The battery indicator light on the dashboard of the Vaz 2109 carburetor is lit. Replacement of the generator's diode bridge. #repair,#remontsvoimirukami, #remontavto, #auto repair, # remontgenerator, #generatorvaz, #diodnyymost, #zamenadiodnomost.
Become a channel sponsor, Learn More:
/ @den_is
00:08
After starting the engine, the battery warning light does not go out.
00:16
I turn on the light, it lights up even brighter and burns, I turn on the stove, it burns even brighter.
00:29
I think this is a diode bridge on the generator, now I'll sort it out and see what's there.
00:37
We remove the terminal from the battery, pull out all the wires, unscrew the key for 10.
01: 05
Next, with the key on 17, we unscrew this nut and
01:33
with the key on the 19 here is this nut and pull out the bolt from there, stand on the side of this bolt.
01:52
We pull out the bolt, remove the generator belt.
02:02
We unscrew the adjustment plate of the generator further with the key on 13,
02:16
I have already ripped off the generator and pulled it out through the top.
02:45
The diode bridge has already been bought, I will change it, then I will unscrew the pulley with a key on 19.
03: 18
Unscrew the brushes, the condenser, so that it does not interfere with further disassembly,
03: 29
removed the brushes, in principle, they are still normal .
03:39
Then you need to unscrew the pulley.
03:47
We put the screwdriver so.
03:51
And unscrew the key to 19,
04:01
I tore off the nut.
04:03
unscrew it.
04:21
Unscrewed the nut.
04:25
I removed the pulley, it is made of two halves.
04:32
Here the key stands, it is not to lose the most important thing.
04:47
Here it is, it is rusted, I will not even sheburshit it, so as not to get lost.
04:59
Then I untwist these bolts, these studs, there is no one stud, there should be four at all.
05:23
Unscrew the bolts with the head for 10.
05:29
Then with gentle blows of the hammer
05:56
Removing the housing,
06:00
Removed this part, in the direction of it.
06:17
We will change the diode bridge.
06:21
Unscrew 3 nuts.
06:33
I unscrewed three nuts, they are on 8 and pull out the winding.
06:43
So here it all looks.
06:50
Then we take the needle and pull this contact out of the chip.
07:04
There we bend the plate, pressed it.
07:14
We remove the diode bridge, over there so firmly sits, stuck or something ).
08:08
That's what he is.
08:12
I pulled out the old diode bridge, here it is like this, and here is the same new one.
08:26
Now we put everything in reverse order, collect it.
08:31
Everything put it, there is a contact, it is necessary to bend this tongue and insert it into the chip.
09:14
Then we collect, put the winding.
09:23
Then I'll show you what happened .
09:26
I collected everything, screwed the winding down
09:30
So that's how it looks.
09:36
I will continue to lubricate the bearings, this anchor is already, the production at the anchor is strong.
10:02
We pry the duster with a needle, remove it and hammer in the lubricants there
10:38
I filled the grease in the bearing, then put the anther, all the anther fell into place.
10:57
Then we unscrew these four nuts and remove this cover.
11:12
Unscrewed the nuts, remove this plate, then this washer.
11:37
We pry the duster with a needle
11:56
That's it, I took off my duster
12:03
Now I'll put the grease in there, put the duster in place.
12:17
I filled the grease in the bearing, now I will put the duster.
12:26
All the duster is in place, we wipe it further and assemble the generator.
12:41
Screwed on the bearing cover, the one who will change the bearing,
12: 49 it
is desirable to have a key in stock, sometimes it does not pull out, you pull it out and it breaks.
13:04
It is necessary to have a spare key when replacing the bearing and when replacing the anchor.
13:13
Then we put it all in place.
13:21
The hole matches all exactly.
13:37
Then we put these pins here, twist them.
13:44
All twisted the hairpins, then check,
13: 50 so
that the wiring does not touch the rotor, turn it around and see what is there.
14:00
Then we put the brushes.
14:16
We tighten the bolts, two bolts 1, 2.
14:51
We put this chip here in the brushes.
15:03
Then we stretch everything out.
15:13
Stretched all the bolts of the nut.
15:15
Then we will put the pulley.
15:32
We put the blade, the pulley.
15:53
We tighten it further in the same way, put the screwdriver here so that it stands up well and tighten the nut.
16:10
Everything was spun by the pulley.
16:14
Such a generator is 14 volts 55 amps
16:40
Then I will put it on, we will see what happened.
16:44
All the generator screwed, all assembled.
17:34
All the light bulb went out, the light turned on,
17: 38
nothing is burning no light bulb, the stove is turned on, nothing is burning.
18:26
All the generator is working , everything is fine.
18:34
That's all, the video for repairing the generator is finished, put the likes,
18:47
BYE, EVERYONE !!!
Негізгі бет Тәжірибелік нұсқаулар және стиль The battery warning light is on. Replacement of the Vaz 2109 diode bridge .
Пікірлер: 80