Personally i think ALL of the mainstream manufacturers SHOULD include paint masks as standard anyway
@Mishn0
3 ай бұрын
And then you'd complain about "kits are so expensive now!"
@jaws848
3 ай бұрын
@Mishn0 no i would NOT....at the end of the day masking tape costs almost nothing to make and if kit companies dont include it then you would have to get it somewhere else so EITHER way you STILL have to pay for it.
@Mishn0
3 ай бұрын
@@jaws848 The time it takes to design a mask isn't free, making a die to cut the mask isn't free, the material used to make the mask isn't free, the extra time to handle and pack the mask isn't free. It's up to the marketing department of a company to figure out if the extra cost to provide a mask affects their sales negatively or positively and to decide whether it's worth it. You're free to suggest or DEMAND that they do it, but whether they do it or not is up to them.
@Jason_L10
3 ай бұрын
@@Mishn0 However if a kit manufacturer has a major advantage when it comes to making masks, they already have the dimensions of the mask parts, due to the parts all being in the CAD system, and a therefore at least a couple of steps ahead of the likes of Art Scale Kit, etc. Creating the cutting die, and entering into the cycle of fit, adjust, refit is a lot quicker. Costs would be kept down as they will get massive economies of scale, when they are producing 100,000 units, compared to ASK who maybe produce an initial run of a couple of 100 units, so the price differentials would be minimal impact. the only way to truly find out is to crunch the numbers and produce a couple of kits with masks included and see if people buy them at the revised price.
@anthonyjones5444
3 ай бұрын
PE no, it’s redundant these days. Masks yes, on the basis that they didn’t add substantial cost because in my opinion Airfix kits are in general not competitively priced compared to many other manufacturers.
@ronandanne1
3 ай бұрын
I'd like to at least see seated pilot figures in all aircraft kits
@hillaryconstable4283
3 ай бұрын
Masks yes, photo etch no
@davepasopton8840
3 ай бұрын
Great question Jason. Personally I would say yes to Masks, especially in kits with less-than simple glazing. This can help the learning modellers to achieve a better result than being disheartened by the jeopardy of time consuming attempts with tape,knife and or messy masking fluids. Photo etch - no, this is an expense only for those who feel they want that level of detail and challenge. As another suggestion alongside that, maybe there should be a new accessory product line for Airfix to offer:- a package for each aircraft with scale accurate and authentic crew figures along with a suitable flying support stand rather than some of the varied offerings previously. 😊
@markmacdonald9216
3 ай бұрын
Yes. I would pay more for masks and etch.
@jaws848
3 ай бұрын
Not too concerned about etch as i dont bother with it but as far as masks go yes i would IF they are of good quality AND IF they fit properly
@jeffholt9437
3 ай бұрын
Yes to paint masks but, let's be honest, how much extra would (or should that be "should"?) this add to the price? No to etch.
@AndrewTownsend-x3r
3 ай бұрын
Yes definitely Airfix should include at least paint masks and seatbelts
@JohnSmith-qk4le
3 ай бұрын
Masks yes photo etch no, too fiddly for me, but an interesting subject!!
@markrichardson6071
3 ай бұрын
Im not bothered about PE , but would definitely be prepared to pay extra for canopy masks. Thanks for the video. 👍
@leefennell
3 ай бұрын
Good-quality masks should be standard in all kits. If Airfix can negotiate with Cartograf for their excellent decals, they could easily do a deal with the likes of Montex or ASK, for example.
@MichaelSwan-p4z
3 ай бұрын
Masks yes, etch...can't stand it.
@BradSGP
3 ай бұрын
Great topic and concept Jason... I think Masks would be a good idea in any scale , and really should be standard these days... but etch, and possibly resin, would be an idea for larger scale kits (1/48 and above) as a "master" version at the premium price... Would be happy to pay for that
@jerryclulee8127
3 ай бұрын
I would like to have the option to buy a kit with extra detail parts. I sometimes get tired of searching the aftermarket world.
@nsewerin
3 ай бұрын
Hi Jason. Good question for a first timer. For me it's a resounding yes, I'm willing to pay more for the model itself if Airfix added PE, Masking and 3d printed part, as I almost always find extras for my models. But there are always some model builders out there who want the opposite attitude and want to build out all the extras and want to keep their expenses on their hobby down. In reality, I think it's good what Airfix is doing, keeping the price down on the kits with recently nicely detailed plastic and an opportunity for each individual modeler to judge for themselves whether they want to buy in the extra. (I like that flexibility)
@stuart-xt3jo
3 ай бұрын
as a new modeller i think a mask set would be a good idea but the thought of photo etch is a bit daunting dont know if i would pay more for the PE as would probably not use it .
@Gremlins_Modelling_Mayhem
3 ай бұрын
I possibly would pay more if they included mask sets and maybe 3d resin parts.
@ianpettman7482
3 ай бұрын
Yes I would pay more for paint masks and PE harness parts.
@gorlestondoug
3 ай бұрын
Canopy masks should be standard in my opinion, as for PE perhaps a deluxe version would be the way to go.
@franktozier3184
3 ай бұрын
I would pay a little more for a kit if it had paint masks. PE is a maybe. The PE would have to enchance the model.
@johnmarley6695
3 ай бұрын
I find myself buying improvements whenever I can. Canopy masks are always useful and I’ll add PE if I think it’ll be fun fitting it. Canopy masks are a definite help for Airfix’s B-17 kit. I chose to purchase photoetch for their Chipmunk kit but it can’t be seen. Seatbelts are visible, though. I’ve purchased interior photoetch for both the Vulcan and Victor because I’ll enjoy the process knowing full well it won’t be seen. So…Yes. I’ll continue to purchase Airfix kits and add masks later.
@MarcvanExel
3 ай бұрын
I think it would be fantastic if they offer the option. Like what Eduard does with their weekend edition without any etch/masking and the profiPack that includes all those goodies. I usually buy the profiPack if I have the option but if I buy form another manufacturer that doesn't provide those extra's with the kit, I do not allways look for those aftermarket extra's.
@aberration3869
3 ай бұрын
My two cents are I’d rather not have the extras if it means a higher cost. I could see wanting and adding it on the open cockpit of a WW1 plane for instance but really on anything else it’s just more of a exercise for the satisfaction of knowing it’s there rather than being a part of the display. The B-17 for instance, I spent a lot of time doing things no one else will ever see. Now they weren’t “extra” parts and I did enjoy the process, I even scratch built some oxygen canisters to disperse around the interior but no one will ever see them. So no, the basic kit please for as economical as possible and let the fanatics buy the detail sets at their choice.
@bernhardkunz3392
3 ай бұрын
Airfix should do it like Eduard did it. Release Profi -and Standard-Versions of the kits. That has the effect, that as a modeller, you still have the choice, but probably most people go for the profi-Editions, which becomes after time the sort of accepted "standard-version", in a higher price-category. It is better to lift up the buyers in a higher, accepted price category than giving people no choice with only upgraded kits, and probably exclude a reasonable part of them as buyers.
@lesthiele4921
3 ай бұрын
Hi Jason, you may have opebed the flood gates on this subject, if I wanted the kit I would say yes to PE and paint masks, but do we really need them and I think the answer is NO, as for PE, the only thing is would want for aircraft is seatbelts/ harnesses, and maybe masks for just the canopy, well that is my opinion, bedt regards from a Kiwi living in Australia, Les
@colinhenry3551
3 ай бұрын
Hi Jason, Personally I wouldn't mind paying a little more for the extras,if I was sourcing aftermarket from elsewhere ,maybe 2 or more suppliers there is the factor of postage and packing which these days adds quite a percentage to the items ,unless you spend much more than you really want on other stuff like another kit to great free postage ,MORE Stash ! 😂
@GavinNerazzurri
3 ай бұрын
It doesn't make any sense. Why should some people pay more for things they won't use, when the items are already available for the people who do want to spend more. The question is moot anyway - Airfix know their audience.
@Jason_L10
3 ай бұрын
It all depends on how much the price increase was compared to other aftermarket solutions, what about the HGW type Seatbelts. In regards to the Seatbelts, Airfix would have to provide 2 seats, one with and one without seatbelts cast in order to cover both options. Photo etch can be over done, yet it allows some fine detail but often its actually overdone, for example the Meng Pather 171. AusF G has a lot of Photo etch half of which is unused depending on the variant being built.
@Makkaravuori
3 ай бұрын
No. I want to decide what extras I want to get, depending on the kit. I dont want to pay extra for the included extras that I dont want or need.
@cnfuzz
3 ай бұрын
Not if it was the upteenth spitfire, but for masks why not, i rather have them release interesting subjects
@eteocles4452
3 ай бұрын
Easy solution. Do two kits, base kit and a limited edition deluxe kit with added upgrades. The deluxe kit could be an Airfix shop exclusive to make it easier to track sales to see if it is worthwhile or how many to produce.
@DanielWarren-ci8pq
3 ай бұрын
Good question and I can see both sides of the discussion but I'm going to go with the 'no extras' option. As many people have said already, some modellers - particularly people starting or, like me, getting back into modelling after many years, won't necessarily be concerned about the extras. Some things like etch will only complicate things and, when it comes to it, the most important thing to many people might be price to enable them to continue with the hobby. Anyone wishing to buy the extras can go to the aftermarket as they do at the moment.
@jeff72_
3 ай бұрын
Interesting question and I do feel Airfix are missing a trick by not including aftermarket options such as paint masks and seat harnesses as standard in some of their inventory. I do understand that on a per item cost basis it may not make sense to include masks and harnesses in each kit but it would make sense in the series 2, 3 or 4 kits etc. Yes it would cost a little extra but that is offset whereby the modeller will want/need paint masks and harnesses and will incur additional cost to get them (item cost and P&P). Arma Hobby have a good approach to this where you can buy a basic boxing of the kit or a detailed up version with aftermarket included or you can level up again and add additional aftermarket such as 3D printed parts or resin. Again, Airfix are missing a trick by not including paint masks or seat harnesses as a minimum in their series 2/3 and above kits.
@JeffDonahueScaleModeling
3 ай бұрын
Hi Jason, Great question. There are no easy answers to this. There are so many modelers with such varied skill levels. It's going to be impossible to have one kit that makes everyone happy. It would be an inventory nightmare for manufacturers to have several variations on every kit to accommodate everyone. For me personally, I like the extras, PE, Resin, etc. I don't mind paying a little more to have those included in a kit. Of course there are a lot of people that hate PE and Resin and being forced to buy a kit that includes them probably isn't going to happen. Paint masks are a good idea for some kits as long as they are of a good quality. Have a great day. Jeff
@george_364
3 ай бұрын
I can very well imagine that people building models on KZitem, and those following and interactinng on the Modelkit Stuff channel and other channels here are not the average modeller. And that they are more into super details, photo etch etcetera than the average consumer.
@martinwalton2850
3 ай бұрын
I do think that Airfix need to explore these things at least. It strikes me that they do a lot of research to make the plastic as accurate as it can be, so why not embrace other technologies to apply these data to? Other manufacturers have two levels of kit if you want to upgrade so this may be a good way of upselling for Airfix as well as not being left behind in the 3D resin printing movement. That element isn’t going away and could significantly impact on their sales in areas. Why not partner with smaller manufacturers to offer a bundle?
@plasticmonkey5594
3 ай бұрын
I think maybe if they done 1kit basic. And another one with the option would be a good idea then would capture both markets.
@michaelpotter4425
3 ай бұрын
Maybe have a box A or box B of the same kit as if you're starting out you have to spend a lot more on the extra stuff you will need like super glue for the resin parts or the tools to bend the PE might not sound a lot but even starter kits are not pocket money any more I think we all love watching people modeling and the high standards you and others get but most people it's just a hobby or an escape from the real world keep the great vids coming enjoy
@Jason_L10
3 ай бұрын
good idea, or vary it depending on the skill level of the kit, eg levels 1-2 no extras, level 3 introduce paint masks, level 4 add basic PE/seat belts, and Level 5 throw in all the belts and whistles.
@niyazali7983
3 ай бұрын
I think they could do it, but label them as higher level kits (said as someone who still doesn't know where to get decent extra details).
@jeffpeterson6094
3 ай бұрын
I hear ya... but i think leave it alone
@thetoon50
3 ай бұрын
Definitely yes
@Johnny-tt8zc
3 ай бұрын
I think every manufacturer should include masks as standard. And not like the tamiya ones where you have to cut them out.
@jeffholt9437
3 ай бұрын
TBH, even self cut ones (at NO extra cost) would be something.....
@philiphirst1310
3 ай бұрын
Yes
@stevelamb5760
3 ай бұрын
yes
@captaincharlemagne
3 ай бұрын
I would definitely like paint masks in a kit the photo etching parts depending on how fusy they can be to put on I would definitely like in the kit as well. I am not above paying a little extra for a kit if all the stuff comes with it as I know that it will be put to good use
@brenstratters2026
3 ай бұрын
No, You have to remember Airfix kits are made for ALL. If you wish to detail up your model go get the aftermarket. You would take the kits out of the reach of children and those who do not wish to/or cannot deal with fiddly bits of metal.
@azzaob510
3 ай бұрын
I think I remember Dale [Airfix] saying in an interview that incl photo-etch would restrict it to over 14year olds, and that was the reason why they didn't go that route [could be wrong]? i.e. restrict their sales?
@DropdudeJohn
3 ай бұрын
I'm 56 and I'm back int the category of having trouble dealing with fiddley bits of metal, chunky fingers, dodgy eyes.
@ModelkitStuff
3 ай бұрын
No that is correct Photo etch is considered sharp which is why almost all manufacturers have 14+ on thier kits
@jeffholt9437
3 ай бұрын
You can still brush paint with paint masks.....
@phil9884
3 ай бұрын
Yes Yes Yes. I tell Airfix at every show. One day they might listen. The power of nagging😅.
@jeffholt9437
3 ай бұрын
I use every opportunity to push for a 1/48 Angel Interceptor or plastic Stingray Submarine kit so, regarding perseverance , let's hope so!!!!
@carlsmoot2939
3 ай бұрын
I think there might be a bit more to this. The extra items you mention really fall into different categories. Masks are a time saver and because they can be easily made from the drawings Airfix uses to produce the kit, they will fit better and would be available five or ten years from now assuming the kit itself is available. Aftermarket masks may or may not be available in later years. And there is no doubt that masks are useful especially on kits with complex canopy framing. Masks, if available, will almost always get used by the modeler. So masks, yes. Seat belts, and other details, PE, 3D printed, or resin all fall into the "Next Level" category, meaning that they may get used, and in many cases, not used. This means that for many modelers, they are simply an added expense. There is also the added research, product development, and testing that would go into adding these items. Where Airfix, and other manufacturers could probably better traditional aftermarket manufacturers is in economy of scale meaning that they could offer these items separately for a lower cost. An alternative, to keep costs down, or perhaps instead, as an additional revenue stream, would be making the files available to 3D print the parts. So for including finer detail parts, probably no, at least in the generally available kit. There are a few other forms of "Extras", if you will, that might fall into this debate. Pilots, for example. I think these should be included, but only in a way that doesn't compromise the molded in detail. In other words, cockpits that do not sacrifice molded in detail simply to make it possible to fit in the pilot. Instead, make the pilot figure in a way that allows them to be used more easily (i.e. separate legs, arms, heads). There would be extra cost associated with this, so it's a toss up, but I believe many modelers would prefer to have pilots rather than not. Weighted wheels, only if non-weighted wheels are also included. Landing gear doors that fit in the openings for those who prefer in flight displays. Yes, please include these, or better yet, make them work with both up and down landing gear approaches. Riveting, is a tougher question to answer, and probably too deep of a subject to include in this debate, since solutions that I can think of would either be expensive or potentially turn off sales to some modelers if not included, especially if another manufacturer offers a similar quality kit that does offer riveting. As a possible, middle ground solution, maybe include the rivet patterns as scaled drawings (or files that can be downloaded) so that those who want them can reproduce them more easily. As I said, a deeper discussion than what is suitable for this debate. And finally, also probably a deeper discussion item, the inclusion of extra detail in the form of gun bays, engines that would not be seen (I.e. inline piston or completely buried jet engines), and other similar detail. I personally think these could be offered in a separate, more advanced kit, leaving the more basic kit for those who don't need them. I suppose it depends upon the economy of producing these. Eduard's approach to this is to include all the parts in the same moldings since its probably cheaper to include them than to have to produce separate sprue trees for a smaller subset of kits. Enough, as this comment went on far longer than it was intended.
@jeffholt9437
3 ай бұрын
You've been thinking about this for a while haven't you - I can tell! 😊😊😊
@carlsmoot2939
3 ай бұрын
Yeah, I tend to go overboard on these sorts of things! 😀😀
@ModelkitStuff
3 ай бұрын
some very interesting points, thanks
@iancarlin4694
2 ай бұрын
I believe Eduard have it correct. Weekend edition without PE or masks, profipak with frills at higher cost. Would love to see Airfix do the same and give customers option. I would plump for the extras option.
@ModelkitStuff
2 ай бұрын
There is a third option, I believe is better look out for the conclusions on Monday
@toboldlygosmodelworks1973
3 ай бұрын
No - it means your pushing Airfix out of their Age range - 8 years + to 14 years +, most people prefer to make their own.
@jeffholt9437
3 ай бұрын
Paint masks wouldn't exclude anyone - cheap as, well, paper (I would have said "chips" but that's not true anymore!) and can be used with brush painting.
@BlackBart33
3 ай бұрын
Hi Jason, I like the new 'Big Debate'. Very interesting reading through the comments. For me, I do like kits that have the likes of a mask set and any other bits added but it is far from essential. Also I think a lot of aftermarket manufacturers rely on us more experienced modelers picking up their products and if big companies like Airfix started putting these things in the kits it would have a major effect on them. I also like the Eduard approach with the Weekend editions giving you everything you need to make a lovely model then the Profipack for added detail. Interested to see what the debate shows. All the best for now.
@ModelkitStuff
3 ай бұрын
Glad you the new series
@DropdudeJohn
3 ай бұрын
1/48th and above then yes, but would be good if they went weekend and profipack like certain other manufacturers, but as their are plenty of third party companies doing the extras already then it might be a bit pointless for Airfix to do it themselves Thing is if if you want to pay more of it you can already, you just but from a different manufacturer, I think Airfix know their market and straying into others territory probably just isn't worth it.
@DropdudeJohn
3 ай бұрын
Now its got a heart I have to leave the typos in, no rescribing for me
@kkirkcaldy
3 ай бұрын
Personally I think Airfix have got it right by not including masks and seat harnesses. I (nearly) always add aftermarket to my kits, but I don’t always use the same manufacturer, and I very rarely use aftermarket paint masks. I think it is better for the customer to be able to make their own choices regarding this, and by keeping this out of the Airfix kits it keeps the cost of a kit down. Plus, it won’t put a newer modeller off building the kit, should they choose to buy a kit that has the extras included.
@jeffholt9437
3 ай бұрын
What choice do you need for paint masks? As someone has already commented, the CAD files should already provide the perfect dimensions- as long as the quality is right.....?
@Dg-vg9fw
3 ай бұрын
I think giving the after market as an extra,like the new lifeboat kit has decals to personalise the kit is the way to go.Putting the price up may scare of beginners/youngsters and we want to encourage more into the hobby.Yes Airfix should do more but as an extra.
@michaelcox7564
3 ай бұрын
There is a third option to this discussion, supply photo etch with some kits but not others i.e. a premium kit, there by there would be a kit with extras and without extras, the choice would be up to the modeler. I would buy a model Kit with Photo etch, but if it is from Airfix they will need to improve their research. I have recently brought a ship model, H M S Devonshire a group one G.M.D the kit was actually a Group 2 Guided Missile Destroyer, as for the ships boats they too where different from those carried by G M D's. If this is the quality of their research it is pointless spending the extra money on supplied photo etch. In the main though I would rather have Photo etch in a kit and would pay more for some.
@ModelkitStuff
3 ай бұрын
I think the ship comparison is a little unfair as its a very old kit and nothing like thier modern releases, they now use 3d scanning technology to get perfect accuracy.
@jaws848
3 ай бұрын
@ModelkitStuff after all these years i FINALLY bought my 1st 1/48 kit.....the Heller Fouga Magister along with the aftermarket Irish Air Corps decals for it from Max Decals
@ModeratUlf
2 ай бұрын
I think that Airfix could do like Eduard and have a "weekend" version without PE and masks, and one "profi" version.
@JAFKARNAT
3 ай бұрын
Masks should be standard for the pricier models.
@adm65260
3 ай бұрын
armour hobby showed the way , put mask templates in the instructions. 3d printed parts would elevate a lot of old kits and give new ones an edge.
@ModelkitStuff
3 ай бұрын
I love the idea of adding 3D parts to vintage classics
@adm65260
3 ай бұрын
@@ModelkitStuff I have often wondered if Airfix would ever re-CAD all thier classics , inluding those that the molds are missing and re-release them as 3D prints . Vastly cheaper than producing new molds , they could have partners , who would do the printing. I would certainly give it a go .
@markoldreive
2 ай бұрын
Interesting topic. Many of the kits I buy come with extras. Paint masks, photo etch, resin and other stuff. I personally would pay more for the inclusion of aftermarket add-ons. I am aware though that many don’t want these. I think a listing of addon parts would be better, so a basic add on would be paint masks, another would be paint masks and pe belts and harnesses and so on. This would allow people to customise to a level they are willing to pay. Airfix could either get these produced and marked with their own branding or they could approach current aftermarket like Eduard , and give them early access to anew kit. They could then buy the parts from Eduard and either add to the model box or come in its own packaging. They can approach others for mask resin and 3D as they want. My thoughts on this.
@DarrellThompson47
3 ай бұрын
I would pay extra for PE if it was just a few essential bit, so seat belts and mesh intake grills etc. As for masks, although I do buy them for some kits, especially if they have lots of glazing, I do get a little disappointed with the fit sometimes and end up do some of it myself. So if the masks are a good fit then yes I would pay extra for an aircraft with extensive glazing.
@palamj2
3 ай бұрын
I absolutely hate photo-etch and masking is lazy, so NO.
@jeffholt9437
3 ай бұрын
I use paint masks and spend the time saved restoring the ceiling of the Sistine Chapel but hey, you can call me lazy if you wish. BTW, try your next model with one hand tied behind your back as you obviously like doing it the hard way?
@palamj2
3 ай бұрын
@@jeffholt9437 it’s more I think I’m lazy and here in Australia the masks are expensive for what they are. I think 30 years of using Tamiya masking tape on canopies has probably made me follow a routine. I will admit I did use masks once on a MC200 1/48 and it was great but again cost.
@DarrellThompson47
3 ай бұрын
If you've got a whole extra day to waste on masking a kit like a Ki-21 then go for it. Others would like to use a mask set, that's not lazy at all. There's a clear difference between laziness and a time saver.
@george_364
2 ай бұрын
I wouldn't mind the extra cost of canopy masks for some kits where the canopies are complicated. I would not want to pay extra for photo etch on aircraft or tanks, maybe for some ships. Seatbelts or similar should be included in the decals. and for those who don't like those the aftermarket can provide photo etch or whatever better method.
@davidparry5479
3 ай бұрын
Yes I would cause the ambulance they made had photo etch and yes I would py more if they added paint masks and photo etch with their kits
@greybeardmodels
3 ай бұрын
It's an interesting question Jason. I don't think it's a straightforward yes or no. So, I've had to sit here for an hour or so, trying to formulate an opinion. For me, it depends on the kit/model/scale and my plans for displaying the kit. I would pay more for the kit if there were "aftermarket type" parts, as I tend to like to add details. For aircraft kits, I will source aftermarket mask sets as a given. I think that would be a great addition for painting cockpit canopies. As for the addition of PE? I'm not so sure. Resin parts, maybe? Thanks for earworm Jason, I'm going to be thinking about this all day!!!🤔😄 Cheers Bob 👍
@bushranger900
3 ай бұрын
Case in point regarding my comment last week Jason, regarding the intake cones for your Chinook build ie. the intake cones was a perfect opportunity for Airfix to round out that great model (for me at least). On the other hand one could just buy / find said "grills" from a stash of pe. I have not gone near an airfix model since the 80/90s so your reviews are important as whether I should even consider so thank you for your valuable videos.
@chrisberridge1346
3 ай бұрын
I believe that Airfix are now a quality precision supplier of excellent kits with great detail but I think they should provide an option like Eduard with their weekend or profipack and Revell with their standard or the premium edition on some kits so that a modeller can decide how much he wants to pay primarily and how far they want to go with detail. Great topic Jason. All the best 👍
@micksmallwood487
3 ай бұрын
G’day Jason, yes I would pay a few extra $ for masks and harnesses as I look for aftermarket for kits I buy now, particularly canopy masks. Would have to be cheaper as a bundle than separate aftermarket.
@PennysPitstop
3 ай бұрын
Simple answer no. I like having the choice. Some masks I just don't need. A simple cockpit mask can be made with masking tape, a sharp blade and a little patience, why should I pay extra for that. In most cases seat belts can be made easily, however some kits are more complex. I like the current system where a satisfactory kit can be made out of the box but for those that require a little bit extra aftermarket is available. However there is a couple of options I'd go for. Mini art just brought out a kit in two sets, a basic and an advanced. That gives buyers a choice. Even if the aftermarket was offered by the kit manufacturer or, for example, airfix brought out a "rivet counter" edition of a kit that would be great as long as the basic is available. Can you imagine airfix bringing out three versions of, let's say, a spitfire. The starter/gift edition, intermediate version and the river counter (sorry, advanced) edition.
@PennysPitstop
3 ай бұрын
I think the point I'm trying to make is that while it's basically a good idea, I hate paying for something I either don't want or can scratch build myself with little or no effort.
@jeffholt9437
3 ай бұрын
@@PennysPitstopI guess paying for those extra decal options you don't use must be a real bummer?! Seriously, I'd agree that masks for a WW1 biplane would be an extravagance but how about a HE111 or other similar bomber - or commercial airliner for that matter?
@PennysPitstop
3 ай бұрын
@jeffholt9437 it really depends on the model, which is why unboxing videos are so valuable along with scalemates. I dont mind paying for things I'll use but buying a mask for a square cockpit, or buying seatbelts for a model with a closed canopy is a waste imo. I recently started the airfix tiger moth and felt the need to buy seatbelts, but most of the time I wouldn't bother as I can make a simple strap out of masking tape and a sim0le buckle from a piece of wire
@jeffholt9437
3 ай бұрын
@@PennysPitstop Boy, you must build a lot of 109s !!!
Пікірлер: 103