Great, very useful video. You definitely deserve more attention than that!
@118Wilson
3 жыл бұрын
How do you keep track of where everything goes
@fusiondew
3 ай бұрын
Generally by numbering things like valves, pistons, rings, etc and knowing the anatomy. With cars we usually will have a bunch of sandwich bags with painters tape on them to write on with sharpie. Everything you took out of cylinder 1 goes in the cylinder 1 bag and so on. Bolts and stuff I’ll usually thread back into the hole a little bit if it’s convenient, otherwise harbor freight has magnetic tool trays for $1 a piece, or more sandwich bags.
@BrianDesmond-bp1rk
5 ай бұрын
Could you help I’ve got a 2001 yz250f I have a decom lever an I disconnect it at the top of the engine an reconnected it went to kick it. It’s like the decom lever is stuck on Bike has 30/100% compression
@wyattcitizenzap4539
4 ай бұрын
you earned my sub. you are a very well spoken.
@ps.adv.9851
3 жыл бұрын
Very good videos. Thanks for all your effort. I know it takes hours and hours of work to get these videos done. We'll done!!?
@lukesancasciani
5 ай бұрын
Hi how would you proceed dismantling the engine if the piston is stuck and you can’t put it on TDC?
@findvoltage
3 жыл бұрын
Where is the link for the leakdown gauge tool?
@Kdjoao
2 жыл бұрын
How you remove the sprocket so easily. I was struggling for days. Anyways your video is very high quality
@ducaduke
2 жыл бұрын
Haven’t even started this video but wanted to thumbs up and share. Thank you for your hard work it’s so fucking appreciated. Love you
@donatusgiger9871
Жыл бұрын
what should I do if I cant unstuck the piston in the engine to move it to the top end?
@antiR3ality
3 жыл бұрын
Great and useful video. Thanks
@cookingchickenugget6924
Жыл бұрын
feeling more comfortable now
@AndrewGiles-h5y
Жыл бұрын
what have we damaged by overfilling the engine with oil, went for a ride not too far. the bike ran pretty well till i headed back home slowed for the drive way, then something went. biked stopped.can you suggest what we might have done? cheers
@dinggle-i3r
9 ай бұрын
alright this video is perfect im going to be attempting do pretty much do the hole top end part tonight and im praying that i don't have to get into the bottom end other then i want to put a nice clutch in ether hinson or rukluse depends on the prices but mines going out my rmz is pretty low hours it only has 14 on it when i went to take the valve cover off the spark plug that came from the factory was init but it did have a after market carb it wasn't anything special like a lectron carb sadly ill update ether half way though and the end or just at the end depends on how hard of a time its giving me
@ducaduke
2 жыл бұрын
Hey dude I got a question for you I’m about to take my head off my ktm. There is a locking crank port. But I can’t order one sinces there on back order. If I use a clutch holding tool to hold the front sprocket. So when I go to take the cam nut gear off it won’t spin and mess up my timing.
@benedettohero3123
7 ай бұрын
Good informal, high-quality video.
@noahbussey2247
3 жыл бұрын
Keep up the videos man! Best channel for this sort of stuff by far and that’s from years of searching lol nobody goes into any detail but you sure as hell do
@ducaduke
2 жыл бұрын
Do a ktm 625 high flow head please
@maurice5012
2 жыл бұрын
Thanks for posting this video. 👍🏻
@Smallmike1994
8 ай бұрын
yea 100% deserves more subs
@jasongenet3346
2 жыл бұрын
Does the piston pin get reused
@buckwild1123
Жыл бұрын
Great follow up vid
@samwittstruck.6685
2 жыл бұрын
Love your claw hammer.
@alekboi4016
2 жыл бұрын
thanks this was so helpfull
@plllot9713
Жыл бұрын
5:38 that small end play though 😵
@tonyshull741
3 жыл бұрын
Great videos! Thanks
@maxhellmich627
2 жыл бұрын
Great
@makincash3337
3 жыл бұрын
Great video
@bigting510
3 жыл бұрын
By any chance would you know what the problem is on my crf the kick start will not move and the back wheel is locked
Пікірлер: 34