Bill, you were right, that first pin greaser was the correct one to use. But that end is too large. The one I used for many years the end is much smaller. Also I put a slight bend in the tube which which makes it easier for some u joints and CV shaft center bearings. Try a regular auto parts store, hopefully they don't have another China one like you have. Take yours along to compare before purchase.
@AStanton1966
5 жыл бұрын
Thank you for making this video. I positively now know that I never want to buy one of these things.
@regsparkes6507
5 жыл бұрын
Makes you think that way, doesn't he? I've been shaking my head watching these 'mechanical antics'.
@eosjoe565
5 жыл бұрын
The purpose of changing the final drive fluid is to flush out the initial metal shavings. It's listed in the manual for a reason.
@thegoprogroup3420
5 жыл бұрын
Hey just to let you know your new truck oil filter takes cartridges as well but it is easy to change it out because it’s not in a hard place to reach it because my brother a power stroke like yours but it is actually the 6.4 model engine including my dad has a 6.0 and he has to do the same thing you do for your truck on his for when he changes his oil at home! Just letting ya know so that when it comes time to change it you’ll know where it is located on the top of your engine
@classicxl
5 жыл бұрын
Hey bill try using a socket to loosen the oil filter cap it may be easier .my 14 Jetta tdi has the has kind cap and filter I use a 32 mm socket from crappy tire
@Oliver1071
Ай бұрын
Funny I bet all of the people buying low profile ramps are saying why didn't I think about that just going backwards LOL.
@jeffreymurdock8366
5 жыл бұрын
Hey Bill, little trick to do final drive. Use a short length of rubber tubing to refill it. That's what I do in tight spots like that. Works very nicely in most cases.
@G-Man-kc2nm
5 жыл бұрын
Nice work Bill. I have the same problem you have. Seems as if they make cars too close to the ground. Na I’m just getting fatter...lol Every house needs a pit to work on these darn cars..Thanks Bill.
@coreymchugh363
5 жыл бұрын
if I'm not mistaken that grease zert has a bolt around it try take that bolt of. I've seen a few that are like that and reasoning is so the nut protects the zert fitting itself from being sheared off. I could be wrong but a suggestion kinda like lubing a weed whacker head
@1YouTube_you
4 жыл бұрын
Man you don’t need to go through all that to change the oil! I did mine on a level surface without ramps. All you need is a long extension.
@JoeSmith-ov4go
5 жыл бұрын
Bill, the True Canadian!
@eosjoe565
5 жыл бұрын
Why are you questioning the drain plug torque specs? You saw yourself when you removed it that it wasn't very tight. I'm sure the factory tightened it correctly. Aluminum drain pans don't like tight bolts.
@billstmaxx
5 жыл бұрын
That’s awesome for them when it vibrates loose and the oil drains on the road. I get torque specs but that was barely tightened.
@eosjoe565
5 жыл бұрын
@@billstmaxx I understand but keep in mind you were on the other end of an 18-inch ratchet. Had you been using a normal wrench it would have probably felt plenty tight. When it doubt - always go with the published torque spec.
@seenithere
5 жыл бұрын
Maybe try a LocNLube fitting on the grease gun, best thing since sliced bread!
@eosjoe565
5 жыл бұрын
I love the LNL coupler but you'd never get it in there on that drive shaft as the barrel of the coupler is a bit larger than a standard grease gun coupler.
@breazealeaaron5205
5 жыл бұрын
For the final drive buy a fluid transfer pump. Home Depot and auto parts stores sell them for really cheap
@joshreed7908
5 жыл бұрын
In the next video we swap a diesel into the 2019 slingshot 😂
@goneshootin6401
5 жыл бұрын
try greasing that u joint from the bottom .. might be more room
@farmboss6914
5 жыл бұрын
Nice video. Bill can you you some mowing video on the zero turn I love those videos? Keep up the good work.
@zx8401ztv
5 жыл бұрын
Ahh you took the oil level with it on the wedges, you may find i'ts a bit high now. I don't think it's as critical as you think, so don't lose sleep bill.
@billstmaxx
5 жыл бұрын
It was jacked on the back level. Hopefully it’s close
@jasongodin6488
5 жыл бұрын
Bought a new tractor once with 40 hours on it, They still had the breakin oil in it, placed 10-30 oil and the oil pressure came up 20pounds
@iggymac3473
5 жыл бұрын
Bill check out this post on a forum they use a stranded grease fitting and grinder down a bit. U Joints With A Needle Nozzle you need the hard pipe grease gun to work rubber hose to hard to hold. www.slingshotforums.com/threads/lube-the-driveshaft-universal-joint-grease-fitting-zerk-regularly.3783/
@chadder19k
5 жыл бұрын
Hey bill just a heads up not sure if you know this or not but with gm motors you have to run that Dexos oil. A mechanic buddy of mine told me have to run that in their and if you don’t run it in their and something happens to the motor gm won’t back it if they find out you didn’t use dexos oil
@Chuckiewashere
5 жыл бұрын
Well saying it was built by Polaris and Covered under Polaris's Warranty your "Mechanic Buddy" doesn't know what he is talking about
@chadder19k
5 жыл бұрын
Charles Stuber I’m not talking about the Polaris, what I was saying is that gm motors take dexos motor oil if you want anything covered from them and my buddy is an ase certified mechanic so I’ll take what he tells me on Chevy stuff
@zaceribarkhouse3592
5 жыл бұрын
U have a lot more leverage with a longer handle then what ur standard 3/8 drive would be
@billstmaxx
5 жыл бұрын
That is true
@dy1837
4 жыл бұрын
what was the torque spec for the header? I did not see that in the 500 mile break in period
@dphillips705
5 жыл бұрын
not saying it is the same on those by any means but usually on vehicles the hatch mark area indicates 1 letre?
@VIheavyequipment
5 жыл бұрын
maybe its because they use a break in oil that lets it wear in faster
@poeticdisaster7500
5 жыл бұрын
My uncle and aunt got hit by a van, on his Harley Davidson 3 wheeler.. both had broken femurs, aunts hip broke... 1 year in hospital and rehabilitation now a millionaire... has another Harley 3 wheel etc.... please be careful . ... there is a reason they banned 3 wheelers in the 80s
@jspell3539
4 жыл бұрын
You do realize that a Polaris Slingshot is much wider and longer than any motorcycle right. Its actually wider than a Chevy Corvette. No one has ever said that traffic cant see these. It is the opposite actually. 99% of traffic stare at you so its not like your missed in traffic. I have ridden motorcycles and had times when I was almost hit. Never with my Slingshot.
@johnmilner7603
5 жыл бұрын
When you use a torque wrench, if you can, use it without a universal cause the torque multiplication is not exactly the same. 18 lb ft =216 lb in and not 214. 18x12=216. You need a new batt in your calculator. Specs of metal are in the oil from machining and that's why the 1st drain interval is low km/mi. You want the crud out. Invest in one of these to fill your rear axle and manual gear box my1970z28.com/COPO/images/suction_gun.JPG For greasing the universal on the driveshaft, I use the small grease gun from Crappy Tire and I used a grinder to grind the side wall of the grease fitting on the grease gun until it fit. Use QTS, it's easier. WTH is 4.8 L? Really. Whomever writes the manuals are not always correct. Use the dipstick and record the Qts for next time.
@rolablox1009
5 жыл бұрын
"In Bill's next video, he shows us how to tow a Slingshot back to the dealer.
@billstmaxx
5 жыл бұрын
What are you on about?
@anthonyyoung7344
5 жыл бұрын
Where did you get that grease kit.
@JimBobZee
5 жыл бұрын
Amazon Prime
@eosjoe565
5 жыл бұрын
You can't be serious. That is the simplest oil filter change I've ever seen. Try doing a similar cartridge swap UNDER the engine with the cartridge pointing DOWN. Talk about a mess. Why oh why is everyone moving from spin-on oil filters back to cartridges that require all sorts of special tools? I mean, my old Ford 8N used a cartridge and the first thing I did was covert it to a spin-on. Why? Because spin-on are way easier and no special tools required.
@billstmaxx
5 жыл бұрын
I like the invention of the spin on
@AStanton1966
5 жыл бұрын
I believe that the new Mustang Shelbys use cartridges as well as the Dodge Charger. We have one on our Jeep Cherokee Trailhawk and I hate it. Because it sits on top of the engine, if you get it wrong, it leaks all over your engine. I also heard of people cracking the cartridge's housing during an oil change. Another PITA to worry about.
Пікірлер: 46