He's added the music to distract the viewers from his pathetic work practices.
@bajecznyjulek8154
Жыл бұрын
definitely... ...at beginning uncomfortable, after realising - more focus on tech side - for "know how" Im here.... then music its actually interesting.... only for something else... ...any way, going .....and about half way through- .....Im in interesting forms of expression....and its experience, as a whole, material - that take my feelings and then thoughts.... nice, I like it thank
@lindamoggioable
4 жыл бұрын
Annoying and unnecessary music. Quiet is good.
@paulwright2906
5 ай бұрын
Support the job on a block of wood , that bounce is taking away at least 1/2of your force.
@joannalewis8623
Жыл бұрын
Thanks. I looked everywhere on the web for how to fit this type of pin in a door handle! I suspected the only way was to use a hammer but didn’t want to try without knowing for sure. Also, I couldn’t get the pin in the other handle but your basic screwdriver wiggle action has helped me work out how to align it properly!
@km4hr
2 жыл бұрын
Thank goodness for for the mute button.
@chewytreyman
2 жыл бұрын
This video really helped me; I stopped biting my nails, and I pulled the crappy nails and screws out of my old hammer, brushed the head with a wire brush and lubed it, put in a new hammer shaft and a solid wedge. Soaked it in walnut oil for a few days and VOILA. My life is a lot better :D
@donaloriordain2260
7 ай бұрын
Well done, I had been trying to get the pin out yesterday with no luck. But used an Alan key and presto it worked. Thank you so much for putting this video up excellent video, top class.
@VenugopalanCheriyaveettil
3 жыл бұрын
It will be good to support the part close to the pin hole with a wooden piece. Apart from unnecessary transverse movement, it would also prevent bending stress at the root of the component where it is supported.
@andreava1213
3 жыл бұрын
Couldn't watch entire video the music was too distracting in a bad way..
@bretolson8484
3 жыл бұрын
Good content but that music is beyond horrible and loud.
@NoferTrunions
Жыл бұрын
Extraction from Blind Hole I was hoping for. Thanks anyway. TIP: you don't need background music.
@davidfriedland999
3 жыл бұрын
Video helped me. Cutting the bend off and using an allen wrench was the tip i needed. Thanks.
@mikeschumacher9715
4 жыл бұрын
That thing bouncing all around was pure pain. Reshoot this the proper way and post it. And once the screwdriver is put in the top, no need to run it up the bottom. The pin will align everything up on the way in.
@Tesla1254
2 жыл бұрын
Music is way too loud and distracting that I couldn't get past the first few seconds.
@vasi5518
4 жыл бұрын
Loud ass music ruined the entire video
@rickymeadows5176
8 ай бұрын
When I saw the yoke bouncing in the vise upon every hammer blow, then the angle grinder cut-off wheel minus the wheel guard, that was enough for me. Time to move on.
@rayceeya8659
5 жыл бұрын
I ran into this one on the wheel of a pallet jack the other day. I didn't have a small enough punch so I used a C-clamp, a screw and a nut to get one of these out. On one side of the C-Clamp i had the screw, and the nut was to give the pin someplace to go. I knew as soon as I got it started it would pop ring out with a pair of channel locks. I just needed that quarter inch. Unfortunately I launched the thing halfway across the warehouse as soon as it gave way. I said "to hell with it" and replaced it with a bent nail for now.
@warrenoakes3421
8 жыл бұрын
A darn lot better if it was on something solid
@julianhernandez1939
5 жыл бұрын
VOLUME WARNING! Come on man.
@ericroberts1231
4 жыл бұрын
All the wrong tools, sorry about the grinder marks on your bearing.
@jeffsuderman544
6 жыл бұрын
What do i do if the pin broke and the shaft turned to I can't push it through? Also I can't re a line it.
@midastouch84
2 жыл бұрын
Thanks, helped me fix the sawmill.
@tehdumah
Жыл бұрын
solved my problem - thanks
@muddyhotdog4103
3 жыл бұрын
Add grease, makes insertion smoother
@garydowd7313
2 жыл бұрын
It’s not a recess on the ends. That’s called a bevel.
@hollowdog7208
6 жыл бұрын
This is why I don't let strangers work on things I own.
@haberg77
5 жыл бұрын
How do you do it? Post a video.
@terryandteresa
Жыл бұрын
You mean a bevel at the end? It was not recessed
@johnranallo424
5 жыл бұрын
Why the music?
@nochan99
3 жыл бұрын
Sir, thank you for curing my fear of doing it wrong. I feel like a surgeon after watching this vid!
@Dan-oz4qb
3 жыл бұрын
Music isn't necessary and is annoying AF.
@timarcher5695
7 ай бұрын
It's a Tigger vice. Bouncy bouncy bouncy bouncy fun fun fun fun fun
@ranganathn9635
3 жыл бұрын
This assembly is probably creating more damage to the bearing than the pin.
@jwb4291
5 жыл бұрын
This is an older video so idk if you'll reply But what it the pin cant be punched through - how do you..pull it out
@johndenicola6173
5 жыл бұрын
He hasn't replied, you can use liquid wrench and continue to try to punch it out.. .another thing is to try to drill it out (use a drill to cut up the pin until it is weakened then pop it out.
@radioace318la
Жыл бұрын
you are losing all your kinetic energy with that in a vice or whatever it's clamped in. It should be sitting on a solid surface.
@fun_ghoul
5 жыл бұрын
The lesson of this video: Don't do what this yutz does.
@haberg77
5 жыл бұрын
How do you do it? Post a video.
@johndenicola6173
5 жыл бұрын
Other than not having his work closer to the vise (which caused a lot of unnecessary bounce), the rest of the advice seemed fine. Cut the pin down, drive it through the shaft to remove it, simple stuff (once it is freed if frozen in the shaft).
@ashwilliams4989
3 жыл бұрын
Master, how remove Slotted Spring Pin from blind hole?
@Nzchimeran
3 жыл бұрын
also i have this issue on a Weber carburetor fuel spigot. It is a blind hole, 2mm diameter, drilling is risky.
@Zack-id1xo
3 жыл бұрын
Drill
@ashwilliams4989
3 жыл бұрын
@@Zack-id1xo I found a better solution. To remove the Slotted Spring Pin just fill the hole in which it is mounted with oil or a thin grease to about 1/4 the depth of the hole. Then choose a minimally smaller diameter pin punch and hit it with a hammer. Pin punch will act as a piston and will spring oil which will push out the slotted spring pin from hole. Note: The pin drift must fit tightly in the sllottego spring pin (hole)! Wear safety goggles and cover the hole with a cloth to shield yourself from the gushing oil.
@kevgh3869
2 ай бұрын
Who calls them elastic pins anyway! And why wouldn't you hold the end you are working on in the vice instead of having the job sticking out and bouncing around like that!
@amotz35
4 жыл бұрын
all the wrong tools used. you use a ball end punch for this ! and stop using angel grinder to cut things ! and without a hand shield ! why would you ever use an angel grinder without a shield ? are you so anxious to go to the o.r. ? i have 8 years xp as a plumber and some years as a construction worker and one of the things i thought all my collages : use oscillating tool or reciprocating saw / sawzall ! do not use angel grinder to cut things !
@sdbackof
4 жыл бұрын
Yeah, that’s beginner level... how about the ones I’m currently doing that are a 1/4” in length and 5/64 in diameter
@davidmaj4259
2 жыл бұрын
Make a video about it
@chlyon
5 жыл бұрын
Farmer Joe s YT channel , could not wait to read comments , alas somewhat disappointed with the comment sections reaction to this gentlemans fine work .
@wardencobb7442
Жыл бұрын
This music is AWESOME.
@tampabaylensman
10 ай бұрын
Didn't show blind extraction
@eBell05
3 жыл бұрын
source of music?
@enricopallazzo3244
3 жыл бұрын
Darude-Sandstorm
@TerryWhisk
3 жыл бұрын
Hell
@eBell05
3 жыл бұрын
@@enricopallazzo3244 I wish
@matthewshane307
5 жыл бұрын
ridiculous
@garykent8193
4 жыл бұрын
Complete waste of time! Everyone knows this method. How do you remove it when you can't drive it thru?
@garykent8193
4 жыл бұрын
Sorry bud not trying to be rude, it was one of those days, I had a problem and had to figure it out. So I turned to KZitem. The tittle of your video is misleading though. Ya might wanna change it to " drive thru method" or something. I have come upon the problem before when the pin needs to be removed, but can't be driven thru because of solid surface on the other side. The pins are hardened so its hard to drill it! I did get the pin out, by the way. Have a good day!!!
@Gamogamer
4 жыл бұрын
@@garykent8193 Hoiw did you get it out?
@garykent8193
4 жыл бұрын
I used a machine bit and cut it out in the machine/drill press!
@runamuckretreatmccarthy1554
5 жыл бұрын
Not so easy when you're trying to reinstall the roll pin under a dash, to reconnect your stearing column to a rack and pinion. I see 50 "easy methods" of removal and installation of these pins, on everything you can name.... where you have room to swing a hammer, etc... Someone pleeeease show me one in a tight, hard to reach area. Not to critique your video, but anyone could eventually figure that out, or any pin, that they have easy access to. Its the not so easy access ones that are the problem.
@flyguy807
5 жыл бұрын
Ok all you critical ' tourists' ; if it is so easy to do, where is your " method" on video??!
@runamuckretreatmccarthy1554
5 жыл бұрын
@@flyguy807 , do a search for "install roll pin" and 50 "easy methods" will come up. And in those videos, they are easy... cause the areas its being installed has all kinds of room to work. The jobs they're doing can easily be done in 5 min or less, using a pair of vice grips and a hammer, kind of like I did under a steering wheel, behind a break peddle.... except there was no room to swing a hammer.
@doctorboy5892
5 жыл бұрын
Wack the shit out of it. That’s how I do it too and it works. Or drill the shit out if it if only comes out one way.
Пікірлер: 76