this channel is becoming, very quickly, one of my favorite channels for head work
@ercost60
Жыл бұрын
4:40 I'm freaking out! This is such a great video!
@Billy_Built
7 ай бұрын
haha I'm learning the importance of proper valve guide clearancing the hard way. Thanks for this video!
@headgames
7 ай бұрын
Sorry to hear that! Hopefully this helps
@ayoustin6077
Жыл бұрын
Straightforward and easy to understand, great vid. Would be interested to see how you polish cams after they've had contaminated oil run through. Also would be interested to hear your take on deck surface finish, does the head need to be milled every time it is serviced to get a fresh surface?
@headgames
Жыл бұрын
dude! Thanks for the feedback and the vid ideas!
@MechInvent
Жыл бұрын
I've always been told size is a personal preference for my reamer size too.
@THEBULLETPROOFGARAGE
Жыл бұрын
Excellent video. I'm about to tackle the same job for the first time on a Ford/International 7.3 IDI diesel. Thanks
@MrJermbob
Жыл бұрын
Very interesting stuff. Thank you for your videos.
@paigeGodwin-bj3ms
4 ай бұрын
i like the loose joke 🤣 great video thank you!
@headgames
4 ай бұрын
Thanks for watching!
@nitrofever
11 ай бұрын
Do you hone after reaming ? I’ve heard the finish is ready to run after reaming, others say the hone holds oil…but will polish out over time…thanks
@headgames
3 ай бұрын
we just ream, no need to hone it unless it is not to size.
@RR-qd2gz
Жыл бұрын
Most excellent video thank you
@headgames
Жыл бұрын
thanks!
@rafaellastracom6411
10 ай бұрын
Perfectly acceptable. We´re not going to the moon.
@rollthelosingdice
8 ай бұрын
Good thing no one's been there.
@DavidThomas-id2fz
Жыл бұрын
What is the style/model of reamer you're using? A lot of reamers I see for sale online look much shorter. I'm looking to enlarge my 5/16" valve guides to 11/32" on small block mopar magnum heads. thanks
@headgames
Жыл бұрын
hit up Dakota Parts Warehouse. They are not cheap. And that is a big jump.
@prophet6896
Жыл бұрын
Interesting videos. Any experience with Subaru FB16 engines? Am planning to rebuild one NA for 200 whp
@headgames
Жыл бұрын
Never even heard of that engine. So that’s a no
@prophet6896
Жыл бұрын
The FB engines are Subaru newest engines. So they have FB16, FB20, and FB25
@prophet6896
Жыл бұрын
@@headgames The FB blocks are more economic for fuel efficiency etc so they are very slow compared to the EJ and FA series
@prophet6896
Жыл бұрын
@@headgames The setup is basically the same as other Subaru engine models. They are the same boxer type engines
@sdfilmfolks
Жыл бұрын
Thanks man.
@headgames
Жыл бұрын
thank you!
@AshLongie
3 ай бұрын
Would be nice to know clearance used in that application
@headgames
3 ай бұрын
.001-.0012
@AshLongie
3 ай бұрын
0000 thanks I live for the little detail thanks man great vid
@jackdipper7686
Жыл бұрын
Good vid
@headgames
Жыл бұрын
thanks!
@khemrajhsamaroo3671
Жыл бұрын
You guys sell valve guide reamers for the 4G63 ?
@zc18crx
Жыл бұрын
So, does the valve to guide clearance change with the type of environment its going to be used in?
@headgames
Жыл бұрын
Great question! Yes, but only a few tenths of a thousandths
@REPerformanceUK
Жыл бұрын
Hello Dave, why do you ream your guides over honing? Love the vids mate!
@headgames
Жыл бұрын
@@REPerformanceUK Thanks for the kind words! Great question! Because it's so much faster and more repeatable to get the correct reamer vs honing. We do still hone a few things but for the most part we ream all of our most common.
@prophet6896
Жыл бұрын
@@headgames Does valve clearance adjustment add to horsepower?
@headgames
Жыл бұрын
@@prophet6896 I have heard people say that but I don’t think it’s true. A couple of thousandths of an inch is not enough to sway your whp.
@AltezzaNikku
Жыл бұрын
Hello, over the winter i eanted to port my supercharger 1G-fe engine. It comes na stock, is there anything to look for when porting an cylinder gead with a "fuel econmic" design that is turned into a performance engine. Is there any way to know that i wont hit any cooling channels ?
@headgames
Жыл бұрын
I would just leave it alone unless your making some real power with it. 800+whp then worry about porting it. We have never done a 1G-FE to know dimensions on how big to make it. If you hear it an echo stop!
@AlisoBob
4 ай бұрын
If I call Dakota, they can hook me up with any size reem?
Пікірлер: 55