I fitted a TEC cam over a year ago in conjunction with the DNA air filter and inlet. I was much happier overtaking at 60mph /100 kph, I also noticed an improvement in fuel consumption, another benefit was the ability to fit a larger front sprocket which made the bike feel more relaxed. There were no starting problems even in the middle of a UK winter. As for the engine noise, I didn't really notice it over the increased induction roar from the DNA filter and intake, which was quite noticeable. I ran the new cam for 400 miles before starting to up the revs. At the time, in the UK it was £200 which I think was very good value for such worthwhile benefits.
@ONTWOWHEELSBEN
Жыл бұрын
Thanks for sharing your experience
@bulbakip6380
2 ай бұрын
How did off road performance go with the upgrades?
@wcronin7307
8 ай бұрын
Thanks for this. I just bought a 2022 Himi here in Canada and am seriously thinking of putting in this cam. Still not fully run in the engine though. Enjoying all your videos; very informative and detailed. Treating my Himi like a baby, lol and inspired by your knowledge.
@ONTWOWHEELSBEN
8 ай бұрын
The sooner you put in the cam the better . 😊
@adrianwaller-lq9si
Жыл бұрын
I’ve now fitted both TEC & Himalayan Tools camshafts now and both give the same rattle - probably due to a steeper ‘ramp off’ causing more clatter. My E5 has now done 5K miles on a TEC and runs really well (also with filter/exhaust/iridium plug/fuel x pro). Completely different bike from standard. Also now put 3K miles on an E4 with same set up except with booster plug and just the same in terms of performance. A ‘must do’ mod in my opinion 👍 6:48
@brucebennett9154
Жыл бұрын
Hi Ben, nicely done on the in-between info and intro to what is coming up. Keep up the good work and I'm look forward to the full review.
@crazybiscut
Жыл бұрын
Being a Scram 411 owner i am excited to see this
@niyojeet
Жыл бұрын
Same here, I have ordered it via my friend who lives in Germany
@mysterybiker1717
Жыл бұрын
Mine was noisy after tec cam and i set the valve clearances to the smallest enfield setting and noise gone. Tec cam suggest you can drop this below enfield minimum setting (drop by another ‘thou’) for even better performance. (Inlet and exhaust). Best mod you can make to himmy.
@ONTWOWHEELSBEN
Жыл бұрын
Yes , I tried dropping the clearances further, but the downside is when the engine warms up instead of freeing up it still stays tight resulting in tighter throttle response.
@sid0990
11 ай бұрын
@@ONTWOWHEELSBEN🤘🫠
@pggp273
8 ай бұрын
FFS! don't do it. it will screw your engine. you will always pay dearly in the longer term if you screw with tight valve clearances.
@TeamProCycle
11 ай бұрын
Great video series on your RE Himalayan. We are trying to get more support for the Himalayan here in the U.S. but, it is seeming to be impossible at the moment. Hopefully, riders such as yourself can get increased awareness and demand for products for the bike that the big manufacturers will start producing goods. Keep up the good work!
@ONTWOWHEELSBEN
11 ай бұрын
Thank you for the kind acknowledgment. The Himalayan is truly a fantastic machine .
@Jeru_on_the_road
9 ай бұрын
A little birdy told me, they are working on it! and that 2024, they should have more.
@soubarnokundu1002
Жыл бұрын
Waited for this video since ages
@malikkhan121
11 ай бұрын
Don't know Ben if you will read this or no. A year ago you spoke about ambient sensor location change. But there's no video on that 😢.. can you please help in finding and relocating the Ambient Temperature sensor location in Himalayan BS6. Appreciate your response 🙏
@subbu386
10 ай бұрын
Hey Ben, I have been watching your videos from Day 1 you have raised the Bar for every video and all the best for your upcoming videos too.. I have been searching for tec camshaft locally in hyderabad but i couldn't find them, Is there a place or a site where i can purchase it? or should i need to buy it from tec camshaft website and import it from them? Please do suggest it bro and i am looking for your thoughts on upgrading our OG himalyan with Big bore system as well. Do you recommend installing Bigbore 462cc from HitchCock motorcycles or 500cc from NMW racing team? For now i have installed Powertronics ECU + FuelX Pro + BMC Airfilter, Looking this month to upgrade my spark plug with NGK iridium and also looking to upgrade the front chain sprocket to 16 tooth. Looking forward for your response on this comment. All the best for your upcoming videos and looking forward for new videos on new braking system on OG the Himi :)
@AlwaRider
11 ай бұрын
Hi Ben...! Hope you are doing well.. As per your advice I have tightened up the steering stem lock nut.... Now there is no noise up there.. Thanks for that.. But now after doing that the handle moment is bit harder and it's not moving smoothly. I have also checked it by putting my bike on main stand and slowly move the handle bar on both side its not smooth somewhere in between. So what would you suggest? Should I change my conset bearing or I can fix it by some other way. If yes should I go for Conset fix combo from Art of motorcycles... Also for your better understanding I have 2022 himlayan and done only 10,000 km.
@martivn
Жыл бұрын
Making me want to buy one soooo bad 😍
@nandumon99
9 ай бұрын
bro just the cam should be enough or the valve and big bore kits needs to go with this?
@hemanthkanchi1209
2 ай бұрын
My bike after getting the TEC camshaft fit is making a lot of noise (looks like it is a noise from the tappet) is that ok? Should I make any changes to the valve clearances? P.s: It has only been about 100 km since I installed it (running it within 4000 rpm)
@ONTWOWHEELSBEN
2 ай бұрын
Watch all my videos on TeC camshaft. Valve clearance setting to be done at slightly warm engine . 2-3 mins of idling and then set valve clearance. .08mm inlet , .23 mm exhaust. Get it done by a professional. They do make noise . It will slowly improve with time ( 3-5000 kms ).
@Chris64France
9 ай бұрын
Hello, did you change the ECU setup in addition?
@matusknives
17 күн бұрын
Is there any information available as to what happens to the emissions?
@ONTWOWHEELSBEN
17 күн бұрын
@@matusknives if you run the cam along with a fuel commander then yes it will increase. If you introduce the cam to the stock setup there should Be a mild difference
@matusknives
17 күн бұрын
@@ONTWOWHEELSBEN thank you
@AlwaRider
Жыл бұрын
Hi Ben, I'm having RE himalyan bs6 I'm getting some noise issues from the front side near or down the meter console I'm exactly not sure where it comes from and it comes frequently on speed breakers and on bad roads Kindly suggest what to check and how to fix it.
@ONTWOWHEELSBEN
Жыл бұрын
Tighten the steering stem lock nut .
@DSmith-rc7gu
11 ай бұрын
Someone also suggested windshield mounting clips and used heavy tape to dampen vibration. It worked.
@lifelover5810
11 ай бұрын
@@DSmith-rc7gu I cut washers from an old tube rubber and put them around windscreen screws from both sides, no more rattle
@Jonathan-L
Жыл бұрын
Absolutely Bensational!
@Actor037
Жыл бұрын
Hi Ben, What's your opinion on the new Himalayan 450 design ? 👻
@ONTWOWHEELSBEN
Жыл бұрын
It’s fantastic, will grow on everyone , but it isint an original like the 411 .
@meow-says-the-cat
Жыл бұрын
I'm looking forward to when I get mine, I know just which channel to turn to :)
@ONTWOWHEELSBEN
Жыл бұрын
❤️
@trinkabuszczuk6138
27 күн бұрын
With all their R&D, why don’t RE fit this cam pattern as standard? If you can make the bike better, make it better! 🤔
@cca749
Жыл бұрын
Great job brother!
@ONTWOWHEELSBEN
Жыл бұрын
Thanks Brother
@hemantakaushik4635
Жыл бұрын
Good video Ben. Thank you.
@jonc4752
Жыл бұрын
I've done over 4000miles on a Tec Cam... it made absolutely no difference what so ever to the noise levels. I keep the valves adjusted periodically just as before. I think you could check your tensioner perhaps.
@ONTWOWHEELSBEN
Жыл бұрын
Any cam with OVERLAP does increase decibel levels . This isn’t just my experience.
@jonc4752
Жыл бұрын
I can only go by my own experience having fitted it myself, but I stand by what I say. I've had my Himalayan nearly 4 years, so like yourself, not only do I love it, but I like to think I know the bikes nature extremely well...maybe I just got lucky! :)
@ONTWOWHEELSBEN
Жыл бұрын
@@jonc4752 when did you install the camshaft , at what mileage?
@jonc4752
Жыл бұрын
@ONTWOWHEELSBEN I would say at about 1500 miles if I can remember rightly, I'm not a big mileage user like yourself, so who knows, noise levels may change as time goes by. I have most of the other mods as well, filter exhaust, etc. and she runs great. My only minor complaint is that, "very occasionally" it will hesitate for a split second on the starter if the engine came to rest previously on the wrong part of the stroke. I assume that's due to now having no decompressor... It's extremely rare though. I love the bike and would never upgrade to the 450.
@BioSystemV8
9 ай бұрын
Experienced the same, no difference in cam noise, did about 7k miles, also did not had to adjust lash, I'm alwasy check but not a single adjust since I fitted the cams.
@sachi-abhi
Жыл бұрын
Watend know, Is it able to cruise comfortably at 120km/hr.
@ONTWOWHEELSBEN
Жыл бұрын
Wait for my video on the same
@markberney300
5 ай бұрын
My bike is no noisier than it was before fitting the TEC cam. I am a mechanic and I service my Himi myself.
@ONTWOWHEELSBEN
5 ай бұрын
Then you were already running slightly loose valve clearances
@markberney300
4 ай бұрын
@@ONTWOWHEELSBEN absolutely not.
@kenny4k
2 ай бұрын
If you live in a cooler climate you can get away with slightly tighter valve clearance btw
@drspock3454
7 ай бұрын
Are these cams available for purchase in india or do i have to order from the uk? Is there any difference between the rec cam and the hitchcocks performance cam?
@ONTWOWHEELSBEN
7 ай бұрын
Speed monks Delhi
@Himalayanbiker411
Жыл бұрын
Amazing 😻
@SUDIPTA1976
Жыл бұрын
Ben sir, what's your take on the news that new Himalayan 452 will replace our 411 and it will be discontinued soon?
@ONTWOWHEELSBEN
Жыл бұрын
Don’t know about the 411 being discontinued
@SUDIPTA1976
Жыл бұрын
Oh okay sir.
@eastsidebadger8416
Жыл бұрын
@@ONTWOWHEELSBENCan’t see RE keeping the 411..they’re going to want everyone to buy the 452.
@yasin_mhd_
Жыл бұрын
Do a dyno run bro. I'm waiting to see the gains
@yasin_mhd_
Жыл бұрын
@@judythomas2939 Available on Banglore Race dynamics and Delhi Speedmonks, rest i don't know bro.
@avishekchakrabarty2560
Жыл бұрын
@@judythomas2939many
@pggp273
8 ай бұрын
He wont mate because the difference will be of no beneficial gain. Any benefit of pissing around with your engine like this will be in his head and not the dyno read out
@chrisfrantz2674
5 ай бұрын
@@pggp273 Tec has a dyno chart on their website confirming ~20% gains in hp and torque
@soubarnokundu1002
Жыл бұрын
Any substitute in India ? Of the tec cam since it’s not available in the Indian market
@ONTWOWHEELSBEN
Жыл бұрын
I wouldn’t recommend any other than seasoned parts manufacturers when it comes to engine internals . Tec & aHitchcocks & Himalayan tools cam
@aviator9985
Жыл бұрын
Hi! Ben, Long time no see?
@SK_00001
Жыл бұрын
❤️🔥❤️🔥❤️🔥
@peterbell5556
Жыл бұрын
Hi Ben, is this the same as the cam from hitchcocks?
@ONTWOWHEELSBEN
Жыл бұрын
No . Very different
@pggp273
8 ай бұрын
No because you might actually see some benefit from the Hitchcock's cam rather than any imaginary gain with this piece of garbage. Although I wouldn't recommend either.
@CondeNastCruiser
9 ай бұрын
I need to upgrade my Himalayan breaks. Any suggestions?
@ONTWOWHEELSBEN
9 ай бұрын
EBC semi sintered , Vesrah ceramic watch my videos on the same in mods playlist
@worklada9533
2 ай бұрын
Vesrah is all day along🙌🏼
@madgaming2811
Жыл бұрын
Just waiting for the Himalayan 452
@mysterybiker1717
Жыл бұрын
Cant say i noticed any difference. Much better with valves set tight and valves open for longer so in theory a slight power gain
@JanakaSunil
8 ай бұрын
Does camshaft upgrade require ecu re map?
@ONTWOWHEELSBEN
8 ай бұрын
Not this camshaft
@royaritra1
Жыл бұрын
❤
@debiprasadsahu2002
9 ай бұрын
Pls make an acceleration test of this himalayan
@pggp273
8 ай бұрын
He wont because in reality it makes very little difference. Any notable difference will be in his head only and not on the clock
@debiprasadsahu2002
8 ай бұрын
@@pggp273 true
@worklada9533
2 ай бұрын
@@pggp273haha, not really. Actually the tec camshaft changes the power graph itself. It's so well designed that it helps the engine to burn all the fuel inside the combustion chamber.
@pggp273
2 ай бұрын
@@worklada9533 If you have to make ridiculous modifications to your motorcycle to massage your own ego. Please at least buy a quality bit of kit from Hitchcock's rather than this piece of garbage made from putty
@pggp273
2 ай бұрын
@@worklada9533 Yeah right ! Like Royal Enfield hadn't thought of that. It never ceases to amaze me that manufactures spend millions on R&D and some wanker in a shed thinks he knows better. Spoiler alert He doesn't
@makuru3395
Жыл бұрын
well done🥸👌🖖
@klano8443
Жыл бұрын
Some people say it's quieter
@ONTWOWHEELSBEN
Жыл бұрын
Yes if the stock camshaft is worn and the valve specs are off
@pggp273
8 ай бұрын
What ever you do DONT DO THIS it will be a huge mistake. If the engine was meant to have a camshaft that operated this way RE would have fitted it. If you want a faster motorcycle then buy a faster motorcycle. Don't do shit like this thinking it will make your motorcycle better because it wont. Most of the improvement if any will be in your head because you spent so much time and money you will convince yourself it was worth it. Spoiler Alert Its NOT !
@stevetaylor8698
Жыл бұрын
Just buy a Honda 500
@ONTWOWHEELSBEN
Жыл бұрын
And go trail and rock riding ? Will have to shell out even more money to make it off road worthy . End use matters . I am more into riding off road .
@peterasmussen2933
11 ай бұрын
cam does not affect braking, speed does. What you say about braking is absurd!
@ONTWOWHEELSBEN
11 ай бұрын
Increased acceleration causes increase in momentum and that is why one needs to upgrade to better brakes .
Пікірлер: 94