⬇️⬇️ (English translation below the Italian text) ⬇️⬇️
Alcuni liutai la fanno in modo diverso, preferendo un raggio e una curvatura longitudinale fissi invece del raggio e curvature longitudinali composte che io uso. La tastiera funzionerà sempre, ma sarà inevitabilmente geometricamente meno precisa. Per una spiegazione geometrica di raggi vs curvature longitudinali rimando a questo articolo:
fixitwithshading.com/tag/fing...
Inoltre, le misure della tastiera non sono fisse e possono essere variate. Ad esempio la larghezza al capotasto potrebbe essere variata da un minimo di 23mm a un massimo di 24,5mm. Le concavità longitudinali potrebbero essere diminuite fino praticamente a zero (tastiera dritta), o aumentate rispetto a quelle indicate nel video in base allo stile esecutivo del violinista o al tipo di corde utilizzate. Il raggio di curvatura a fine tastiera può essere appiattito fino ad un massimo di 42mm, per adattarlo a una curva del ponticello più piatta mantenedo una altezza delle corde appropriata. Il raggio al capotasto è meglio mantenerlo sempre uguale (42mm), mentre il raggio centrale varierà in conseguenza degli altri due raggi: se si appiattisce il raggio a fine tastiera si appiattirà anche quello centrale. Se con 40,5 a fine tastiera è 38 a metà tastiera (come indicato nel video), con 41 a fine tastiera diventerà 38,5 a metà tastiera, con 41,5 alla fine sarà 39 a metà e con 42 sarà 39.5. L'altezza dei lati può essere aumentata fino a 5,5mm o diminuita fino a 5,0mm, e lo spessore della parte libera della tastiera può essere diminuito fino a 4,5mm o aumentato fino a 5,5mm.
English translation
Some makers do it differently, preferring a fixed radius and scoop instead of the compound radius and scoops I use. The fingerboard will still work, but will inevitably be geometrically less accurate. For an explanation of radius vs scoop, I refer to this article: fixitwithshading.com/tag/fing...
Moreover, the fingerboard measurements are not fixed and can be varied. For example, the width at the nut could be varied from a minimum of 23mm to a maximum of 24.5mm. The longitudinal concavities could be decreased to practically zero (straight fingerboard), or increased with respect to those indicated in the video based on the playing style of the violinist or the type of strings used. The radius of curvature at the end of the fingerboard can be flattened up to a maximum of 42mm, to adapt it to a flatter bridge curve while maintaining an appropriate string height. The radius at the nut is better to keep it always the same (42mm), while the central radius will vary as a result of the other two radiuses: if you flatten the radius at the end of the fingerboard the central one will also flatten. If with 40.5 at the end, it becomes 38 at the mid-fingerboard (as shown in the video), with 41 at the end it will become 38.5 at the mid-fingerboard, with 41.5 at the end it will be 39 and with 42 it will be 39.5. The height of the sides can be increased up to 5.5mm or decreased up to 5.0mm, and the thickness of the free part of the fingerboard can be decreased up to 4.5mm or increased up to 5.5mm.
0:00 - Violin fingerboard - Appendix
0:10 - Summary of measurements and how to take them
0:18 - Side view - Treble side 0,4mm - Bass side 0,6mm - Gluing plane 140mm - Offset planes 130mm
0:49 - Measurements - Light (of the sides) 0,5mm - Width 23,5mm - 42mm - Length 270mm
1:24 - Longitudinal concavity (light measured at half length) - E 0,35mm - A 0,40mm - D 0,50mm - G 0,60mm - Radius 42mm - 38mm - 40,5mm -
1:33 - Height of the sides 5.3mm
1:48 - Radius of curvature - Radius (at the nut) 42mm - Radius (at the middle of the fretboard) 38mm - Radius (at the end of the fretboard) 40.5mm
2:18 - Longitudinal concavity (light measured at half length) - E 0.35mm - A 0.40mm - D 0.50mm - G 0.60mm
2:45 - Measurements - Length 270mm - Gluing surface to the neck 137mm - Length of the hollowing 125mm - Thickness (of the hollowed part) 5mm - Width of the edges of the hollowing 1mm
3:25 - Thicknesses (overall) - 7mm (at the nut) - 11mm (at the end of the fingerboard)
Index of all my videos on violin making:
English: davidesora.altervista.org/vid...
Italiano: davidesora.altervista.org/video/
Davide Sora® is a registered trademark
Davide Sora® è un marchio registrato
#costruzioneviolino #violinmaking
Негізгі бет Tastiera di violino - Appendice - Riassunto delle misure e di come rilevarle
Пікірлер: 18