You do NOT need to dual feed these carbs if you block the crossover. There is a crossover in the airhorn that feeds the far side needle as well. If there werent you'd only ever need to adjust the near side float in single feed applications.
@MarcBchannel
Жыл бұрын
Really good video👍Ive heard you can make these carbs work really well with these simple mods. If only the bowl vents were higher. Then it mite be the perfect off road carb. Running an adjustable pressure regulator down low while off road mite help too but may not be necessary. Good job bud👍
@diveingarage
Жыл бұрын
Thanks! Hmm good idea on the fuel pressure. Might be good for what I'm doing too.. something Ill think about for sure.
@dougj.8288
Жыл бұрын
When the video started I was hoping you were going to get that crossover, i actually used JB weld.
@diveingarage
Жыл бұрын
Oh yea! Got to! I thought about jb weld, but heard it will still dissolve over time. How's yours holding up?
@dougj.8288
Жыл бұрын
I’ve done it a couple times, I ran one truck that way for a couple years with no issues.
@DesertHack
Ай бұрын
can you show what the fuel bowl crossover block off with fuel line looks like and how to do it best?
@chrisadkins602
29 күн бұрын
You literally just take a small piece of fuel line and wedge it in the middle of the crossover with the hole oriented up. Cut it long enough that it protrudes above the top of the float bowl about 1/32" to 1/16" and install the airhorn as you normally would.
@diveingarage
29 күн бұрын
Next time I get another Edelbrock carb I'll show it.
@armygreenfj3924
6 ай бұрын
Planning on taking my k5 to the rubicon. I’m still running a carburetor that’s properly tuned with a wideband gauge. Hopefully these mods will work if not I’ll probably go efi.
@diveingarage
6 ай бұрын
These should help for sure! Make sure your regulator is working, offroading psi is different than street
@armygreenfj3924
6 ай бұрын
@@diveingarage what should I set it at for off roading? It’s currently at 5.5psi
@diveingarage
6 ай бұрын
If you're running the stock style needles turn it down a few psi. If you upgrade to the offroad needles you might be ok at 5.5. Just experiment!
@JeremyFrazelle-or1mt
6 ай бұрын
How does sealing off that passage effect the carb under hard throttle with a dual feed line? I would think it would starve the engine eventually… Correct me if I’m wrong.
@diveingarage
6 ай бұрын
Once you set up a dual feed you don't need that crossover anymore. So each line will fill one bowl and keep it full.
@chrisadkins602
29 күн бұрын
Even without dual feed the crossover isn't doing much. Most of the fuel is flowing through the passage in the airhorn and going through the far side needle anyway.
@dimitrisfegos1481
6 ай бұрын
Hello the same mods work as well at 1404 500cfm carb.... Is better to buy avs2??
@diveingarage
6 ай бұрын
Yes the avs2 is better
@christopherpoucher483
9 ай бұрын
Lol the rail feeds both sides anyways
@diveingarage
9 ай бұрын
Right! It's the crossover you want to block for this
@_Otaku-kt8be
Жыл бұрын
Best carb mod is throwing it in the trash and installing efi 😂
@diveingarage
Жыл бұрын
No efi for this build! That's a whole bag of worms
Пікірлер: 26