That's impressive, well done all your hard work has paid off. Cheers, Poth.
@alexdyke194
6 сағат бұрын
Tom, you are gonna need a way to drain condensation from your tank if the tractor doesn't have a dryer on the compressor. Every time you cycle the system, you will get condensation from the expansion of the gas. If you don't have a drain in the tank, it will eventually rust out
@Tomlamb980
6 сағат бұрын
@@alexdyke194 it’s got a tap under the tank
@ianedwards9136
3 сағат бұрын
Coming along, glad the valves have arrived. I was working with a plumber/ gas fitter and he never uses that tape, he said best thing to use is the master plumbers/ gas fitters paste. Seals air / water / oil and gas, is pressure approved. Don't need heaps and 100% seals first time no worries. I never use the tape anymore and use paste on every fitting no matter if i am plumbing, working on vehicles.
@philipcounsell4709
6 сағат бұрын
Brilliant Tom, it will be interesting to see a manufacturer will pick up on this brilliantly simple system interesting their products . 👍👍
@Tomlamb980
6 сағат бұрын
Fingers crossed!
@SkyPilotXSX
3 сағат бұрын
Loving this series of vids! You need a new hat…. “Now we’re engineering!” 🤣 Loving the cheeky edit when you realized the isolation valve was the wrong way round and the lever wouldn’t open all the way 🤣
@robertellis8738
4 сағат бұрын
Brilliant!! , keep the videos coming Tom
@paulleaver8820
6 сағат бұрын
It looks like you have done a good job of it well done Tom
@memyselfandeye1234
4 сағат бұрын
Glad You Got Your Vales In The End .... Glad You Could Vent Of To... peace
@mattyod73
5 сағат бұрын
Hi Tom great idea . One thing that will help you with your leaks is fit two union fittings between the elbow and the inlet to the solenoid valve that will allow you to tighten everything before you fit the solenoid
@Lorddanielrushton371
7 сағат бұрын
Best idea since sliced bread. Great job Tom. Cheers
@Tomlamb980
7 сағат бұрын
Thanks 👍
@charleshart6992
8 сағат бұрын
Excellent Tom! Well worth the wait!!
@colbysquibb7854
8 сағат бұрын
Proper job mate.
@petergardner2334
7 сағат бұрын
it s a great idea
@garyevans8116
6 сағат бұрын
Is the powder getting moisture from the condensation from the compressor. If so you can get a moisture trap. I think that’s what it’s called. Great job Tom.
@stevewareing8525
8 сағат бұрын
Great video Tom, the blaster is getting there now you finally have right size fittings. 👍.
@Tomlamb980
8 сағат бұрын
Yes, thanks
@Downsviews1056
8 сағат бұрын
Hi folks 🎉 Hi Tom🎉 thanks your getting there. Great idea bet you have been mulling this over, and you now see some fruits of your developments. Hope, you get your drilling up together. 🎉🎉
@Tomlamb980
7 сағат бұрын
Not yet!
@jonathanjennings4232
6 сағат бұрын
Hi Tom, just wanted to check that you have fitted a safety relief valve on the air receiver to ensure it’s not going to be a time bomb should it go over pressure. Try using loctite 572 or 577 thread sealant instead of ptfe tape it’s much better on pipe work. A great idea to blow down the bailer
@Tomlamb980
6 сағат бұрын
The tractor controls the air flow it’s impossible to go above 115 psi
@jonathanjennings4232
6 сағат бұрын
@@Tomlamb980 Hi Tom I have worked on compressors / air receivers my whole working life and you can never trust a machine not to go over pressure, a simple valve can save a lot of problems, every air recovery in a system should have its own valve to protect it . I will get one sent up to you, we have them on the shelf.
@jonathanjennings4232
5 сағат бұрын
Just have a check for the design pressure on the air receiver it should be stamped on one end of the convex ends normally stamped WP with TP sometimes which will be the test pressure let me know the WP so we can match a valve to suit the pressure.
@saragayle2217
8 сағат бұрын
I could watch a whole video of you making things brilliant ❤
@Tomlamb980
8 сағат бұрын
Thank you so much 😀
@johngell4842
5 сағат бұрын
Top job Tom lamb now we are blasting 🤠
@tflemming287
4 сағат бұрын
On the nozzles as it spreads in one axis, it should narrow in the other. The current design just instantly reduces the pressure.
@timc7345
2 сағат бұрын
Hey Tom, you should patent that Bale Blaster, before someone else does mate!
@richardcanning7351
6 сағат бұрын
It’s looking good Tom. You’re doing well trying to work on this along with everything else. What about taking a line of the pressure gauge to connect to a second gauge in the cab that way you can see if you have to increase or decrease the flow into the tank. Has the cat signed the concrete yet? 😂
@peteb3365
47 минут бұрын
colins new potato cannon been developed 🥳🤣
@RobScarlett
7 сағат бұрын
What a great idea, love it.
@Tomlamb980
7 сағат бұрын
Thank you! 😊
@jakobrebeki
8 сағат бұрын
The answer to your thumbnail is YES. Even as a fire protection system it would be worth its weight in gold. Blowing the debris off the machine would be a bonus. Ever thought about using Halon for the fire system. Not to dear but discharge with care as it can kill you. Thanks for posting....
@StevenCasper
8 сағат бұрын
Beautiful. That's it. :)
@Tomlamb980
8 сағат бұрын
Glad you like it!
@stanislawsmykowski5850
9 сағат бұрын
First 😅 greetings from Poland. It rains here a lot lately
@Tomlamb980
9 сағат бұрын
Second
@stanislawsmykowski5850
8 сағат бұрын
@@Tomlamb980 thanks Tom for your work. I'm always glad to see, that You've posted som new staff. Deep down I'd love to be a farmer
@philapps3805
8 сағат бұрын
That was quick for UPS great idea the blaster try blasting bathroom scales to see how much force it produces at different psi in main tank
@thedudeabides8046
8 сағат бұрын
Bail blaster is genius, how about a scaled down version for the clearance of flattus! The pants blaster! windy wind removal! Proving yet again I too am guinness /genius...
@gardenogauge
8 сағат бұрын
@@thedudeabides8046 sounds like a project for Colin!!
@jongmassey
8 сағат бұрын
Careful now, a bad aim and you've got a ball blaster!
@ianhudsontlm
33 минут бұрын
I am really worried about this blaster. You are effectively building a bomb. Any failure of this equipment on the high pressure side will produce high velocity projectiles that could kill someone. There are so many connections and potential failure points. Be careful Tom, would hate for something bad to happen. You really need an additional pressure release valve in the system to ensure you don’t over pressure the system.
@cheechU38K
2 сағат бұрын
Tom X Furze = 🤘🏼🤓🤪
@SimonPerry-cz4ke
5 сағат бұрын
I thought Dave was organising the Concreting?
@gardenogauge
9 сағат бұрын
Swap your SOV and isolation valve around 🙂
@Tomlamb980
8 сағат бұрын
Thanks
@Piglife101
8 сағат бұрын
A little T joint with a train horn would be cool! 160psi would be mega
@Tomlamb980
8 сағат бұрын
You could if it ran a separate compressor
@bobcrawford2105
7 сағат бұрын
Tom I find if you use gas sealing tape instead of ptfe you get better seal on threaded couplings
@Tomlamb980
7 сағат бұрын
@@bobcrawford2105 thank you
@zjzozn
3 сағат бұрын
Will to hover like a jump jet?
@johannesvik3241
6 сағат бұрын
Good idea, but waste of time building a prototype in order to find out it doesn't work. You would need a ten times bigger air-tank to achieve what you want...or a gigantic air compressor.
@zebraforceone
8 сағат бұрын
I saw the picture of the solenoid this morning jesus christ lol Get an air horn on it
@GrahamWP58
6 сағат бұрын
Useless ...Paltry.... Service. Great test Tom
@philleeson7835
8 сағат бұрын
Will Dave the concrete cat fit up the pipe. How far would he bounce🐈⬛
@Tomlamb980
8 сағат бұрын
To the moon
@zjzozn
3 сағат бұрын
Tom’s BJ machine
@Virusviper
8 сағат бұрын
Unreliable Parcel Service, never fails always delivers... Eventually!
@flybywire5866
7 сағат бұрын
Today I watched a video of a John Deer combine burning down. As the reason, it was said the gear box for the drum overheated, starting a fire. This gearbox seems to be located under the plastic diesel tank. When the driver noticed the situation, it was already too late. In another video, the reason given was the same. There it was a lack of oil, leaking oil tube. These $500000 machines seem to have no $30 oil pressure or temperature sensor. Maybe the manufacturer can't afford how much the $30 sensor cuts into the profit. Well, for the manufacturer, it's win-win. Don't spend the money on the sensor, sell another combine. A cab full of monitors and no warning. These insanely expensive highly flammable machines have no fire detection and no fire suppression at all. Your invention seems quite desirable to have, at least to me.
@Tomlamb980
6 сағат бұрын
@@flybywire5866 thanks
@johnwarwick4105
4 сағат бұрын
Yes if a combine was running in industry, key components like that would be linked up to a simple temperature sensor. Very low cost and would trigger an alarm long before a fire could be started, may even save the gearbox as well. Common problem on the drum drive gearboxes oil seal fails and gearbox runs dry till something catches fire, crazy.
@bizzer999
8 сағат бұрын
c4yt
@adrianhutchin4925
4 сағат бұрын
What farming getting in the way of playing how rude 🤣🤣🤣
Пікірлер: 69