Creativity is great. Such a transformation can make the multimeter more useful. Our multimeter wire is very soft, resistant to cold in winter and heat in summer, and easy to use.
@bo-dine7971
Жыл бұрын
Some weak devices may get damaged by the inrush of the .1uF cap, so it'd be good to come up with some kind of limiter, but otherwise this is simple & great for most things you'll test.
@yankozlatanov
Жыл бұрын
Its a joulethief with rectified output and low capacity capacitor to hold the voltage for the testing. Nice idea for zener diodes and leds.
@sanusitunde8266
Жыл бұрын
Thanks for this useful circuit. Now i can test any zener diode without trouble
@MrDinosaur41
Жыл бұрын
Yes, you can, but be careful with LEDs that can fail when reversed without withstanding 64 volts.
@ganapathipai8853
Жыл бұрын
Great news for the day. I usually use mains operated dc coupled supply to check LED backlight strips. This one is safe thanks
@jesussalcido
2 жыл бұрын
Excelente Idea¡ Ya estoy pensando en instalar el circuito dentro de un viejo Multimetro FLUKE dedicado a probar Zeners y Diodos . Claro de manera limpia y profecional. Mil Gracias Por La Idea¡
@Inventor_AW
2 жыл бұрын
Buena suerte
@neptran5728
2 жыл бұрын
Praktisch ideal um Halbleiter auszumessen, die eine hohe Durchbruchspannung haben. Vielen Dank, das Teil ist sehr gut !!! Inventor AW
@Inventor_AW
2 жыл бұрын
Danke dir
@emanikebiz
9 ай бұрын
Una consulta: q funcion cumple el transistor? No conduce cuando haces corto? Osea p protejer o q no se consuma rapido la pila o cual?
@user-kz2sc4vb3l
Жыл бұрын
Надо сразу говорить что это такое ! Может человеку это не надо а вы заставляете его ждать пока вы скажете что это!
@paulocezarcarmo794
3 ай бұрын
he is not concerned with clarifying to anyone what it is, but rather getting views
@user-ju2yl6bz9y
3 ай бұрын
@@paulocezarcarmo794 в таком случае это кликбэйт
@Alex-zm1fx
2 ай бұрын
А у тя типо перемотка не фурычит, да?👎
@user-ju2yl6bz9y
2 ай бұрын
@@Alex-zm1fx вобще то такие названия роликов это кликбэйт, раньше на площадке было чище по тому что их своевременно удаляли.
@satellite-113
Жыл бұрын
Спасибо за видео и за схему с демонстрацией изготовления, и применения. Удачи!
@Inventor_AW
Жыл бұрын
Спасибо
@satellite-113
Жыл бұрын
@@user-wu3yi5eq2e , а Вы видео смотрели?
@user-wu3yi5eq2e
Жыл бұрын
@@satellite-113 Сматрел, но ничё ни понил.😥
@satellite-113
Жыл бұрын
@@user-wu3yi5eq2e , если Вы ничего не поняли, то Вам лучше темы электроники не касаться и не пробовать, что-то делать без изучения начального уровня(это как раз для того, чтобы ничего не взорвалось(не в данной схеме, а вообще)).
@user-wu3yi5eq2e
Жыл бұрын
@@satellite-113 СПСБ, друх.👍
@germanalvarado3544
Жыл бұрын
Excelente....funciona al 100%...muy Buen Invento, saludos desde Costa Rica
@Inventor_AW
Жыл бұрын
gracias
@abdelwhabyoussefelnaili3207
2 жыл бұрын
100× 100 عبقري ممتاز جدا بارك الله فيك 🌹شكرا
@Inventor_AW
2 жыл бұрын
اشكرك
@enriqueatala2567
Жыл бұрын
great project! and good idea of Abduladhim Abdullatif. Saludos desde Argentina
@Inventor_AW
Жыл бұрын
thanks
@andreascarl6428
Жыл бұрын
I liked the idea. A suggestion: The working frequency is probably quite high so I believe that replacing the 1N4007 diode with a fast recovery diode like the UF4007 can generate a higher voltage and perhaps reduce transistor heating and battery consumption. I think this type of diode can be found in scrap electronic ballasts for fluorescent lights.
@Inventor_AW
Жыл бұрын
Good idea..thank you
@charonjr1701
Жыл бұрын
6 DEC 22 - I tried winding AWG 17 on a 1.5" hollow, cylindrical ferrite core. The wire was solid core, coated in purple vinyl. My weakened hands and fingers could barely bend the wire. It was nothing like what inventor AW used. I had to superglue two plastic bottle caps to the ends of the cylinders to make anchor points and allow walls for the windings to align with. Unfortunately, in widening the anchor slot with a pair of fine cutters, I did *something* that caused a chunk of the ferrite core to fly off into the world somewhere. The missing chunk appears to be a quarter of the cylinder. Went back to Elliot's Electronics, here in Tucson, and found a $2 manufactured cylindrical core with AWG 26 magnet wire (enamel or lacquer coated; not sure which) wound about within it. I've extracted the wire and am working on winding the 20/50 shown in the video. 26 is much easier to work with, though it taxes the limits of my dexterity. I just wound the first 20, and am going to lay down a layer of kapton tape to isolate the 20 windings from the next 50. The 50 will be done tomorrow. :)
@Inventor_AW
Жыл бұрын
good job
@Muslim_011
Жыл бұрын
Very nice. Just what I wanted. I was thinking for a led power circuit from a light Led Bulb but was dangerous. Your Idea is brilliant 👍👍👍
@Inventor_AW
Жыл бұрын
thanks
@HydrO152
Жыл бұрын
I have made same circuit but it's only showing 1v to 0.98v why?
@englishrupe01
Ай бұрын
@@HydrO152 Bad transistor?
@kamranjavaid
Жыл бұрын
Can this be used for testing capacitors, means some sort of ESR meter alternative?
@Inventor_AW
Жыл бұрын
No
@rajpradip4329
11 ай бұрын
Thank you for video.
@abdelkaouibenmalek3395
Жыл бұрын
thank you 😊
@frankwalter1803
2 жыл бұрын
Danke für die einfache, aber interesante Meß-Schaltungsergänzung. Frage: Im Clip sind es bei der Spule 20 und 50 Windungen, im Plan sind es 15 bzw.40-45, was ist denn besser ? 2te Frage: Diesen Transistor "D882", mir ein gänzlich unbekannter Typ! Die Gehäuseform entspicht "BD 135 (..137; ..139), sind diese geeignet ?
@Inventor_AW
2 жыл бұрын
20/50 ist besser Hier die Alternativen zum verwendeten Transistor: 2Sd882 2SB77 2Sd882 2SC136 2Sd882 MJE182 2Sd882 KSD882 2Sd882 BD437 HSd882 BD437 KSd882 BD437 KSd882 2SD882 KSd882 2SD1225M KSd882 2SC932 KSd882 2SC931 KSd882 2SC3422 KSd882 2SC1568 KSd882 2SC1243 KSd882 MJE182
@frankwalter1803
2 жыл бұрын
@@Inventor_AW Danke für die Antwort., Schade, habe mich schon auf meinen genannten BD typ gefreut, ist natürlich ein anderer,..
@charonjr1701
Жыл бұрын
30 NOV 22 - Your ferrite core is about 1" (25.4mm) long compared to your forefinger knuckle. 20 winds plus 2 semi-winds (terminals at each end) divided into 25.4mm = 1.1545mm diameter: You are using AWG 17 wire?
@Snoopy56
Жыл бұрын
Buenos días saludos cordiales desde Agua Dulce Veracruz muy buen proyecto para adaptar al multímetro y medir y saber si esta en condiciones y su voltaje de operación gracias por compartir
@lifuhen9913
Жыл бұрын
Имеет смысл добавить последовательно выходу резистор приблизительно 5-10 Ом, что бы в момент включения, не было шока для светодиода?
@ukrainian_bear
Жыл бұрын
Имеет смысл даже больше добавить, причем раз, этак, в 10 больше.
@scalperman
Жыл бұрын
Thanks for sharing your great idea. Although easy to make, could you share the wiring diagram with a link? Congratulations again
@Inventor_AW
Жыл бұрын
i will
@piligrimpiligrimik6728
Жыл бұрын
@@Inventor_AW Ping.
@lingli314
2 жыл бұрын
Can we replaced the transistor with FET to save the battery's life. Batt + to base is a huge current flow to emitter.
@Inventor_AW
2 жыл бұрын
I will try
@piligrimpiligrimik6728
Жыл бұрын
Як мінімум, можна додати конденсатор між базою і виводом трансформатора, щоб відсікти постійну складову
@apachecomm
2 жыл бұрын
Thank you very much
@user-ko8zv6kj3m
Жыл бұрын
Cool idea.👍
@abduladhimabdullatif6345
2 жыл бұрын
Thanks so much for such a great and creative idea. I will try building it using an 18650 lithium battery instead of 1.5volts. this way, I can charge the battery with an external battery charger as needed. May I also suggest using a 0.36 Inch voltage meter instead of a multimeter and package everything (the circuit, battery and voltmeter) on a small plastic container. This way it becomes a stand-alone LED measurement tool. Thanks again
@Inventor_AW
2 жыл бұрын
Good luck
@andreascarl6428
Жыл бұрын
The idea is good. But I think you will have problems with the led meter and the working voltage of the transistor. The current that the circuit supplies is very low and even if it is enough to make the meter work, it will cause the output voltage to drop. I advise you to use the 3-wire model with the power connected directly to the 18650 battery and the third wire to the circuit output. The ones I have here at home work well with 4 volts, I don't know if all are like that. Also, feeding the circuit with approximately 4 volts will make the output voltage easily exceed the measurement limit of 100 volts, I don't know how much these meters support at the input without burning out. And obviously you will have to use a transistor for a higher voltage and current and a bigger heatsink too. One solution might be to place a resistor between the battery positive and the circuit input to reduce the 4 volts. Start with 10k and try lower values until the circuit works correctly. With values below 1k use resistors for 1 watt or more. I also recommend an electrolytic capacitor of about 100 uF or more at the input of the circuit.
@franciscobrito8017
Жыл бұрын
1
@user-mf1ew2in8s
2 ай бұрын
@@andreascarl6428для этого можно использовать отдельное питание
@veeem3964
11 ай бұрын
Which range should the multi meter be set on with this circuit
@Inventor_AW
11 ай бұрын
DC 200V range
@edwinlipton
Жыл бұрын
NOW that's Koool, and USEFUL!! 👍
@Inventor_AW
Жыл бұрын
thanks
@leonidasbsilva9753
2 жыл бұрын
Ótima ideia, parabéns!
@Inventor_AW
Жыл бұрын
Obrigado
@kingshahzad78
Күн бұрын
Great Tester You Made Sir❤
@Inventor_AW
Күн бұрын
thanks
@joseorlandorinconarias9873
2 жыл бұрын
Una pregunta Profe..¿Que pasa si en lugar de colocar un potenciometro de 10 kilo ohms , coloco un pote de 20 kilo ohms?..Gracias por su buen proyecto electronico 👍
@Inventor_AW
2 жыл бұрын
No usé 10 kOhm
@user-wi5qv5xx3x
7 ай бұрын
Bravo...
@user-hu8qq2qf2e
Жыл бұрын
How many volt are max for input source instead 1.5v?
@Inventor_AW
Жыл бұрын
You can use 3V with 100 ohm impedance mode
@T0berius
2 жыл бұрын
Gracias por compartir. Que estariamos midiendo con este dispositivo ?
@Inventor_AW
2 жыл бұрын
Medición de semiconductores como LED
@Juniorfinger999
2 жыл бұрын
Brp lilitan untuk coil/tembaga? Untuk selain d288
@Inventor_AW
2 жыл бұрын
20/50
@favuche6726
Жыл бұрын
Fantastic job
@Inventor_AW
Жыл бұрын
thank u
@adelsonsilva5630
2 жыл бұрын
Bom dia professor éu fize com o bd139 mais só que quando faso o teste no led a tensão quai não dar o valor da tensão do led qual é o ploblema
Boa tarde professor posso fazer este circuito usando o bd139 no lugar do d882
@Inventor_AW
2 жыл бұрын
Sim você pode
@andreascarl6428
Жыл бұрын
Eu pensei a mesma coisa. A corrente do BD139 é a metade do D882 , 1,5 A mas deve ser suficiente. Cuidado com a enxurrada de Bds falsificados, eu peguei um lote há uns 3 anos e ontem fui na casa de um colega também eletrônico que me mostrou um saquinho cheio deles. É por e queimar. Assim como os meus os dele grudam em ímãs.
@CoverAISong
Жыл бұрын
BD241C работает
@viswanathanramakrishnan7613
Жыл бұрын
What's the gauge of the copper wire? Is it the same wire removed from the coil or different?
@Inventor_AW
Жыл бұрын
the same
@damianedy629
9 ай бұрын
@@Inventor_AW how thick is the copper wire of this coil
@mohammadawwad6598
Жыл бұрын
Thank good idea
@dens7117
2 жыл бұрын
Оригинальное применение блокинг-генератора
@sudippramanik1307
2 жыл бұрын
Superb!
@Inventor_AW
2 жыл бұрын
thank you
@alvarofuentesarjona2668
11 ай бұрын
Muy buen proyecto. No logré conseguir en mi área el capacitor 204J de 0.2 uf. Por cual podría reemplazarlo?
@Inventor_AW
11 ай бұрын
try 104J
@luizcarlossantana9620
Жыл бұрын
Hi I am from Brasil, I liked very much your chanel. Congratulations.
@Inventor_AW
Жыл бұрын
thank you sir
@zona-de-pruebas
2 жыл бұрын
Porque se elige el d882 y no otro tipo de transistor npn?
@Inventor_AW
2 жыл бұрын
Puedes usar otro tipo de npn
@user-lv5mw6kd5f
Жыл бұрын
کارت خیلی عالی است
@aiblack60
Жыл бұрын
Собрал, работает. Но сильно занижает напряжение стабилизации стабилитрона. (Наверное, дело в мультиметре, который измеряет среднеквадратичное напряжение, а напряжение в данном случае пульсирует). Можно ли исправить, чтоб и стабилитрон не повредить? Спасибо
@user-jc3kx7hr7p
Жыл бұрын
Я бы добавил на выход резистор 5-10 k (последовательно) - пульсации уменьшатся, и для светодиодов безопаснее - они не любят резкий запуск. Ёмкость конденсатора тоже можно увеличить.
@javierrodriguez-jj8cz
2 жыл бұрын
¿CUAL ES SU FINALIDAD DEL CKTO?..DE PRUEBA, PROTECCION..O ALGO MAS..GRACIAS..
@Inventor_AW
2 жыл бұрын
prueba de semiconductores
@falandoareal4578
Жыл бұрын
TOP D+
@5885ronny
Жыл бұрын
Gut 👍🤗
@hoseinmnb7900
2 жыл бұрын
Perfect
@Inventor_AW
2 жыл бұрын
thanks
@Eletrolitico
Жыл бұрын
genial. obrigado por compartilhar.
@Inventor_AW
Жыл бұрын
Obrigado
@madhusudangupta3661
4 ай бұрын
What is the maximum current at the probes of Multimeter?
@Inventor_AW
4 ай бұрын
¿Te refieres a este circuito electrónico? ¿O en general?
@madhusudangupta3661
4 ай бұрын
@@Inventor_AW, Obviously my question pertains to this circuit.
@Inventor_AW
4 ай бұрын
20mA @@madhusudangupta3661
@maiconjz3527
2 жыл бұрын
Excelente, 10.
@Inventor_AW
2 жыл бұрын
thanks
@samratbarua7977
Жыл бұрын
Super 👍💚
@mtrltoolman
2 жыл бұрын
Boost converter circuit
@vovchjkvovchik9061
Жыл бұрын
Лайк заслуженный за проделанную работу и интересную схему. Вопрос: бедет данная схема работать от 5в или USB ? Если да то какие изменения нужно внести в схему? Удачи вам и вашему Каналу.
@Inventor_AW
Жыл бұрын
Вам понадобится много модификаций, таких как: количество витков катушки, добавление сопротивления и замена транзистора. Позже я изготовлю такой, который зависит от 5 вольт.
@vovchjkvovchik9061
Жыл бұрын
@@Inventor_AW Ждём следующего видио от питания USB . Удачи вам и Здоровья.
@user-rp9gu3qh3q
Жыл бұрын
@@Inventor_AW В мультиметре, на разъеме для проверки транзисторов, есть 3 вольта. Интересна схема чтобы без автономного источника питания. Но вот как эти 3 вольта завязаны гальванически с Кроной, и какова нагрузочная способность этого напряжения? Вроде в журнале Радио я видел нечто подобное от Игоря Нечаева. Но его схемы чаще не работают чем работают. Он их наверно и не собирает. Выдает на гора. Член редколлегии журнала Радио
@FWS99channel
Жыл бұрын
good idea.
@carlosoliveirahobbista8614
Жыл бұрын
show gostei obrigado por compatilhar
@Inventor_AW
Жыл бұрын
Obrigado
@uaoodh2233
Жыл бұрын
COOL NICE 👍 👍 👍 👍 👍 Running 1.5V to 65.9V
@greenmorda
Жыл бұрын
Did someone heard about LED avalanche on reverse voltage?
@Vidya1939
Жыл бұрын
Nice tester I liked it
@Inventor_AW
Жыл бұрын
thanks
@alializadeh8195
2 жыл бұрын
Thanx
@carlosfranciscoalcocerterr6933
2 жыл бұрын
Esta bueno pero no me da el voltaje correcto del LED puesto los LED de televisores son de menos voltaje ahí muestra 6.3 v pero los LED que muestran es de 3v y en la otra prueba muestra 14 .5 y es ilógico que sea de ese voltaje
@Inventor_AW
2 жыл бұрын
arreglaré eso
@jimparsons6803
2 жыл бұрын
How about that? Using the output voltages from a small fly-back (?) circuit to test the working voltages of other devices? Well done and well thought out.
@Inventor_AW
2 жыл бұрын
You can use it in measuring semiconductors
@andrimastirta4736
Жыл бұрын
I've made exactly same with that.. But when i connect to battery at the first the voltage increase, but not stable like your. I used fresh new battery. After a few seconds the voltage drop fastly. I wonder where is the fault?
@hpnetwork5928
Жыл бұрын
Have you used a heatsink?
@hpnetwork5928
Жыл бұрын
Is it shorting any pins ?
@Inventor_AW
Жыл бұрын
Check the connections and the number of turns of the coil
@andrimastirta4736
Жыл бұрын
@@hpnetwork5928 i had.. 🙂
@andrimastirta4736
Жыл бұрын
@@hpnetwork5928 alredy double check before turning on.🙂
@user-bd8yv2xy7w
Жыл бұрын
Молодец я сделал очень помогает в проверке стабилитрон и не только.
@silviopereira8868
2 жыл бұрын
Simples G - R - E - A - T !!!
@Inventor_AW
2 жыл бұрын
thanks
@MrKelli007
2 жыл бұрын
спасибо!!! толковая схема
@mihailrudenko8263
Жыл бұрын
Схема рабочая! Спасибо!
@Inventor_AW
Жыл бұрын
Пожалуйста
@juancarlospalenciaavila8565
2 жыл бұрын
Gracias por la información.
@Inventor_AW
2 жыл бұрын
Saudações para você
@fethiozturk3999
2 жыл бұрын
Only led tester ? Motor or Other Elektric Models? 😋
@Inventor_AW
2 жыл бұрын
You can use it however you like
@gleybisondossantos9412
Жыл бұрын
Projeto imcrivel amigo
@Inventor_AW
Жыл бұрын
Obrigado
@electproject
2 жыл бұрын
awesome
@Inventor_AW
2 жыл бұрын
thanks
@ahmedsoffy581
Жыл бұрын
really its perfect invention > congratulation
@Inventor_AW
Жыл бұрын
thank you
@user-oj1zv4iq7i
Жыл бұрын
Добрый день. Идея интересная , а самое главное нужная для проверки стабилитронов и светодиодов. Вопрос: возможно ли запитать эту схему напряжением 5в от USB ?
@Inventor_AW
Жыл бұрын
Да, можно, с некоторыми изменениями
@user-oj1zv4iq7i
Жыл бұрын
@@Inventor_AW Утро доброе . Спасибо за ответ. Не могли бы описать какие изменения нужно внести ?
@rusg.8929
Жыл бұрын
При включении выходит из строя транзистор.Почему?Какова индуктивность катушки.
@emanikebiz
Жыл бұрын
Muy bueno.
@franciscoprata8465
Жыл бұрын
Boa noite amigo! Ótima ideia. Poderia dizer qual o consumo de corrente do aparelho. Obrigado, Francisco Prata desde Brasil.
@Inventor_AW
Жыл бұрын
Obrigado meu amigo, mas não entendi sua pergunta
@franciscoprata8465
Ай бұрын
@@Inventor_AW Desculpe Sr. A pergunta é simples: Qual o consumo do circuito sem estar fazendo testes? A bateria é durável? Obrigado.
@Inventor_AW
Ай бұрын
@@franciscoprata8465 O circuito consome a bateria rapidamente, e esse é o único inconveniente, vou desenvolvê-lo para que não consuma energia e vou torná-lo recarregável.
@ralphkekobadarati605
Жыл бұрын
Show mto bom,sempre some abço.
@Inventor_AW
Жыл бұрын
obrigada
@ruslanaliev4675
7 ай бұрын
Отлично 👍,но пожалуйста выключи эту музыку в следующих роликах
@nasannasan7521
2 жыл бұрын
👍👍
@hosnymahmoud869
Жыл бұрын
good idea 💪
@Inventor_AW
Жыл бұрын
thanks
@josebotelho3571
2 жыл бұрын
👌👍
@electroboy3607
Жыл бұрын
Thnaks so nice vedio...verry usefull..vedio
@bulentdemir6641
Жыл бұрын
harika fikir.
@akharin2023
Жыл бұрын
خیلی خیلی عالی iliked teh idea goooooooooooooooooooood 😏👍👍👍👍👍👍👍👍👍👍👍👍👍👍
@Inventor_AW
Жыл бұрын
thanks
@timhartherz5652
Жыл бұрын
So you basically used a variant ot the "jule thief" as a current limited voltage source to finf the forward voltage of LED's or the nominal Voltage of a Zener diode.
@Inventor_AW
Жыл бұрын
surely
@vanfakof6012
Жыл бұрын
👍👍👍
@luizfernandolessa1889
2 жыл бұрын
Boa tarde.Vou tentar fazer colocando acoplado a um voltímetro; mas qual o valor correto do capac. de saída e qual o número de voltas na bobina? pois o diagrama está com mensuras distintas do circuito confeccionado. Forte abraço do Brasil.
@Inventor_AW
2 жыл бұрын
Capacidade do capacitor 0,1 ou 0,2 micro / número de voltas 20 voltas e mais 50 voltas.
@luizfernandolessa1889
Жыл бұрын
@@Inventor_AW Grato.
@giannilorusso9924
2 жыл бұрын
Bravo
@Inventor_AW
2 жыл бұрын
thanks
@AnkitJaiswalOfficial
Жыл бұрын
Wire Gauge?? Used in Coil.
@Inventor_AW
Жыл бұрын
1m
@jimmartin8853
5 ай бұрын
Doesn't this circuit kill a AA, 1.5V battery pretty quick?
@Inventor_AW
5 ай бұрын
Yes..you can use a rechargeable AA battery
@jessecardoso5529
2 жыл бұрын
Poderia comercializar....você vende?
@Inventor_AW
2 жыл бұрын
Eu não vendo .. senhor .. você pode fazer isso sozinho
Пікірлер: 367