Relays "tend" to be for logic switching. Contactors for power switching.
@ElectricianU
5 жыл бұрын
Most of the time you're right, but the fact you put "tends" to in there lets me know you're experienced in the field lol
@shnlj5910
5 жыл бұрын
Relays are used to switch solenoids frequently.
@Stones_Throw
5 жыл бұрын
Yes, relays are durable and inexpensive in "low power" switching applications.
@shnlj5910
5 жыл бұрын
@@Stones_Throw Right, not gonna see much over 120vac thru them. I haven't anyways.
@ser7ser7i
5 жыл бұрын
40 amps ssr
@dtv1966
5 жыл бұрын
Wow. I went through a 5 year IBEW apprenticeship here in Florida and you explained relays and contactors much better than the so-called instructor I had. Thanks.
@jamesmclaughlinprimitivele4587
5 жыл бұрын
Feel sorry for you, hope you found someone better to work with.
@gregphillips1998
5 жыл бұрын
What local brother.
@joegonzalez7386
4 жыл бұрын
Local 18, Los Angeles, sorry that you had that experience.
@1990hotness
3 жыл бұрын
Orlando?
@shnlj5910
5 жыл бұрын
The contactor you were holding in your hand will accept auxiliary contacts as well. Auxiliaries are used regularly for latch circuits and/or if there needs to be a sequence during a matching start up, switching a indicator light, sending a signal to a plc, etc. I'm an industrial tech, it's rare to see a contactor without auxiliaries attached.
@anandjoshi8554
2 жыл бұрын
Can I use contactor ..auxiliary /hold circuit for power cut off function in my device ? when the device send a trigger relay break input to the holding auxiliary circuit of the contactor? Basically I need this in my plc project to cut off supply whenever any emergency/error occurs.
@morelightpm457
5 жыл бұрын
Electrician for 22yrs, good video and much respect for the old school Nintendo controller hat
@AlejandroGonzalez-hx6bu
5 жыл бұрын
Wow, why I find better instructors on you tube than school.
@craigcharteris7026
Ай бұрын
Cant find a video of yours wiring up contractors? Really like your videos too!
@craigcharteris7026
Ай бұрын
Contactors not contractors lol
@justforlaughs8988
8 ай бұрын
So I'm looking at a relay/contactor it's for my vehicle there's a 9-32vdc switched leads for closing the the normally open coil that handles up to 500amps of current it's completely sealed with an epoxy with 2 bolts for heavy gauged wire I'm wondering if this is a relay or connector? My alternator currently puts out 15.5vdc internally regulated and clamps 430amps to charge up my (LTO) lithium titanate oxide battery I've built for car audio it's a massive bank capable of putting out 3200amps constant and 6400amps for a 60second clamp holding . The goal is to protect my alt but just wondering what it would technically be called whether it's a relay or a contactor? Thank dude love the channel
@AK-mx1sl
5 жыл бұрын
Thank you
@victoryfirst2878
2 жыл бұрын
How would I control one to four items 120 volts 15 amps heaters sequentially choosing to use one to four items on time per second or so each item sequentially ???? Can you help guide me Sir ??? Thanks
@zippythechicken
5 жыл бұрын
my understanding of relays is that a lower amperage signal/circuit controls a higher amperage circuit such as in a car for the starter relay where the key switch sends power to the relay which controls higher amperage out to the starter .. because you would never send all the amps for the starter through the key switch. in a relay the two circuits are independent and the lower voltage or amperage one controls the higher voltage/amperage circuit
@ElectricianU
5 жыл бұрын
That is definitely the case in automotive as well as some lighting and building control systems. But that's not always true in electrical in general. Many times I've used relays at higher voltages for controlling circuits of that same voltage. For example a 208v control circuit, switching several 120/208 circuits on/off at the same time.
@lanthonyperdum6430
5 жыл бұрын
That’s great information...I’m 1000% smarter about relays and contactors now !!!
@henrybartlett1986
4 жыл бұрын
Very useful.
@dsford1982
4 жыл бұрын
So how are these spec'd? I mean if I want a contactor that will pass 220v through it but is switched (coil) by 110v, how would that be identified? I want to turn on a 220v motor with a 110v switch...if that makes sense?Thank you for the video. I have subscribed so I can learn even more.
@bonusnudges
5 жыл бұрын
That was relay interesting !
@HelloKittyFanMan.
5 жыл бұрын
Haww... HAWWWW...! UB2 fun E!
@paulmanhart4481
Жыл бұрын
Interesting video. Thanks. I have a variable speed controller for a 130 VDC treadmill motor. I have a dpdt switch for forward and reverse. I’d like to have a green led light come on when it’s in forward (+-) and a yellow led light when it’s in reverse. But the LED’s are low voltage and current. So I need a switch that allows low dc voltage to flow to a led when the polarity is +- and when the polarity to the TM motor changes, it closes that gate and opens another. I’m doing a poor job of explaining it, but I hope you understand. Any suggestions? Space is limited. Thanks for your attention. Paul
@GoCoyote
Жыл бұрын
One can run two sets of LEDs connected to the appropriate resistor and a blocking diode in series, one green and one yellow, and then connect them in parallel with the power wires running to the motor. With them being connected in different polarities and the motor is moving one way, the polarity will only allow current to flow through the diode and the resistor to supply the proper voltage to light the appropriate color LED. Green LEDs have a different resistance than yellow ones, so each resistor will need to be sized accordingly. This will work as long as the speed controller is pulse width modulated (with some possible flickering of the LEDs) and not voltage modulated. If the voltage is modulated, then you will only have a narrow window of voltage that the LEDs will function in.
@paulmanhart4481
Жыл бұрын
@@GoCoyote Thanks. I’ll try it. I’ll have to lay it out to understand first. Thanks for taking the time to answer. It’s a shame that I can’t find a nice DPDT rotator selector switch that can handle 130 VDC and 20+ amps. I ended up with a monstrous 3PDT changeover switch that’s yellow and red. 3” deep. I wanted something a bit sexier in stainless. But even the 20 amp DPDT toggle switches don’t hold up to a 4.25 hp treadmill motor. May I ask you more questions about wiring? Do you have a website where I can send you pictures? I’m desperate here so I’m reaching out. Thanks, Paul
@DerekHundik
5 жыл бұрын
4:22 what's this
@HelloKittyFanMan.
5 жыл бұрын
So relays can handle more than a couple of separate loads, since you included 3. Maybe some can do 4, even.
@anwaruhibbi4482
5 жыл бұрын
My suggestion add subtitles at the bottom videos.
@ElectricianU
5 жыл бұрын
I would love to do this but it takes a lot of time so I need help from the community. Do you know you can contribute subtitles and translations in the “contribute” tab? If it’s something you’re interested in helping with please feel free to do so. If not that’s ok too, thanks for watching my friend!
@BelSei
5 жыл бұрын
What about Breakers, Switches and Disconnectors?
@ElectricianU
5 жыл бұрын
What about them?
@BelSei
5 жыл бұрын
The difference between and so on... While mostly mechanic, this might also be an interesting subject from an electrical and mechanical point of view.
@narutokun5765
5 жыл бұрын
Bro how to contact u
@minionman6177
5 жыл бұрын
So is it true that if I have a relay that the coil usually stays energized then the normally open contact is normally closed. :/ Wut?
@scottbc31h22
5 жыл бұрын
The term 'normally', in this case refers to the "at rest" or unenergized position of the contacts. The same terminology is uses to designate the contact configuration in momentary type switches.
@blakehorton8110
5 жыл бұрын
Why not just use a double switch or duplex switch , like two switches in one is what I mean , instead of using a contactor ???
@ElectricianU
5 жыл бұрын
You could do that for two things, but what if you want 6 things all controlled by a photocell. The contactor can be controlled without manual switching and work off of the sun going up and down on its own. That’s the benefit rather than you having to walk up to several switches twice every day/night to do it yourself.
@blakehorton8110
5 жыл бұрын
@@ElectricianU dizzamn you right ....yhea that was just a test see if you paying attention .... ughhem yhea that's right : /
@MrElNeNe07
Жыл бұрын
Wheres the video for how they work😅
@johnbutcher125
5 жыл бұрын
you can get laching relays
@tomporter2164
5 жыл бұрын
contactors can handle up to 500 amps
@richdiddens4059
5 жыл бұрын
Latching and unlatching relays are fairly common. Some also have manual over-rides to latch or unlatch. Not to mention the myriad specialty relays, multiple types of timing relays, alternating relays, current sensing, voltage sensing, etc. I started working in switchboard shops before PLC's came out and worked a lot with relay logic; panels with as many as 300 control relays of various functions. Troubleshooting? Oh, joy!
@Lessgetbrootal
5 жыл бұрын
My classmate created his own "stoplight" using timing relay cubes. They're fun and can be implemented into a bunch of different things once you understand how the N.O./N.C. functions work
@mrmalone28
5 жыл бұрын
Zach Nicastro yeah right
@artisanelectrics
5 жыл бұрын
Great video Dustin thanks a lot!
@anomalyirservicellp2676
5 жыл бұрын
This is a great channel with a wealthy info. Have you ever done any thermal imaging videos showing heating issues with electrical components.
@Rayram555
5 жыл бұрын
You are very knowledgeable. Very good explanation about the coil operation. I too am an electrician and constantly seeking knowledge from people like you. Learn one and teach one will make you a master. Thank You
@anandjoshi8554
2 жыл бұрын
Can I use contactor ..auxiliary /hold circuit for power cut off function in my device ? when the device send a trigger relay break input to the holding auxiliary circuit of the contactor? Basically I need this in my plc project to cut off supply whenever any emergency/error occurs.
@bjtaudio
4 жыл бұрын
A relay is a device where there is no emphasis on the closing and opening mechanical forces for making and breaking a circuit, meaning that current can be switched on via energizing the coil or it could be switched on via releasing the coil and relying on the spring to make a contact. A contractor is actually different as its intended to only ever close a circuit when energized, and slam down with considerable force hence the name "to make contact" Yes some units can be configured to break a normally closed circuit too. The aux contacts that piggy back on the contractor mechanism are an optional extra and are for low power use only. The reason why contractor are used to slam down and make contact hence the name in high power applications is because a large amount of force is required when switching high energy equipment.
@jas20per
Жыл бұрын
OK as far as it went but you missed some very important features of relays. Relays operate far faster than contactors, they also can handle much higher current than you said also they can have far more coil voltages and switch elements than any contactor. I would definitely want a relay at the end of an emergency stop switch for the speed of disconnection And most important you did not mention latching Relays sometimes called bistable relays , these relays only require voltage applied to the coil to move the armature one way and the contacts will stay open or closed without further supply current or voltage. Its state can be changed by applying an other voltage current pulse to change its state. Some of these type of relays have two coils to change state and others can have one. This type of relay is used in machinery switching using momentary action switches doing away with mechanical interlacing switch linkage far increasing reliability and speed of operation. I was taught that a relay is a fast precise electromagnetic component where a contactor uses slow brute force, one is a donkey the other a thurourbred race horse.
@fexking6367
5 жыл бұрын
Wow I loved your explanation- very precise and easy to understand. Thanks👍
@ElectricianU
5 жыл бұрын
No problem my dude!
@xephael3485
5 ай бұрын
I replaced a Type 91 Two Pole relay with an Eaton C25BNB230T. Didn't see a rating on how long it would last but I don't much care as the price is better.
@Fish6699
4 ай бұрын
There are Many different configurations available especially when you factor in Add-On NO / NC Contact Blocks. What you said isn’t Wrong, but the Easiest Way to distinguish each of the Three Types is: Relays = Control (Very Low Draw) Contactors = Control Power (High Draw and AIC) Starters = Contactors with Overload Protection (High Draw and AIC)
@wiktorkononczuk394
2 жыл бұрын
Bla bla bla bla facen szet !!!!!
@catsmeow5566
3 ай бұрын
Thank you! So, if I have a pump that is 230v w/ max draw of 6.1A, a relay could work for it? (I've seen relays that look like the one you've been holding in the video that do up to 250v and 10A). All I want is something to make a float lever tell the 230v pump to turn on when the float is down and turn it off when the float is back up to a certain point (to fill a cistern). Would the relay work for that? Any idea how to wire that? The float has 3 wires (with only 2 being used depending on what you want it to do-- in the one I'm looking at getting, the brown wire would be excluded if I want the pump to turn on when float is down). I keep trying go find diagrams but they say it is specific to the application.
@TlD-dg6ug
4 ай бұрын
Contactors typically have an auxiliary so that you can change from N/O to N/C, you just have to do it with the low voltage signal lines.
@lazycarper7925
3 жыл бұрын
please can you help a noob, can somebody tell me if i can wire a 3 pole relay as a single pole, i think thats what i want/need?, i needed a relay to turn on and off from - 24vac,on the coil side-, 240v 35a on the main load , and with out spending silly money i could only find a 3 pole one cheap, thats 35 amps , all i need it to do is when activated by the 24v ac , allow the current of my 240v ac to pass to make the circuit, and that can be just the live or the live and neutral, etc etc if it can be done?, would wiring it so my live splits and goes in to all 3 poles and then out all 3 poles(when activated), to give more current, as its for my mig welder ,(24v trigger), so more amps the better, thank you
@Shredxcam22
4 жыл бұрын
TDLR. They are the same. Check the ratings before using them. The biggest difference is spelling.
@troublets3060
4 жыл бұрын
Simple explanation for a relay is a switch that uses a lower power load to operate to switch a higher power load. Saying a relay is only for small low power uses is simply false. Go look at an older car with a starter relay separate from the starter. You have the small wires which control the coil operation in the relay. The heavy gauge battery cable and cable to the starter are connected to the contact points for the relay. I stumbled on this video and watched all the way through in case I was missing something but it was just in accurate.
@Mopardude
5 жыл бұрын
If you take video requests I wouldn't mind hearing your perspective on why with low volt LED lights why or how it works that you need both the magnetically switch trans and a special dimmable switch as well.
@alexanderboyd2280
3 жыл бұрын
Can you Please Please PLEASE DO A VIDEO EXPLAINING THREE PHASE POWER
@Loredo_1
Жыл бұрын
Dude, come on now. A relay is use for example: for a DO to control a 4-20 gas detector.
@Dannzegos
5 жыл бұрын
I would love the comparison had been a bit more technical instead of generalities. I appreciate the video though.
@klfjoat
Жыл бұрын
So we use a completely different word for something that's higher current? 😂
@sarag1158
Жыл бұрын
I'm an HV AC controls electrician. But I'm in my second year of doing it. I keep calling contactors relays. thank you for making it so easy to search this topic.
@patrickbrenmore4092
2 жыл бұрын
A relay is a baby contactor. If the device is rated for 10A or more its a Contactor. If the device is rated for less than 10A its a relay.
@adamthethird4753
5 жыл бұрын
Eeh...you are generally correct...if explaining to someone who knows nothing about anything electricity.
@ElectricianU
5 жыл бұрын
If you couldn't tell...that's exactly what this whole channel is about.
@dustinmccartneyjr5136
4 жыл бұрын
And it is widely appreciated dustin I have learned a ton from both this and the journey to master channel's over the past 2 years and look forward to eventually getting my foot through the door in my area thank you
@rob8823
Жыл бұрын
Can I request a video decyphering the contact ratings on the side of these contactors? ac 1, 2,... 20, iec, ul. Ac vs Dc etc. Thanks for your incredible channel.
@Build_the_Future
5 жыл бұрын
You should do a video on pulling wire in conduit and laying out what Neural wire goes with what color and circuit number. also on what numbers are associated with wich colors. lots of apprentices have problems with this and they like to mix up the neutral wires with the wrong circuits. Thanks
@Ryan-hr9hw
4 жыл бұрын
You cant fix stupid.
@thzzzt
3 жыл бұрын
4:10 But there IS an animal called a "latching relay" which preserves its state even when the input is gone. They toggle given pulses from a momentary switch.
@cdw3423
5 жыл бұрын
You can get relays that also have latching. The ones I am familiar with use a magnet to hold the contact closed.
@NipkowDisk
5 жыл бұрын
Yep- the very early AMF bowling pinspotters used several latching relays for control.
@scottbc31h22
5 жыл бұрын
@@NipkowDisk So did old traffic light controllers
@johnlupo3919
3 жыл бұрын
YOU HAVE EXCEEDED YOUR "SO" QUOTA FOR THE DAY!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
@axelbrode
5 жыл бұрын
Contactors also are able to have extra contacts easily installed on the top either n/o or n/c to provide additional circuits to be added as required.
@camron2674
5 жыл бұрын
(Auxiliary contacts)
@anandjoshi8554
2 жыл бұрын
Can I use contactor ..auxiliary /hold circuit for power cut off function in my device ? when the device send a trigger relay break input to the holding auxiliary circuit of the contactor? Basically I need this in my plc project to cut off supply whenever any emergency/error occurs.
@axelbrode4673
2 жыл бұрын
Sorry to say I don't know.
@Mishn0
5 жыл бұрын
So it's just nomenclature, they're all relays.
@RB-xv4si
4 жыл бұрын
It’s not just nomenclature. Relays typically have normally closed and normally open terminals and can be used for more complex operations than contactors. Contactors are essentially big heavy duty switches that can switch on multiple circuits at once. They’re big dumb switches that handle a lot of current. Relays usually can’t handle much current but can be used for logical operations, like turning on one device and turning off a second device at the same time.
@califeroan
4 жыл бұрын
Your video is great, but the sounds you use are so f*cking annoying.
@amanhamidi37
4 жыл бұрын
I am still waiting for your video of the conductor and relay wiring.
@rickreep9089
5 жыл бұрын
I need a dpdt contactor or relay, 24 or 110 ac coil, to power a Grunfos ac/dc well pump powered by solar during the day and utility power at night. Can’t find one to handle the load of the dc without burning the contacts. Need 110 ac 15 amp on the normally closed side and 100 vdc 20 amp on the normally closed side. Can you refer me to a product.
@jesseblanchard9609
5 жыл бұрын
There's a tonne of class ntactors out there that will handle that load with no issue at all. I controlled 480v 50A loads with 120/20 for cranes on a regular basis. Any electrical contract supply house should be able to help you out with specific units, they won't be cheap...
@daveb6722
5 жыл бұрын
So in other words a contactor is a heavy duty relay.
@ikbendusan
4 жыл бұрын
yes
@RB-xv4si
4 жыл бұрын
Not exactly. Contactors are like super-duty on/off switches that are controlled by another circuit. Relays have leads/terminals that are normally open and normally closed, so they can be used for more complex operations.
@daveb6722
4 жыл бұрын
@@RB-xv4si That is exactly what a relay is. One circuit energises a coil to flip a switch. A lower power circuit can switch a higher power circuit.
@RB-xv4si
4 жыл бұрын
Dave B I don’t think you’re processing a significant difference. Yes, it is operated by a circuit sending/cutting off voltage to its coil, like a contactor. But relays also have NO and NC terminals or leads. That allow them to send voltage and cut voltage to multiple devices at the same time.
@daveb6722
4 жыл бұрын
@@RB-xv4si Back when I posed the observation I was an electronics engineer that had been asked to learn electrical switching so I researched what I could to get up to speed with terminology, things like contactors were a new entity until I striped one down to find that it is just a type of relay. To do the job I had been asked to do I needed to know exactly what components were irrespective of their name so that I could design circuits using existing equipment. A contactor is a cheap one trick pony version of a relay, hence why they are used so often. Its not the only electronics definition that has been changed for the electrical trade, LED is another one.
@edwardgilmour9013
5 жыл бұрын
Did you discuss the activation Voltage on the coil ? AC versus DC?
@HelloKittyFanMan.
5 жыл бұрын
When did "[v]oltage" become a brand of some sort, to you? You're asking if he discussed that because... you didn't watch the video, or...?
@RS-jh2kl
4 жыл бұрын
Let's get that onto a tray. Nice.
@SPeeDKiLL45
3 жыл бұрын
did not now ragnar lothbrok does youtube videos
@j05ephtube69
3 жыл бұрын
The spider tattoo is very distracting man 😄
@HelloKittyFanMan.
5 жыл бұрын
Actually, with a normal switch you can control as many different things as you can afford to load it with. Just run them in parallel.
@RB-xv4si
4 жыл бұрын
But the switch has to be rated to handle the current you’re sending through it. And it can only be manually controlled. No automation.
@Samlol23_drrich
4 жыл бұрын
What a great video. Well done. If i have a 50A breaker (which is probably too big) servicing an old Lennox (armstrong air) condensing unit, and my contactor craps out, can I use a 40A contactor? The condensing unit is 30 years old snd has no markings on it at all. No idea how many tons, or what contactor is in there now. Obvously, just looking for an opinion, from someone who knows more than I do. Everything is working, I just like to understand how the stuff inter relates. Thanks.
@joselitoloreto5719
5 жыл бұрын
Wow clear explanations. Thanks bro.
@johnlupo3919
3 жыл бұрын
HORRIBLE MUSIC ON THIS VIDEO!!!!!!!!!!!!!!!!!!!!!!!!!!!!
@darkbeekeeper
5 жыл бұрын
Nice job. Beefy
@wsvitak
4 жыл бұрын
We’ll said. Thanks for the information.
@thumbsup9208
Жыл бұрын
Anywhere you use contactors there are motors
@wiktorkononczuk394
2 жыл бұрын
Lysyn bla bla men show i sharap !!!!!!
@mjmjersey
2 жыл бұрын
I have a question. Let's say I wanted to have 4 landscape lighting circuits. Could I use 4 GFI Breakers then go into a lighting contactor to feed each individual contactor and or landscape out., could you also show me how you would do it if possible thank you
@ElectricianU
2 жыл бұрын
GFCIs might not like the contactors per say. As it is looking for any sort of short from A to B. But it is possible to do something like this yes.
@mjmjersey
2 жыл бұрын
@@ElectricianU thank you for responding I enjoy all your videos
@Wroe
11 ай бұрын
What's with the picture 4.22 ?
@brianburnside5949
3 жыл бұрын
So they are basically the same thing.
@degu44
3 ай бұрын
very good explaination of the two. I have a HVAC unit where the contactor is failing and had no idea what it was. Once I looked it up I said that's just a posh relay. But you have expanded my understanding of these, thank you.
@ElectricalSolution
5 жыл бұрын
Very useful video.
@MasterChief-sl9ro
5 жыл бұрын
Any Relay\Contactor can be configured for NO\NC.. Using either Grounding\Neutral\Power signal switching. Also relays can be rated up to 100 amps. But cost more then a Contactor of same rating. You can also change the coil line side control voltage for Contactors. In many configurations from 12 volt to 120 to control 277\480 volt line\loads... Some relays have timers. That reset after so many minutes. And relays are the best thing since running water for PLC systems.
@scottbc31h22
5 жыл бұрын
To add: Relays are available with coil ratings of nearly every standard system voltage, from 3 volts up to 277 volts, AC or DC.
@anandjoshi8554
2 жыл бұрын
Can I use contactor ..auxiliary /hold circuit for power cut off function in my device ? when the plc device send a trigger relay break input to the holding auxiliary circuit of the contactor? Basically I need this in my plc project to cut off supply whenever any emergency/error occurs.
@mohfiroz7700
Жыл бұрын
Contractors are equipped to wider gap in case of opening circuit so they have capacity under induction loads and limiting arc. Relays has no ability to extinguishing arcs, the open contact gap in relays are smaller than contactors. For switching off a 16A electromotor or induction loads such as transformers, you need a contractor not a relay, calculated in correct rating which not necessarily that 16A. The opening speed of contacts in a contractor is faster than a relay. The main difference is braking current capacity.
@MattLeitholt
7 ай бұрын
That was super satisfying, and I'm thankful for your help! I'm looking to turn on and off a 30amp motor with a smart plug and a contactors seems like the right path.
@EnergySeeker
3 жыл бұрын
nice video , is it possible to have contactor which is 6 NC and 4 NO and they switch the NC to NO and vise versa ? if yes can you please give me a info where i can find such a device thanks a lot
@bjtaudio
4 жыл бұрын
Please note the fact that a contactor is typically bigger and heaver, high power etc than a relay is missing the point of why a contactor is called a contactor. A relay is a device where there is no emphasis on the closing and opening mechanical forces for making and breaking a circuit, when with a contactor there is emphasis hence the name to slam down with considerable force and make contact.
@tgsharp1158
Жыл бұрын
This is how a real teacher looks.
@bjtaudio
4 жыл бұрын
Please note the fact that a contactor is typically bigger and heaver, high power etc than a relay is missing the point of why a contactor is called a contactor. A relay is a device where there is no emphasis on the closing and opening mechanical forces for making and breaking a circuit, where with a contactor there is emphasis hence the name to slam down with considerable force and make contact.
@xLopez210x
4 жыл бұрын
little late to the game here but question..... wiring a trailer dealing with shore power 120v, and battery 12v, switching from shore power to inverter power, could you technically use a 30 amp relay as oppose to a 30 amp contactor?
@oconaddify
2 жыл бұрын
3:12 what type of relay would allow me to open the N/C switch while closing the N/O switch with only one control voltage source?
@skasti
Жыл бұрын
You wasted my time little bit
@michaelkeith5178
4 жыл бұрын
On Relays the Nickel Cadmium on the Contacts is rated for Less than 20amps used typically for lower voltages single phase. Contactors are typically 20amp or greater and up to 3phase with auxiliaries
@samroybull764
2 жыл бұрын
Was reviewing stuff for a 50 year old machine at work, and you may have just saved us a few hundreds of usd lol, thanks man
@network_king
3 жыл бұрын
I usually think of them about the same, contactor usually I think large loads or motors, 3 phase things. I think a contactor for a motor though is a bit different with fuse links, etc I think that is called a starter to me it is a contactor.
@eppinizer
3 жыл бұрын
I appreciate the informative content, but the wacky sound effects are a little much ;)
@janl6032
3 жыл бұрын
Hi! Greetings from Finland. Your videos are awesome. I'm an electrician and now studying to come a ship electrician.
@ceeball9525
2 жыл бұрын
Hey Dustin, Do you have a video on how to wire relays and contactors? Fire alarm, door mags
@SamuelItodo-vu7ng
5 ай бұрын
you are awesomwe
@zeus3358
5 жыл бұрын
I was hoping you were going to explain how one is mechanical and one is solid state. Explaining the pros and cons.
@theerthac7021
3 жыл бұрын
Does the contactor isolation provides safety in lightning??
@isaacayotte3822
5 жыл бұрын
Putting out information that apprentices might not get on the field (or in school evidently), Awesome. Just some viewer feedback... Not sure if anyone else feels this way but I almost miss your garage studio. I mean, the wall frame and tar paper in your garage was a cool theme in my opinion. I realize you might be going for a more professional and organized look for Electrician U, but it would be cool if you got a little creative with the background in your studio to add some style and a new texture to the videos. The current background is neat and clean, but not as interesting to me. Other than that, The content is very interesting!
@darrenwardell3079
2 жыл бұрын
Excellent explanation many thanks from the UK👍
@crazykick680
3 жыл бұрын
great video
@cui4170
4 жыл бұрын
Which one is used in split ac..i have 1.5, 2 and 2.5 ton a/cs ?
Пікірлер: 213