them.
@tomclark6271
4 жыл бұрын
I'm with Tuna. That stuff cuts fast and super easy on a table saw with a carbide tooth blade. Keeps the glass fibers out of your machine tools.
@AlwaysSunnyintheShop
4 жыл бұрын
Wouldn’t trust myself to cut the contour with a saw, but I guess I could have ripped them down with a saw. Not sure I have a carbide blade or not.
@tunafish3216
4 жыл бұрын
I’ve end milled that stuff before it ruins carbide end mills.
@silverbullet7434
4 жыл бұрын
Look good , that stuff holds up well. Think I'd do like the others and glue some edges on ,should make them more rigid too. I would use a couple magnets underneath.
@kylemichael2175
4 жыл бұрын
Aaron, how did the surface finish come out on the cut edges? Was wondering if there was a sharp edge or a burr. Looks good and seems like a good material for covers. I use 1/8 thick clear rubber I cut for my table. The material was originally used as those clear doorway strips you might see hanging over the doorway at the deli in the grocery store or a butcher shop etc. They work great but I goofed up cutting my last piece, so I need to get more or a different material.
@AlwaysSunnyintheShop
4 жыл бұрын
The edge is actually pretty clean. A little bit of fiberglass fibers sticking out, but not much. And the edge isn’t really sharp, which is unexpected. I suppose some of the resin flakes away and prevents a hard edge. We’ll see how they hold up.
@kenny5174
4 жыл бұрын
I think you need a couple finger holes on ends, to hang them on a hook when not in use.
@bertwacaser6719
4 жыл бұрын
Clean looking covers should serve you well also I'm going to get some of those epoxy packets the syringe type can be some what of a waste.
@bid6413
4 жыл бұрын
Nice project. How about a trim strips around the edges of the covers to keep things from rolling off? I found them helpful on my mill. A last thought, consider cutting the covers into 4 pieces so you can move your vice to either side of your table. Just thoughts. That poor skinless cat. I cannot believe the order and cleanliness of your shop and tools. Amazing.
@chrisstephens6673
4 жыл бұрын
Yes, as made it does encourage all the wear on the leadscrew to be in a very small length. But then machinists do seem to like symmetry.
@RJMachine62
4 жыл бұрын
Funny, yesterday I was thinking I needed to make some covers for my 10x50 mill table. I might be seeing things but It looks like your spindle nut was loose. That is the retainer nut on the bottom of your quill. It looks like it turned some after you turned on you mill. There should be a set screw to hold it after you snug it up.
@mrjohnnydrinkard322
4 жыл бұрын
I had it on my mind as well....the algorithm is on overdrive. Good eye , it is loose
@RJMachine62
4 жыл бұрын
Good video showing what I was talking about. Robin does a great job. kzitem.info/news/bejne/yKiLyqeKjYR4n2k
@AlwaysSunnyintheShop
4 жыл бұрын
I’ve noticed that too but there is no set screw to lock it in place. Just two holes in the bottom face for a pin spanner wrench. The nut moves a few degrees and no more. I’ll have to find a Sharp manual and see if there is a way to lock it, or if this is normal.
@RJMachine62
4 жыл бұрын
@@AlwaysSunnyintheShop My Sharp manual shows a set screw. It's not on the nut itself but if you drop the quill down, the hole should be in the side of the quill near the bottom, maybe 1/2" up or so.
@AlwaysSunnyintheShop
4 жыл бұрын
D’oh! Just a little loose. Tightened it up and measured .005 clearance which is apparently fine. Hopefully no problems will come up because of it.
@sundaynobody
Ай бұрын
great video! where'd you get the material from?
@MegaRiffraff
2 жыл бұрын
👍🏻
@rubarb0406
4 жыл бұрын
Aaron, thank you for sharing. Far superior to a T-slot cleaning tool. . . I do have a question. Is there a reason you did not extend the cover so the gap between the table and the DRO scales was protected? I noticed that close to the vise you had addressed the gap.
@AlwaysSunnyintheShop
4 жыл бұрын
I didn’t want to have these covers overhanging anywhere- too easy for them to catch on my hand as I reach for the vise handle or something and flip them up or just scrape my hand. That foil tape was there when I bought the machine- I need to replace it to cover the full length of the gap, but when I’ve looked at the scale it’s always been clean. You bringing it up makes me want to do it though. Thanks!
@JamesDedmon
4 жыл бұрын
Neat idea, however I’m like a lot of the commentators some sort of lip to hold tools example a spotting drill, drill, chamfering tool and tap, for hole drilling comes to mind. Or I guess you could lay one of the trays you have on top
@kirkshirley1319
4 жыл бұрын
The sintra, xpanded PVC sheets.
@davesalzer3220
4 жыл бұрын
Kinda jenky? I don’t think there’s a more precise way than direct marking like that.
@MrPatdeeee
4 жыл бұрын
Good job. But then all you do is good.
@AlwaysSunnyintheShop
4 жыл бұрын
Thank you for the nice compliment. I try to put in an honest effort in everything I do.
@curtisvonepp4335
4 жыл бұрын
Milling machine table cover's kinda useless your tooling finds its way falling on the floor I'd rather have tooling fall into a T slot where it's safer 😨😁
@AlwaysSunnyintheShop
4 жыл бұрын
Ha well there’s that. I use my little organizer trays for tools so hopefully I don’t miss having the tee slots open.
@tunafish3216
4 жыл бұрын
They have plastic t-slot covers that are cheep you just cut them to how long you want them.
@tunafish3216
4 жыл бұрын
A table saw is faster.
@curtisvonepp4335
4 жыл бұрын
👍 😁 the problem is maybe they don't have a Table saw 😨
Пікірлер: 54