Remember when you wanted to swap the subframe in 2 hours at my place 😂😂😂
@RexH
11 ай бұрын
Can you swap my Ef too please
@ashleypike878
11 ай бұрын
Unfortunately the E series are already going up in value so I doubt they will be the next au 😢 I personally think it’s going to be theba/bf as they where so mass produced and there really was nothing special about the ba/bf xrs compared to au and e series which where tickford enhanced, just my thoughts 🤷♂️
@andrewg2618
11 ай бұрын
Correct. The E series XRs are already more desirable than BA/BFs (except BA/BF turbos of course)
@bill13690
11 ай бұрын
HI Nathan. Great to see you out there working again mate. My first car was a lemons Red EB series 2 - Ford Falcon GLI station wagon - Factory 5-speed manual - Dual Fuel ⛽. Keep it all coming my friend. Cheers from William. mount Gambier South Australia
@efxr6538
11 ай бұрын
Nice, would love red EB or ED!
@danieljones7843
6 ай бұрын
My first car was a LeMans red EF GLi station wagon - Factory 5-speed manual with factory dickie seat. No dual fuel though.
@jaydenholton5188
11 ай бұрын
I just put a B series K frame into my EF drift car and honestly so keen man. I’m going barra turbo so hopefully I don’t send my T5 into jupiter instantly
@garagepc9645
14 күн бұрын
How much of a difference did this make to the handling of the car?
@FORDLYFAOTEAROA
10 ай бұрын
Fluff that,weld the whole AU inner chassis rail in...125mm from the E series sway bar bracket to the rear most au subrame stud,job tidy. Cut 20mm from the top centre of the au sway bar bracket so it's only 60mm wide,weld that künnt to the original sway bar mounting point on the E series.
@vlion_3078
10 ай бұрын
Just a quick one would someone be able too link the control arms he mentioned at the end of the video can’t seem to find them
@peter_brash
11 ай бұрын
Can you EF subframe swap my AU pls 🙏
@TURBOTRISTO
9 ай бұрын
I REMEMBER WHEN THIS GUY USED TO MAKE KZitem VIDEOS
@RC.Car.007
10 ай бұрын
Put a turbo on the hyundai getz please make a video of the hyundai getz
@sheffOG
11 ай бұрын
always uploading informative and entertaining videos keep it up lad 🤙
@nickprostizenovski6948
8 ай бұрын
So BA sub frame same same and what was that tool u use to cut the crush tube
@nathanpaykin
8 ай бұрын
Yeah exactly. I used a dremel because my grinder was too fat to get into that gap
@nickprostizenovski6948
8 ай бұрын
@@nathanpaykin dremel as in a burr ??
@efxr6538
11 ай бұрын
Great tutorial mate!
@ourcrazylifenorthislandnz
11 ай бұрын
good stuff mate
@tturi2
11 ай бұрын
an alternative way to do the crush tubes is to weld the crush tubes to the studs and weld the top of the stud to the rails like the ba falcon, if I do an au front thats what I'll attempt, au irs first for me though
@imidsikkey
11 ай бұрын
.... I think I'll just save up and pay hoppers stoppers when I'm ready 😂 Otherwise I'll end up with more holes than swill cheese
@JWOLDING
11 ай бұрын
Yep, the price of the E series will go up with this easy mod... 😂😂
Пікірлер: 26