I have antique cast iron bed with years of paint. I’m definitely gonna try THIS! Good video. Thx!
@championplayerdo7604
7 ай бұрын
Now that was a great video! I had bought a needle scalar nearly 2 decades or so ago and never used it! Didn't really know how to use it or what applications it was really for I was just accumulating tools I figured I would need at some point like I've allways done. But I have to admit this was a great video! And so now I am informed
@JeremiahL
7 ай бұрын
Glad you enjoyed it. I plan on doing some more tool reviews. Subscribe so you don't miss it.
@mikehilbig8280
14 күн бұрын
Use hearing protection. Needle scalerse will deafen you, quickly.
@G5Hohn
Жыл бұрын
Needle scalers are for- get this- thick SCALE. Like rust so thick you can’t really tell how thick it is or if there’s any metal left underneath. It’s absolutely the *wrong* tool for paint stripping or light rust removal. Get a scotch surface conditioner roll and go to town with that- way faster and more efficient for light rust.
@JeremiahL
Жыл бұрын
you sound very confident in your position. I recognize that it's possible that you have never used this tool for this application, or seen it used for paint removal, but my recommendation is that you do a quick search. I think you will find that not only are needle scalers used for paint removal, but they are widely prescribed specifically as the solution for leaded paint removal...
@JeremiahL
Жыл бұрын
Let me help you . www.osha.gov/laws-regs/standardinterpretations/1991-06-18. Let me know if you need more objective evidence. Thank you for the comment
@G5Hohn
Жыл бұрын
@@JeremiahL I apologize for overstating my point. Instead of saying they are the wrong tool, I should have said there are better choices in tools for the task depicted. Obviously they will *work* but then again, one could do dental work with a Dewalt drill technically.
@JeremiahL
Жыл бұрын
@@G5Hohn Cheers to that
@littled6698
9 ай бұрын
Yeah, scaling that first piece of NEW metal isn't what this is for. Look at the condition of that metal now. It is all "dented" up. You don't needle scale threads on a pipe fitting either.
@randyb3347
Жыл бұрын
Did I miss something? What happened to the motor you were going to strip?
@JeremiahL
Жыл бұрын
This was just the tool review. I have a restoration video coming up where I rebuild my jointer. Cheers
@justinpaone2227
Жыл бұрын
mine lasted 6 hours of use. and it's so tight i can't get it apart with a 3 foot bar to inspect it/clean it.
@JeremiahL
Жыл бұрын
Did the cup that hold the needles get compacted?
@justinpaone2227
Жыл бұрын
@@JeremiahL the cup is fine. i got the jam nut loose, but can't breakloose the actual tool so i can clean it up if it's got any rust anywere. i used it last week. i got a replacement today at harbor freight. i oil the tool more than i should. either something broke or I need an air dryer. i'm sure i need an air dryer however i have a dozen air tools and this is the only one i've had in 20 years that failed.
@JeremiahL
Жыл бұрын
@@justinpaone2227 ill follow up if I have any problems.
@littled6698
9 ай бұрын
@@justinpaone2227You don't need to torque the pieces together. Loose is fine. The needles will break with use, and I've had the little "head" of the needle boubce around inside and need to be taken out. Also, too much oil is a good thing on needle scalers.
@Zooooom01
8 ай бұрын
Takes petrified undercoat off E-Z
@dognatious6153
Жыл бұрын
Scew that. Id just use a multi-tool. Faster, easier to mive around.
Пікірлер: 21